Sentera Controls RTR-1 Service-Handbuch

RTR-1 REMOTE SWITCHED 230 VAC

TRANSFORMER CONTROLLER

Mounting and operating instructions

www.sentera.eu

MIW-RTR-1-EN-000 - 12 / 04 / 2021 2 - 8

back to the table of contents

RTR-1 REMOTE SWITCHED 230 VAC

TRANSFORMER CONTROLLER

Table of contents

SAFETY AND PRECAUTIONS 3

PRODUCT DESCRIPTION 4

ARTICLE CODE 4

INTENDED AREA OF USE 4

TECHNICAL DATA 4

STANDARDS 4

OPERATIONAL DIAGRAM 5

WIRING AND CONNECTIONS 5

MOUNTING INSTRUCTIONS IN STEPS 5

VERIFICATION OF INSTALLATION 7

TRANSPORT AND STORAGE 8

WARRANTY AND RESTRICTIONS 8

MAINTENANCE 8

www.sentera.eu

MIW-RTR-1-EN-000 - 12 / 04 / 2021 3 - 8

back to the table of contents

RTR-1 REMOTE SWITCHED 230 VAC

TRANSFORMER CONTROLLER

SAFETY AND PRECAUTIONS

Read all the information, the datasheet, mounting and operating instructions and

study the wiring and connection diagram before working with the product. For

personal and equipment safety, and for optimum product performance, make sure you

entirely understand the contents before installing, using, or maintaining this product.

For safety and licensing (CE) reasons, unauthorised conversion and/ or modiﬁcations

of the product are inadmissible.

e product should not be exposed to abnormal conditions, such as extreme

temperatures, direct sunlight or vibrations. Long-term exposure to chemical

vapours in high concentration can aﬀect the product performance. Make sure the

work environment is as dry as possible; avoid condensation.

All installations shall comply with local health and safety regulations and local

electrical standards and approved codes. is product can only be installed by

an engineer or a technician who has expert knowledge of the product and safety

precautions.

Avoid contacts with energised electrical parts. Always disconnect the power

supply before connecting, servicing or repairing the product.

Always verify that you apply appropriate power supply to the product and use

appropriate wire size and characteristics. Make sure that all the screws and nuts

are well tightened and fuses (if any) are ﬁtted well.

Recycling of equipment and packaging should be taken into consideration and these

should be disposed of in accordance with local and national legislation/regulations.

In case there are any questions that are not answered, please contact your

technical support or consult a professional.

www.sentera.eu

MIW-RTR-1-EN-000 - 12 / 04 / 2021 4 - 8

back to the table of contents

RTR-1 REMOTE SWITCHED 230 VAC

TRANSFORMER CONTROLLER

PRODUCT DESCRIPTION

e RTR-1 series of transformer fan speed controllers regulate the rotational speed

of single-phase voltage controllable motors by varying the output voltage. ey

are equipped with an auto-transformer and control the speed manually in steps

via a remote device, e.g. a switch or thermostat. e technology used provides a

regulated output voltage with a perfect sinusoidal shape.

ARTICLE CODE

Article code Rated max. current, [A] Fuse rating

RTR-1-15L22 1,5 (5*20 mm) T-3,15 A-H

RTR-1-25L22 2,5 (5*20 mm) T-4,0 A-H

RTR-1-35L22 3,5 (5*20 mm) T-5,0 A-H

RTR-1-50L22 5,0 (5*20 mm) T-8,0 A-H

RTR-1-75L22 7,5 (6*32 mm) T-12,5 A-H

INTENDED AREA OF USE

■Fan speed control of voltage controllable motors (pumps and fans) in ventilation

systems

■For indoor use only

TECHNICAL DATA

■Supply voltage: 230 VAC / 50—60 Hz

■Unregulated output: 230 VAC / 2 A

■Remote fan speed control via external device (e.g. Sentera’s SMT-1-30-4C switch)

■Transformer taps directly connected to the terminal block

■Enclosure: plastic (R-ABS, UL94-V0, grey RAL 7035)

■Protection standard: IP54 (according to EN 60529)

■Operating ambient conditions:

