SGM C-1 Bedienungsanleitung

USER

MANUAL

980

C-1

WIRELESS DMX

CONTROLLER &

SGM APP

980

C-1 controller dimensions

C-1 CONTROLLER

USER MANUAL REV. C

All dimensions in millimeters and inches. Drawing not to scale.

This manual covers installation, use, and maintenance of the SGM C-1.

A digital version is available at www.sgmlight.com or upon request via [email protected].

SGM and all afliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential

or economic loss, or any other loss occasioned by the use of, inability to use, or reliance on the information

contained in this manual. The SGM logo, the SGM name, and all other trademarks in this document pertaining

to SGM services or SGM products are trademarks owned or licensed by SGM, its afliates and subsidiaries.

This edition applies to rmware version 0.98 or later.

English edition

Contents

Safety information.....................................................................................................................4

Overview .................................................................................................................................5

Parts identication and terminology ............................................................................................5

Preparing for installation............................................................................................................6

Installing the C-1.......................................................................................................................6

Connecting AC power................................................................................................................7

Conguring the C-1 ...................................................................................................................7

Connecting the P-1 to the C-1 controller.......................................................................................8

Connecting the C-1 Controller to the SGM C-1 App ........................................................................9

SGM C-1 Controller App overview - I ..........................................................................................10

SGM C-1 Controller App overview - II .........................................................................................11

SGM C-1 Controller App overview - III ........................................................................................12

SGM C-1 Controller App overview - IV ........................................................................................13

RDM......................................................................................................................................14

Troubleshooting .....................................................................................................................14

Service ..................................................................................................................................14

Fixtures and accessories .........................................................................................................15

Support hotline.......................................................................................................................15

Approvals and certications.....................................................................................................15

User Notes.............................................................................................................................16

Safety information

• Do not open the device; there are no user-serviceable parts inside.

• Ensure that the power is cut off when wiring the device to the AC mains supply.

• Ensure that the device is electrically connected to earth (ground).

• Do not apply power if the device or mains cable is in any way damaged.

• Do not immerse the xture in water or liquid.

DANGER! Risk of electric shock. Do not open the device.

Misusing the battery may cause the battery to get hot, rupture, or ignite and cause serious injury.

Be sure to follow the safety informations listed below:

• Do not place the battery in re or heat the battery.

• Do not install the battery backwards with reversed polarity.

• Do not connect the positive terminal to the negative terminal of the battery with any metal object (such as a wire).

• Do not carry or store the battery together with necklaces, hairpins or other metal objects.

• Do not pierce the battery with nails, strike the battery with a hammer, step on the battery, or otherwise subject it to strong

impacts or shocks.

• Do not expose the battery to water or salt water, or allow the battery to get wet.

• Do not disassemble or modify the battery. The battery contains safety and protection devices which, if damaged, may cause

the battery to generate heat, rupture, or ignite.

• Do not place the battery on or near res, stoves, or other high-temperature locations. Do not place the battery in direct

sunlight. Doing so may cause the battery to generate heat, rupture, or ignite. Using the battery in this manner may also

result in a loss of performance and a shortened life expectancy.

• Do not place the battery in microwave ovens, high-pressure containers, or on induction cookware.

• Immediately discontinue use of the battery if, while using, charging, or storing, the battery emits an unusual smell, feels hot,

changes color or shape, or appears abnormal in any other way.

• Only charge the battery mounted in the xture with the built-in charger. Do not use a third party charger.

• Do not charge unattended.

• Only charge the battery if the surrounding temperature is in the range of +5 to +35°C (41° to 95°F). Charging the battery

at temperatures outside of this range may cause the battery to become hot or break. Charging the battery outside of this

temperature range may also harm the performance of the battery or reduce the battery’s life expectancy.

• Do not replace the battery in the xture with other types of rechargeable batteries.

• Do not replace the battery in the xture with non-rechargeable batteries, such as dry-cell batteries etc.

