Sentera Controls DIGWM Bedienungsanleitung
USER GUIDE
HOW TO CONNECT THE INTERNET GATEWAY
TO THE WI-FI NETWORK
www.sentera.eu
UserGuide - 07 / 09 / 2021 2 - 4
back to the table of contents
HOW TO CONNECT THE INTERNET
GATEWAY TO THE WI-FI NETWORK
ARTICLE CODES
is document explains how a Sentera internet gateway can be connected to a local -
Wi-Fi network. is document applies to following article codes:
■DIGWM
■SIGWM
■DIG-M-2*
■SIG-M-2*
*e DIG-M-2 and SIG-M-2 Internet Gateways can also be hard wired to your router. In that case, use a regular network
cable en skip the Wi-Fi setup below. Go direct to SenteraWeb setup at the end of this document.
CONNECT THE INTERNET GATEWAY TO THE WI-FI NETWORK
■Connect the power supply
■By default, the red LED of the internet gateway lights up. is indicates that
there is no connection with the Wi-Fi network
■To adjust the settings of the internet gateway, proceed as follows:
►Using your computer or mobile device, scan for available Wi-Fi networks (see
Fig. 1)
►Connect to the Sentera Internet Gateway (XIGxM-xxxxxxxxxx) using the
password “123456789”
Fig. 1
www.sentera.eu
UserGuide - 07 / 09 / 2021 3 - 4
back to the table of contents
HOW TO CONNECT THE INTERNET
GATEWAY TO THE WI-FI NETWORK
■Open the internet browser of your mobile device or computer and enter following
ur l: “192.16 8.1.123”
■is brings you to the internal host page of the Sentera Internet Gateway (See
Fig. 2)
■Check the Wi-Fi box
■Select the Wi-Fi network to which you want to connect your Gateway
■Enter the password of the selected Wi-Fi network
■Click “Save & Restart”
■Now your internet gateway is connected to the Wi-Fi network. e green LED
lights up
■e internal host page is no longer available. If something goes wrong or if you
want to select a different Wi-Fi network, press the Wi-Fi reset button for 5
seconds and restart this procedure.
Fig. 2
www.sentera.eu
UserGuide - 07 / 09 / 2021 4 - 4
back to the table of contents
HOW TO CONNECT THE INTERNET
GATEWAY TO THE WI-FI NETWORK
OPEN SENTERAWEB
Now everything is ready to set up your installation via SenteraWeb.
Remember that you need the serial number of each product that you want to connect
to your installation!
Follow these steps:
1. Create your account on SenteraWeb
2. Log in via: https://www.senteraweb.eu/en/Account/Login
3. Create your installation by entering the serial number of the Gateway
4. Make sure that all devices that you want to add to your installation are powered
and connected (Via Modbus RTU) to the Master channel of the Sentera Internet
Gateway
5. Now you can start adding the slave devices to the installation by entering their
serial numbers
Fig. 3
ATTENTION Make sure that the device(s) that you want to add to your SenteraWeb installation
have Modbus ID 1 (factory default).
ATTENTION SenteraWeb will assign a new Modbus ID to the device when you add it to your
installation, and put it back to 1 when you remove the device from your installation.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Sentera Controls Tor Handbücher
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