►Temperature: -20—35 °C

►Rel. humidity: 5—95 % rH (non-condensing)

STANDARDS

■Low Voltage Directive 2014/35/EC

■EMC Directive 2014/30/EC: EN 61326

■WEEE Direc tive 2012/19/EC

■RoHs Directive 2011/65/EC

www.sentera.eu

MIW-RTR-1-EN-000 - 12 / 04 / 2021 5 - 8

back to the table of contents

RTR-1 REMOTE SWITCHED 230 VAC

TRANSFORMER CONTROLLER

OPERATIONAL DIAGRAM

Operational diagram

Regulated output (U)

Unregulated output (L)

Input from

external device

0123 45

230

190

170

140

110

U [VAC]

WIRING AND CONNECTIONS

L Power supply, line (230 VAC / 50—60 Hz)

NPower supply, neutral

LUnregulated output, line

L1 Not connected

NUnregulated output, neutral

Regulated output to motor, neutral

U Regulated output to motor, line

PExternal switch, common

External switch, positions

ATTENTION Make sure you use cables with an appropriate diameter.

MOUNTING INSTRUCTIONS IN STEPS

Before you start mounting the unit, read carefully “Safety and Precautions”.

Choose a smooth solid surface for installation (a wall, panel, etc.).

Follow these steps:

1. Unscrew the front cover and open the enclosure.

2. Fix the unit onto the wall or panel using the provided screws and dowels. Mind the

correct mounting position and unit mounting dimensions. (See Fig. 1 Mounting

dimensions and Fig. 2 Mounting position.)

3. Pay attention to the following instructions in order to minimize the operating

temperature:

3.1 Respect the distances both between the wall / ceiling and the device and

www.sentera.eu

MIW-RTR-1-EN-000 - 12 / 04 / 2021 6 - 8

back to the table of contents

RTR-1 REMOTE SWITCHED 230 VAC

TRANSFORMER CONTROLLER

between two devices as shown in Fig. 2. In order to ensure suﬃcient

ventilation of the controller, clearance on every side has to be maintained.

3.2 When installing the device, please keep in mind that the higher you install

it, the warmer the device will get. For example, in a technical room the

correct installation height can be of great importance.

3.3 If maximum ambient temperature cannot be adhered to, please provide

extra forced ventilation / cooling.

Not respecting the abovelisted rules can reduce service life and relieves the

manufacturer of any responsibilities.

Fig. 1 Mounting dimensions Fig. 2 Mounting position

Article code A

[mm] B

[mm] C

[mm] D

[mm] E

[mm]

RTR-1-15L22 170 255 140 155 194

RTR-1-25L22 170 255 140 155 194

RTR-1-35L22 170 255 140 155 194

RTR-1-50L22 170 255 140 155 194

RTR-1-75L22 200 305 140 183 236

Correct Incorrect

50 mm50 mm

75 mm

50 mm

Wall

4. Insert the cables through the cable glands and do the wiring according to the

wiring diagram (see Fig. 3) while adhering to the information from section

“Wiring and connections” above.

4.1 Connect the power supply line (terminals L, N and protective earth).

4.2 Connect the motor(s) (terminals U, N and protective earth).

4.3 Connect the external switch (e.g. Sentera’s SMT-1-30-4C) (terminals P and

1, 2, 3, 4, 5 as indicated in Fig. 3 below)

4.4 If applicable, connect the unregulated output (L and N). It can be used to

supply a 230 VAC valve, lamp, etc. e unregulated output is active when

the supply voltage is present.

ATTENTION A safety isolator / disconnect switch should be installed on the mains electricity

side of all motor drives.

www.sentera.eu

MIW-RTR-1-EN-000 - 12 / 04 / 2021 7 - 8

back to the table of contents

RTR-1 REMOTE SWITCHED 230 VAC

TRANSFORMER CONTROLLER

Fig. 3 Wiring diagram

230 VAC

OUT

230 VAC

LL NL1

N U

P 12

External device - SMT-1-30 - 4C

common

ATTENTION Make sure the connections are correct before you power the unit.

5. Close the cover and secure it with the screws.

6. Tighten the cable glands.

7. Switch on the mains supply.

8. e controller needs to be switched on via the external switch.