• When the battery is worn out, insulate the terminals with adhesive tape or similar materials before disposal.

• Follow applicable laws and regulations for transport, shipping, and disposal of batteries. For details on recycling lithium,

lithium-phosphate, and lithium-ion batteries, please contact a government recycling agency or your waste-disposal service.

This warning applies to all SGM battery driven products due to the inside LI-ION battery.

WARNING! LI-ION Battery.

WARNING!

Read the safety precautions in this section before installing, powering, or operating

this product.

SGM luminaries are intended for professional use only. They are not suitable for household use.

Les luminaires SGM sont impropre à l’usage domestique. Uniquement à usage professionnel.

Review the following safety precautions carefully before installing or operating the device.

C-1 Controller is a wireless and very compact device designed to program the SGM P-1 luminaire, and can be congured and

controlled through a smart-phone or a tablet application. With a single DMX universe via Wireless DMX (CRMX), the C-1 enables the

user to congure and programme scenes via the SGM C-1 App.

The free SGM App offers a wireless DMX controller solution for both Android and iOS, giving the user a variety of control and

programming possibilities related to the SGM P-1.

Both C-1 Controller and C-1 App are designed to complement SGM’s P-1 luminaires. By using both features, the user can remotely

prepare the light setting for any environment, while grouping, naming, and organizing P-1 light xtures as preferred, and storing an

unlimited amount of scenes in a simple and straightforward way.

All personalized settings are saved in the C-1 Controller to enable simultaneous control of multiple SGM P-1 devices.

Overview

Parts identication and terminology

Wiﬁ

On/Oﬀ

Connect 3sec

Wiﬁ Reset 10 sec

Box Reset 20 Sec

CRMX

*Front view

*Back view

*Top view

A: CRMX LumenRadio antenna D: Funcon buon G: Pressure valve

B: Wiﬁ antenna E: Status indicator

C: On/Oﬀ buon F: Power cable

Figure 1: C-1 parts and terminology

Fasten a safety cable between the support structure and the attachment point on the device (as shown).

The safety cable must be able to bear at least 10 times the weight of the device (SWL) and

have a minimum gauge of 2 mm.

CAUTION!!

• Always use a safety wire.

• Min. safety wire gauge = 2 mm.

• Max. safety wire length (free fall) = 15 cm (12 in.)

• Make sure the slack of the safety wire is at a minimum.

Safetywire

WARNING! Always secure an elevated C-1 with a safety cable

The C-1 may be installed in any orientation and in any environment due to the IP65-rated enclosure. The C-1 may operate resting on

a surface or hanging. For elevated operation, install a clamp by installing a T-bolt and clamp of corrosion-resistant material suitable

for the location.

Installing clamp for elevated operation

Installing the C-1

Safetywire

M10 T-bolt

Use only corrosion-resistant mechanical fasteners suitable for the locaon.

Insert the M10 T-bolt, turn it clockwise to lock rotaon. Insert washer and mount the clamp.

Insert locknut and turn the clamp cloxkwise to ghten the clamp securely down against the chassis.

Aach a safetywire.

456

Insert the M10 T-bolt in the slot. Turn the bolt clockwise to lock rotation. Insert washer.

Mount the clamp (any clamp works) Lock the clamp with a locknut min. grade 8.8. Turn the clamp clockwise to tighten the clamp

against the chassis. Attach safetywire.

Safetywire

Unpack the device and inspect it to ensure that it has not been damaged during transport.

When selecting a location for the device, ensure that:

• It is situated away from public thoroughfares, and protected from contact with people

• It has adequate ventilation

• It is not immersed in water or exposed to high-pressure water jets

The C-1 is IP65-rated and designed for use in both indoor and outdoor events. This means that it is protected from:

• Smoke uid, dust, dirt, and airborne pollution to the degree that they cannot enter the device in sufcient quantities so as to

interfere with its operation

• Humidity and lower pressure jets of water from any direction

Download the SGM C-1 App from App Store or Google Play Store.

Note: the purpose of the C-1 controller is only to be used with the SGM IP65-rated battery driven P-1 RGBW LED Wash light.

Transportation

Always use the supplied packaging or suitable case for transportation and storage of the C-1 controller.

Never carry the xture by the cable.

Preparing for installation

Figure 2: Installing the C-1

Figure 3: C-1 safety wire

The C-1 is a battery-driven product that can operate on any 100–240 V, 50/60 Hz AC mains power supply. It draws approximately

0.2A when charging.

For permanent installations, have a qualied electrician wiring the mains cable directly to a suitable branch circuit. The junction’s

ingress protection (IP) rating must be suitable for the location. For outdoor installations, the mains cable may be tted with a grounded

connector intended for exterior use.

The power cable color coding is the following:

• Connect the black wire to live

• Connect the white wire to neutral

• Connect the green/yellow wire to ground (earth)

The device must be grounded/earthed and be able to be

isolated from AC power when connected. The AC power supply must incorporate a fuse or circuit breaker for fault protection. For

assistance with alternative congurations, contact your SGM representative.

CAUTION!!

Do not open the xture to replace the supplied power cable, or connect the xture to an electrical dimmer system, as doing so may

cause damage. Ensure that the mains power is off when wiring the xture to AC mains supply.

Always power off/unplug the xture before removing covers or dismantling the product.

PLEASE NOTE!!

When connected to AC Power, the C-1 starts transmitting Wi-Fi and Wireless DMX (CRMX) to any previous linked products.

Connecting AC power

Color

Black

White

green/yellow

Conductor

live

neutral

ground (earth)

Symbol

Wire

On/Off button (A)

Push On/Off button to turn on/off the device. When turned on, the LED status will

switch to orange color. Then wait 10 to 30 seconds until the C-1 congures its

internal Wi-Fi connection. When ready, the LED status will change from orange

to green. To power off the device make sure to press the same button longer

than 3 seconds.

Function button (B)

This button is used for the three functions below:

• Connecting a xture - Press and hold the button for 3 seconds

to connect unlinked xtures to the C-1 controller. If any xtures are

paired with another transmitter, the xtures must be unlinked rst from

wireless DMX. When the P-1 is connected, the device will automatically

get information via RDM to set the correct address and DMX mode to

be controlled via the SGM C-1 App.

The C-1 will send commands until all xtures connected are correctly addressed and have the correct mode. All available

xtures can be seen in the C-1 App (see how in “Fixture view” on page 10). Please note that when the xture is in any

other mode than DMX, it is not possible for the C-1 controller to make use of the auto addressing and mode function.

When connected, the C-1 will automatically retransmit DMX address and mode to all xtures, and collect sensor data every

90 seconds. This means that if any xture was connected (and tampered) to a C-1 controller, it will restore the correct DMX

address and mode. Please note that this will not apply to operation mode. If the mode has been changed, it has to be set

again to DMX to receive CRMX.

• Wi-Fi Reset - Press and hold the button for 10 seconds to reset the Wi-Fi function. The status LED will blink yellow/or-

ange during reset. This function resets the Wi-Fi password to default Wi-Fi password: sgm12345. This function is useful for

restoring the Wi-Fi settings and clear passwords saved on mobile devices.

• Box Reset - Press and hold the button for 20 seconds to reset the C-1 controller. The status LED will blink red during reset.

This function resets Wi-Fi and reconnects all wireless devices saved/visualised in the SGM C-1 App.

NOTE!!

To remove a xture from the C-1 controller, nd the xture in the SGM C-1 App and delete it. See how in “Fixtures”, on page 11.

The C-1 is controlled exclusively by the SGM C-1 App. The app is free and available for download in App Store and Google Play

Store.

Conguring the C-1

Figure 4: Connecting AC Power

Wiﬁ

On/Oﬀ

Connect 3sec

Wiﬁ Reset 10 sec

Box Reset 20 Sec

CRMX

A B C

A: On/Oﬀ buon

B: Funcon buon

C: LED Status indicator

Figure 5: Conguring the device

LED Status indicator (C)

The C-1 controller has a status diode to show the current state or function.

The P-1 is controllable due to the C-1 inbuilt RDM (Remote Device Management) auto setting, which ensures the DMX address is set

when connected to the C-1. The P-1 connects to the C-1 via the LumenRadio CRMX wireless receiver system. When using the C-1

wireless DMX system, ensure that the DMX chassis connectors are properly covered.

Connecting the SGM C-1 controller

The P-1 is designed to look for wireless transmitters in “connect” state, when not already paired to one. If a P-1 has previously been

connected to the C-1 controller, it will appear in the SGM C-1 App due to its unique RDM ID, which it is stored in the C-1 controller.

This means that a single P-1 can be left out in one event, and put back in another without loosing its DMX address and all stored

scenes.

Note that any previously connected device stored in the C-1 is occupying the DMX slots. To remove the xture(s) and release the

DMX slots, please use the SGM C-1 App (see how on page 11). There is no button function to remove a stored xture directly from

the C-1 controller.

Connecting the P-1 to the C-1 controller

Auto addressing and mode setting

When the P-1 is connected, the device will automatically get information via RDM to set the correct address and DMX mode to be

controlled via the SGM C-1 App. The C-1 Controller will send commands until all connected xtures are addressed correctly and are

in the right mode. All available xtures can be seen in the SGM C-1 App (see on page 11).

Please note that if the xture is in any other mode than DMX it is not possible for the C-1 controller to make use of the auto addressing

and mode function.

Disconnecting a P-1 from any wireless transmitter

To disconnect the xture from any currently paired wireless transmitter:

• Go to MENU → SETTINGS → WIRELESS DMX → LOG OFF.

Shortcut to unlink a P-1 from any transmitter

ESC + DOWN: “Press ‘ENTER’ to unpair CRMX”

• Ensure the P-1 device(s) is/are logged off any wireless transmitter and not in any

manual mode.

• Push and hold the function button of the C-1 controller for 3 seconds to connect the

unlinked xtures to the C-1 controller. If any xture is paired with another transmitter,

the xture must rst be unlinked from wireless DMX.

• Conrm that the xture is paired with the wireless transmitter, going to MENU →

SETTINGS → WIRELESS DMX → STATUS (see gure 9).

• After approx. 90 seconds the xtures should be addressed and ready for operation.

Connecting the P-1 to the C-1 controller

ESC ENTER

Press Enter to

Unpair CRMX

ESC ENTER

SIGNAL STRENGTH: 96%

CRMX PAIRD: YES

DMX Active : YES

Static green

Status OK and operating normally

Static yellow/orange

Startup, reset or low battery

Static red

Error

Blinking green

Connecting CRMX

Blinking yellow/orange

Resetting Wi-Fi

Blinking red

Resetting box

Figure 6: LED Status indicator

Figure 7: Wireless DMX status

Figure 8: Disconnect the xture from wireless transmitter

Please note:

Any previous connected devices that are no longer connected are occupying a DMX slot for one xture.

Any P-1 can still get the DMX address changed via the display and therefore be connected but not receiving DMX. To send

and re-transmit the RDM information stored in the C-1, simply powercycle the C-1.

The C-1 Controller generates a local Wi-Fi hotspot to be connected to the SGM C-1 App through any smart-phone or tablet.

The SGM C-1 App is a user interface and all data, settings, scenes programmed, and connected devices are stored in the C-1

controller.

When using the SGM C-1 App, the Wi-Fi range is restricted to approx. 6m. (18 ft.) in line-of-sight. The CRMX range is depending on

the environment, capable of ranges up to 100m. The CRMX is wireless DMX based on the standard DMX 512-A, and is fully RDM

compatible, which means that the connected P-1 xtures can return valuable sensor data to the SGM C-1 App.

Take the following steps to connect the SGM C-1 App to the C-1 Controller:

• Search for the SGM C-1 App in the Play Store (Android) or App Store (iOS) of your smartphone or tablet and an SGM A/S

App will appear.

• Download the SGM C-1 App on your smartphone or tablet. Make sure you have enough space on your device to install and

run the App.

• Before opening the SGM C-1 App, go to Wi-Fi settings on your smart device.

• Disconnect your smart device from any Wi-Fi connections. For a better operation, we recommend not only to disconnect but

also to forget any Wi-Fi networks. This way your device will be connected only to the C-1 controller, ensuring the control of

the luminaires.

• Select the network with the name “SGM C-1”. You will also see 4 numbers/letters in the name of the network. These will vary

depending on the C-1 device you are using.

• Type the 8-digit password “sgm12345” to establish connection between the C-1 controller and the app (it is possible to

change the default password in the app - see page10). Now the smart device should be connected to the C-1 Controller’s

Wi-Fi network.

• Open the SGM C-1 App on your smart device. You will be able to see the P-1 xture(s) connected. A picture will appear and

also the names “Fixture XX” where “XX” indicates the DMX number.

The next pages will show in detail the menu and all SGM C-1 App features.

Connecting the C-1 Controller to the SGM C-1 App

Signal priority

The P-1 can be paired to an active C-1 Controller simultaneously as being connected to

cabled DMX. The xture will prioritize cabled DMX over wireless DMX.

The operation mode is displayed under the wireless signal strength indicator.

Please note that this will not apply to manual operation mode. To receive CRMX, the xture

has to be set to DMX mode. Any of the modes shown in the pictures on the right will override

the C-1 controller.

When in doubt about the current operation mode, restore the P-1 to factory defaults settings

by using the shortcut ESC+ENTER, and then conrm. By doing this the P-1 will set the cor-

rect DMX address and mode when connected to the C-1 controller.

ESC ENTER

QUICK

(26)

ESC ENTER

PROGRAM

Figure 9: Signal priority

SGM C-1 Controller App overview - I

The SGM C-1 app is a simple and easy feature to program and congure the C-1 Controller. This overview is a basic explanation of the

user interface.

Installing the SGM C-1 controller app

Install the Application

Download the free application

from App Store or Google Play

Store.

The app will work on any smart-

phone or tablet.

The app only works with the C-1

controller.

No Controller Found

This screen appears when the

connection to the controller is lost

or not available.

Ensure the smart-phone or tablet

is connected to the Wi-Fi hotspot,

and make sure to be within range

of the Wi-Fi hotspot (approx. 6m).

Wireless Settings

Allows the user to change the C-1

Wi-Fi password.

The new password must be

between 4 and 15 characters

long, and must contain at least

one number and one letter. It must

not contain special characters.

The password can be restored to

default doing a Wi-Fi reset (see

how on page 7). Default Wi-Fi

password is sgm12345.

Launch Screen

When launching the app, ensure

the smart-phone or tablet is

connected to the SGM C-1

Wi-Fi hotspot, and make sure to be

within range of the Wi-Fi hotspot

(approx. 6m).

Menu (general settings)

In the top left corner of the main

view, you can access the menu for

general settings of the app.

It is also possible to see how many

xtures are connected, the C-1

rmware version, and the C-1 bat-

tery indicator.

Clear user data option restores

all standard scenes, groups, and

boards. It also removes the data of

the devices previously connected to

the C-1 controller.

Advanced Options

It displays the current C-1 rmware

and hardware versions, the battery

level (%), the type of power used for

the C-1, current app version, and

the Wi-Fi hotspot details.

The advanced options also includes

a Battery Extension feature for P-1

luminaires connected from 0 to 24h.

Please note: All information upon the SGM C-1 Controller App is subject to change without notice.

Inhaltsverzeichnis

Andere SGM Controller Handbücher

SGM

SGM C5 Bedienungsanleitung

SGM

SGM Studio 12 Bedienungsanleitung

SGM

SGM TLD-612A Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung