ESM40-C480DN_ESM40-C420-OSD_ESM34-C420DN_rev011909
Model ESP12-C4243ADN ESP12-C4243ADNP ESP016-C4237ADN ESP016-C4237ADNP ESP16-C4237ADN ESP16-C4237ADNP
Signal Format NTSC PAL NTSC PAL NTSC PAL
Image Sensor 1/4” Sony CCD 1/3” Sony CCD
Resolution 420 TV Lines
Effective
Pixels 510(H)x492(V) 500(H)x582(V) 510(H)x492(V) 500(H)x582(V) 510(H)x492(V) 500(H)x582(V)
Scanning
System 525 Lines
60 field/sec. 625 Lines
50 field/sec. 525 Lines
60 field/sec. 625 Lines
50 field/sec. 525 Lines
60 field/sec. 625 Lines
50 field/sec.
Sync Mode Internal Synchronization
S/N Ratio More than 48dB (AGC Off)
Gamma
Characteristic 0.45
Minimum
Illumination 0.5 Lux (Day) / 0.05 Lux (Night)
Gain Control Auto
BLC Auto
White
Balance Auto
Electronic
Shutter
Speed
1/60~1/100,000
sec. 1/50~1/100,000
sec. 1/60~1/100,000
sec. 1/50~1/100,000
sec. 1/60~1/100,000
sec. 1/50~1/100,000
sec.
Day & Night Yes
Lens 4.3mm Supercone Pinhole Lens 3.7mm Supercone Pinhole Lens
Video Output 1Vp-p, 75 Ohms, Negative
Audio Output 300mV @ 600 Ohms
Power Supply 12V DC, 10% / 100mA
Operating
Temperature 14°F~122°F / -10°C~50°C, RH 95% Max.
Storage
Temperature -4°F~140°F / -20°C~60°C, RH 95% Max.
Dimensions
of Camera 0.47”(W) x 0.47”(L)
12(W) x 12(L) mm (Ø)0.63” / (Ø)16 mm 0.63”(W) x 0.63”(L)
16(W) x 16(L) mm
*Specifications are subject to change without notice
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this may damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could damage the camera.
3. Requires a proper operating environment
The allowable temperature range for operation of this camera is between 14°F~122°F / -10°C~50°C and the allowable humidity level is below 95%. Do not expose
the camera to rain or moisture. Do not try to operate the camera in wet area. Moisture can damage the camera and can cause electric shock.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before lens installation or whenever the lens is changed. Cleaning should be done by using a
chamois, a very fine soft cloth, lens tissue, or cotton tipped applicator and ethanol to carefully remove any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range. (Camera must meet the specifications). Camera must be connected to a surge protector at all
times. It is recommended that you use a regulated 12V DC power supply with camera for best picture quality and for safe operation of the unit. Unregulated 12V
DC power supply usually provides around 17~20V after loaded, and can cause damage to the camera.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch dangerous voltage points of short out parts that could result in a fire or electric shock. Never
spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all service
to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
d. If the video product has been dropped or the cabinet has been damaged.
e. When the video product exhibits a distinct change in performance.
9. Use a suitable monitor
Use a monitor which has the standard video input impedance level of 75 ohms.Ifinany case your monitor is set to high impedance mode, please switch the monitor
to the standard impedance position.
CAUTION
SPECIFICATIONS
P = PAL Version