9. Make sure the transformer controller can operate normally (consider an isolating

switch).

10. Turn the external switch into the relevant positions to adjust the output voltage.

Optional settings

e standard conﬁguration of the output voltages is as indicated in Table 1 below.

Table 1 Voltage series

Wires -

Regulated output [VAC]

Output voltage** 080*110 140 170 190 230

Unregulated output [VAC]

L230 230 230 230 230 230 230

*Available but not connected.

** Because more than 5 output voltages are available, it is possible to adjust the

steps by changing the internal wiring.

VERIFICATION OF INSTALLATION

ATTENTION A safety isolator / disconnect switch should be installed on the mains electricity

side of all motor drives.

Safe operation depends on proper installation. Before start up, ensure the following:

■e mains supply is connected correctly.

■Protection is provided against electrical shock.

■e cables are the appropriate size and fuse-protected.

■ere is suﬃcient air ﬂow around the unit.

www.sentera.eu

MIW-RTR-1-EN-000 - 12 / 04 / 2021 8 - 8

back to the table of contents

RTR-1 REMOTE SWITCHED 230 VAC

TRANSFORMER CONTROLLER

ATTENTION e unit is supplied with electrical energy at voltages high enough to inﬂict personal

injury or threat to health. Take the relevant safety measures.

ATTENTION Disconnect and conﬁrm that there is no live current ﬂowing to the unit before servicing.

ATTENTION Avoid exposing the controller to direct sunlight!

TRANSPORT AND STORAGE

Avoid shocks and extreme conditions; stock in original packing.

WARRANTY AND RESTRICTIONS

Two years from the delivery date against defects in manufacturing. Any modiﬁcations

or alterations to the product after the date of publication relieve the manufacturer

of any responsibilities. e manufacturer bears no responsibility for any misprints or

mistakes in this data.

MAINTENANCE

In normal conditions this product is maintenance-free. If soiled, clean with a dry or

damp cloth. In case of heavy pollution, clean with a non-aggressive product. In these

circumstances the unit should be disconnected from the supply. Pay attention that

no ﬂuids enter the unit. Only reconnect it to the supply when it is completelydry.

Inhaltsverzeichnis

Andere Sentera Controls Controller Handbücher

Sentera Controls

Sentera Controls RMFPX-2R Service-Handbuch

Sentera Controls

Sentera Controls GTTE1 Service-Handbuch

Sentera Controls

Sentera Controls STVS1 Series Service-Handbuch

Sentera Controls

Sentera Controls RMFPM-2R Service-Handbuch

Sentera Controls

Sentera Controls GTT-1 Service-Handbuch

Sentera Controls

Sentera Controls MTY-0-05-AT Service-Handbuch

Sentera Controls

Sentera Controls EVSS1 Series Service-Handbuch

Sentera Controls

Sentera Controls STRS1 Series Service-Handbuch

Sentera Controls

Sentera Controls RTVS8 Series Service-Handbuch

Sentera Controls

Sentera Controls AH2A1-6 Service-Handbuch

Sentera Controls

Sentera Controls SD Service-Handbuch

Sentera Controls

Sentera Controls MTP-D010 Series Service-Handbuch

Sentera Controls

Sentera Controls MCS-1-LCD Service-Handbuch

Sentera Controls

Sentera Controls SER-1 Series Service-Handbuch

Sentera Controls

Sentera Controls TCMF8-WF Series Service-Handbuch

Sentera Controls

Sentera Controls HPSPX-2 Service-Handbuch

Sentera Controls

Sentera Controls ECMF8-EW Service-Handbuch

Sentera Controls

Sentera Controls GTEX1-60-DM Service-Handbuch

Sentera Controls

Sentera Controls SDX-DM Series Service-Handbuch

Sentera Controls

Sentera Controls DRPUM Service-Handbuch

Sentera Controls

Sentera Controls MT Service-Handbuch

Sentera Controls

Sentera Controls RDCV Service-Handbuch

Sentera Controls

Sentera Controls ECA-1-10-AC Service-Handbuch

Sentera Controls

Sentera Controls HPSPX-LP Service-Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung