Sentry NC-GSMDE263 Benutzerhandbuch

GSM Intercom Door / Gate Entry System

NC-GSMDE263

System Installation, Setting and Operation Manual

User Manual (NC-GSMDE263)

Please read this user manual completely before operating this system and keep it in a safe place for future reference.

TABLE OF CONTENTS

TABLE OF CONTENTS …………………………………………………………….

IMPORTANT SAFETY INSTRUCTIONS…………………………………………..

SYSTEM DIAGRAMS

Front View ……………………………………………………………………….

Back View ……………………………………………………………………….

Wall Mounting Bracket ………………………………………………………….

INSTALLATION

GSM Intercom Door / Gate Entry System……………………………………..…

Wiring Diagram & Wiring Instructions ……………………………………….....

OPERATION

Power ON/OFF …………………………………………………………………..

Manager Mode and Functions ……………………………………………………

Button Functions …………………………………………………………………

MANAGER SETTINGS

Change Manager Password ………………………………………………………

Store Manager Telephone Number ……………………………………………....

Set Minutes for Talk Time ……………………………………………………….

GSM SETTING

Change GSM Password ………………………………………………………….

Change Microphone Volume …………………………………………………….

Change Speaker Volume ……………………………………………………........

Change Speaker Volume During Conversation ………………………………….

DOOR SETTING

To Activate / Deactivate Door Strike by Password ………………………………

Change Opening Door Password …………………………………………………

Door Opening Time ………………………………………………………………

SUBSCRIBER ID NUMBER SETTING

Setup Subscriber ID Number …………………………………………………….

Enable or Disable the Subscriber ID Number ……………………………………

CONTACTINGA SUBSCRIBER...………………………………………………….

OPEN THE DOOR REMOTELY …………………………………………………..

GO BACK TO “WELCOME!” SCREEN AUTOMATICALLY ………………….

SIM CARD ……………………………………………………………………………

CALLMANAGER …………………………………………………………………..

MASTER RESET…………………………………………………………………….

1~2

Thank you for purchasing the GSM Intercom Door / Gate Entry System. To ensure that you enjoy the full

capacity of this product, please read this user manual before proceeding. Be sure to keep this manual for future

reference in case any challenge or question should arise. We hope you enjoy your new GSM Intercom Door /

Gate Entry System.

IMPORTANT SAFETY INSTRUCTIONS

When using your GSM Intercom Door / Gate Entry System, basic safety precautions should always be followed

to reduce the risk of fire, electric shock and personal injury. Please read the following before using your

equipment.

1. Follow all warnings and instructions on the product.

2. Unplug the product before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

3. Do not use this product near water.

4. Do not allow anything to rest on power cords. Do not place this product in a location where the cords can be

stepped on or where someone can trip over them.

5. Do not use this product near an area where there is a potential of gas leaks or near any fumes that can be

explosive.

6. Do not place this equipment near or over a radiator or any other heat source.

7. Use ONLY the power adapter supplied with the system.

8. Do not overload the wall outlet or power cord where the power adapter is installed. This can result in fire or

electric shock.

9. This equipment is to be opened ONLY by a qualified service technician. There are no user serviceable parts

inside. Opening this equipment may expose you to dangerous voltage and other risks. Incorrect reassembly

of this equipment may result in electric shock.

10. Avoid spilling liquid on this equipment and do not insert any objects through the ventilation slots.

11. Avoid using this equipment during an electrical storm. There is a remote risk of electrical shock from

lighting.

12. Do not use this equipment other than for its purpose intended by the manufacture. Use ONLY the equipment

provided by the manufacturer.

System Diagram (Front View)

System Diagram (Back View)

System Diagram (Wall Mounting Bracket)

INSTALLATION

GSM Intercom Door / Gate Entry System

1. Take the wall mount bracket from the package and screw it on proper place. (As shown in Step 1 &

2 below)

2. Open the bottom cover of door unit and pass the wires through wire-hole. Then, refer to the

“Wiring Diagram and Wiring Instruction” to connect wires and insert the SIM card to SIM card

slot. (As shown in Step 3)

3. Put the bottom cover back. (As shown in Step 4)

4. Place door unit on the fixed wall mount bracket. (As shown in Step 6 & 7)

5. Put the acrylic cover on the door unit when door unit has been screwed. (As shown in Step 8 & 9)

6. Plug the AC adapter into the AC outlet; the door unit will go into standby condition.

WARNING: Only use the original power adapter supplied. Using any other adapter might damage the

door unit and cause a risk of electric shock.

Wiring Instructions

1. System Power Supply Wiring

The system power supply (adapter) AC 120V or 230V / DC 13V is provided along with the system

(please note whether it can meet local voltage specification).

The negative wire is connected to Terminal Pin 1 and the positive wire is connected to Terminal

Pin 2.

2. Install Door Lock with System Power Wiring

The door lock may be powered using the system’s power supply by connecting the positive wire of

the lock to Terminal Pin 4 and the negative to Terminal Pin 5. The ACK wire, if your strike has

one, is connected to Terminal Pin 6. (The system will supply 12 volts DC at 1000 mA)

3. Install Door Lock with its own power supply Wiring

If the door lock comes with its own power supply or requires more power than this unit will

provide, the power should be connected as follows. Remove the jumper wires joining Terminal Pin

2and Terminal Pin 3. Remove the jumper wires joining Terminal Pin 1 and Terminal Pin 5 as

well. The positive wire of the power supply is connected to Terminal Pin 3 and the negative to

Terminal Pin 5.

The door lock’s positive wire is connected to Terminal Pin 4 and the negative wire is to Terminal

Pin 5. The ACK wire, if your strike has one, is connected to Terminal Pin 6.

OPERATION

zBefore operation: Please make sure the GSM Intercom Door / Gate Entry System is installed

correctly. Please also study all key functions before use.

Power ON/OFF

Turn the power ON

Insert the plug of the power adapter into the DC power jack of door unit and the other end into an

AC power outlet.

When the power is on, the system will emit a “beep” sound, show “GSM Intercom Door / Gate

Entry System” and software version on screen, “Search Network” for few second, and then show

“Welcome!"

Turn the power OFF

Turn off the door unit by unplugging the power adapter from the AC power outlet.

Manager Mode and Functions

Note: The unit will be time out after 5 seconds if no buttons are pressed.

Press the MENU button, and the system will show "Hello! Manager!" "Password:______"

After entering default password "1234", press the CALL button to show the button functions as

below:

"CALL: Select/Save"

"C: Delete"

"MENU: Exit/Abort"

"▲/▼: Move cursor"

Press any button or after 6 seconds, it will show:

GSM Door Phone

Version v1.18 Search Network

Hello! Manager! Password:

_ _ _ _

Manager

Subscriber

Welcome!

Manager Settings:

Under the Manager section, there are 3 main options: “System Setting”, “GSM Setting” and “Door

Setting”.

Change Manager Password

Manager Setting ÆSystem Setting ÆChange Password

Note: The Manager Password is the key to enter Programming Mode. Please make sure to keep the Manager Password in a

safe place. If you forget the Manager Password, you’ll have to do a Master Reset which will delete your saved phones

numbers and settings.

While at the Manager menu option, press the CALL button

Select System Setting and press the CALL button

Select Change Password and press the CALL button

Enter New password (must be 4 digits)

Enter password again to confirm and press the CALL button

Store Manager Telephone Number

Manager Setting ÆSystem Setting ÆManager Phone#

Note: This will be the number that is called when the CALL button is pressed in standby mode.

While at the Manager menu option, press the CALL button

Select System Setting and press the CALL button

Select Manager Phone # and press the CALL button

With cursor on the 1, press the CALL button to enter phone number

Enter phone number with prefix and area code, then press the CALL button to save.

(If you enter a number incorrectly, use the arrow keys to move forward or backward. The Cbutton will clear a

digit you do not want.)

Press the MENU button to return to previous options screen

System Setting

GSM Setting

Door Setting

Inhaltsverzeichnis

Andere Sentry Gegensprechanlage Handbücher

Sentry

Sentry GSM-DE3100 Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung