Sharp MX-M182 Bedienungsanleitung

INSTALLATION MANUAL

Parts marked with “ “ are important for maintaining the safety of the set.

Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

MX-M232D

MX-M202D

MX-M182D

MX-M182

(With optional SPF/RSPF installed)

DIGITAL MULTIFUNCTIONAL

SYSTEM

MX-M182

MX-M182D

MX-M202D

MX-M232D

CODE : 00ZMXM182/I2E

MODEL

[ 1 ] GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

[ 2 ] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

[ 3 ] MX-M232D/MX-M202D/MX-M182D/MX-M182. . . . . . . . . . . . . . 3-1

[ 4 ] AR-SP10/AR-RP10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

[ 5 ] AR-D36/AR-D37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

[ 6 ] MX-FX13/MX-XB17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

[ 7 ] MX-NB12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

[ 8 ] MX-TR10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

[ 9 ] MX-EB14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

[10] MX-PK10 PS3 EXPANSION KIT. . . . . . . . . . . . . . . . . . . . . . . . 10-1

[11] CHANGING THE COPY PAPER SIZE IN THE TRAY. . . . . . . . 11-1

[12] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

CONTENTS

Disconnect the AC cord before servicing the unit. LASER WAVE - LENGTH : 785 15mm

Pulse times : 10.34Ǵsr0.1Ǵs/7mm㧧MX-M182,MX-M182D,MX-M202D

8.665Ǵsr0.1Ǵs/7mm㧧MX-M232D

Out put power : Max.0.3mW

MX-M232D (GENERAL) 1 - 1

[1] GENERAL

1. Note for servicing

Pictogram

The label ( ) in the fusing area of the machine indicates the

following:

: Caution, risk of danger

: Caution, hot surface

A. Warning for servicing

•The fusing area is hot. Exercise care in this area when removing misfed

paper.

•Do not disassemble the laser unit. Do not insert a reflective material

such as a screwdriver in the laser beam path.

It may damage eyes by reflection of laser beams.

B. Cautions for servicing

•Do not switch the machine rapidly on and off. After turning the machine

off, wait 10 to 15 seconds before turning it back on.

•Machine power must be turned off before installing any supplies.

•Place the machine on a firm, level surface.

•Do not install the machine in a humid or dusty location.

•When the machine is not used for a long time, for example, during

prolonged holidays, turn the power switch off and remove the power

cord from the outlet.

•When moving the machine, be sure to turn the power switch off and

remove the power cord from the outlet.

•Do not cover the machine with a dust cover, cloth or plastic film while

the power is on. Doing so may prevent heat dissipation, damaging the

machine.

•Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous laser radiation

exposure.

•The socket-outlet shall be installed near the machine and shall be easily

accessible.

C. Note for installation place

Improper installation may damage the machine. Please note the

following during initial installation and whenever the machine is moved.

Caution : If the machine is moved from a cool place to a warm place,

condensation may form inside the machine. Operation in this

condition will cause poor copy quality and malfunctions. Leave

the machine at room temperature for at least 2 hours before

use.

Do not install your machine in areas that are:

•damp, humid, or very dusty

•poorly ventilated

•exposed to direct sunlight

•subject to extreme temperature or humidity changes, e.g., near an air

conditioner or heater.

The machine should be installed near an accessible power outlet for

easy connection and disconnection.

Be sure to connect the power cord only to a power outlet that meets the

specified voltage and current requirements. Also make certain the outlet

is properly grounded.

Note : Connect the machine to a power outlet which is not used for other

electric appliances. If a lighting fixture is connected to the same

outlet, the light may flicker.

Be sure to allow the required space around the machine for servicing

and proper ventilation.

20 cm

)

20 cm

)

20 cm (8

)

MX-M232D (GENERAL) 1 - 2

D. Note for handling PWB and electronic parts

When handling the PWB and the electronic parts, be sure to observe the

following precautions in order to prevent against damage by static

electricity.

1) When in transit or storing, put the parts in an anti-static bag or an anti-

static case and do not touch them with bare hands.

2) When and after removing the parts from an anti-static bag (case), use

an earth band as shown below:

• Put an earth band to your arm, and connect it to the machine.

3) When repairing or replacing an electronic part, perform the procedure

on an anti-static mat.

MX-M232D (CONFIGURATION) 2 - 1

[2] CONFIGURATION

1. System Configurations

AR-D36 AR-D37

AR-SP10

MX-M182MX-M232D MX-M182D

MX-M202D

AR-VR7

(MX-M182 is standard)

MX-NB12

AR-RP10

(MX-M182D/M202D/

M232D only)

MX-FX13

MX-EB14

MX-XB17

MX-TR10

MX-USX1

Sharpdesk 1 license kit

MX-PK10

PS3 EXPANSION KIT

MX-USX5

Sharpdesk 5 license kit

MX-US10

Sharpdesk 10 license kit

MX-US50

Sharpdesk 50 license kit

MX-USA0

Sharpdesk 100 license kit

MX-M232D (CONFIGURATION) 2 - 2

STD: Standard

: Option installation enable

: Option installation disable

*1 Standard for U.S.A

*2 Not available for U.S.A

*3 MX-NB12 or MX-XB17 is required.

*4 MX-NB12 is required.

Model

Option MX-M182 MX-M182D/202D/232D

AR-RP10 Reversing single pass feeder (RSPF)

XO *1

AR-SP10 Single pass feeder (SPF)

OO *2

AR-D36 250-sheet paper feed unit

O O

AR-D37 2x250-sheet paper feed unit

O O

AR-VR7 DOCUMENT COVER STD

O *2

MX-NB12 NETWORK EXPANSION KIT

O O

MX-FX13 FACSIMILE EXPANSION KIT

O *3 O *3

MX-XB17 FACSIMILE MOUNTING KIT

O O

MX-TR10 JOB SEPARATOR

O O

MX-EB14 EXPANSION MEMORY BOARD

O O

MX-PK10 PS3 EXPANSION KIT

O*4 O*4

MX-USX1 SHARPDESK 1 LICENSE KIT

O O

MX-USX5 SHARPDESK 5 LICENSE KIT

O O

MX-US10 SHARPDESK 10 LICENSE KIT

O O

MX-US50 SHARPDESK 50 LICENSE KIT

O O

MX-USA0 SHARPDESK 100 LICENSE KIT

O O

MX-M232D (MX-M232D/M202D/M182D/M182) 3 - 1

[3] MX-M232D/M202D/M182D/M182

1. Installing conditions

A.The machine installation

Do not install your the machine in areas that are:

•damp, humid, or very dusty

•exposed to direct sunlight

•poorly ventilated

•subject to extreme temperature or humidity changes, e.g., near an air

conditioner or heater.

•Be sure to allow the required space around the machine for servicing

and proper ventilation.

B.Power source

•Use an exclusive to dedicated power outlet. If the power plug of this

machine is inserted into a power outlet commonly used with other

illumination units, flickers of the lamp may be result. Use a power outlet

which is not used commonly with any illumination units.

•Avoid complex wiring.

C.Grounding wire connection.

•To avoid danger, the power outlet must be grounded. If no grounding

wire is connected and a leakage occurs, a fire or an electric shock may

be result.

2. Removal of protective material and fixing

screw

1) Remove all tapes and protective material.

•Remove all tapes, then open the document cover and remove the

protective material of sheet shape

2) Remove the fixing screw.

•Use a coin to remove the fixing screw.

•The fixing screw is required when transporting the machine. Keep it in

the tray. (Refer to the later description.)

3.Installing procedure

A.Developer cartridge installation

1) Open the bypass tray, and open the side cover.

2) Open the front cover.

•Hold the both sides and pull down to open.

3) Loosen the screw and remove the developer cartridge.

4) Remove the developer tank from the developer cartridge.

5) While rotating the MG roller in the arrow direction, supply the

developer into the developer tank evenly so as not to overflow.

* Shake the developer bag enough before opening it.

MG roller

MX-M232D (MX-M232D/M202D/M182D/M182) 3 - 2

6) Check that two hooks of the developer unit is hooked on the toner

cartridge guide, and secure the toner cartridge guide to the

developing unit.

* Check that the DV seal is free from the developer. If developer is

attached to the DV seal, clean it.

* After supplying developer, do not tilt or shake the developer

cartridge.

7) Attach the developer cartridge to the main unit, and secure it with

the screw.

Note: After inserting the DV unit into the machine, be sure to tighten the

blue screw to fix it to the machine.

B.Toner cartridge installation

1) Remove the new toner cartridge from the bag. Grasp the cartridge

on both sides and shake it horizontally four or five times.

2) Insert the toner cartridge along the guides until it locks in place while

pushing the lock release lever

•If there is any dirt or dust on the toner cartridge, remove it before

installing the cartridge..

C. Set the toner density reference control level

1) With the front cover open, turn ON the machine power and enter

SIM25-02.

Note: When the machine is not in the simulation mode, if the front

cover is closed and the machine power is turned ON, toner

may be supplied from the toner cartridge to the developer

cartridge.

Under this state, the toner density reference control level

adjustment cannot be made properly.

Therefore, if the front cover is closed and the machine power

is turned ON with the machine not in the simulation mode,

dispose developer and supply new developer and adjust the

toner density reference level.

2) Close the front cabinet.

3) Press [START] key, and execute SIM25-02.

Note: It takes about 3 minutes to execute SIM25-02 completely.

During execution of this simulation, the front cover must not be

opened and the machine power must not be turned OFF.

4. Removal and storage of fixing screw

1) Lift the knob and gently pull out the tray.

2) Hold the paper pressure plate and turn the fixing screw in the arrow

direction.

3) Store the fixing pin and the fixing screw in the tray.

•Store the fixing screw which was removed in the above procedure 2 and

the fixing screw which was removed in procedure 2 of 2.

•Removal of protective material and fixing screw in the storage place in

the tray.

hook

4 or 5 times

Screw

fixing

MX-M232D (AR-SP10/AR-RP10) 4 - 1

[4] AR-SP10/AR-RP10

1. Unpacking

For unpacking, refer to the figure below.

2. Installation

Turn the main switch of the machine to the “OFF” position and then

remove the power plug of the machine from the outlet.

1) Remove the document cover.

Lift the document cover from the machine and tilt it to the rear side to

remove it.

2) Remove the right cabinet.

Remove the screws and remove the right cabinet.

3) Remove the document glass and the right document glass holder.

Remove the screws, remove the document glass from the machine,

and then remove the right document glass holder.

4) Attach the SPF glass holder.

Fit the SPF glass holder to the document glass.

Attach the document glass to the machine and fix it with the screws.

1‘13/Nov

MX-M232D (AR-SP10/AR-RP10) 4 - 2

5) Attach the right cabinet.

Reattach the right cabinet to its original position and fix it with the

screws.

6) Cut out the cut-out portion.

Cut out the cut-out portion of the rear cabinet with nippers or the like.

At this time, be careful about the orientation of the nippers so that the

cut plane of the rear cabinet is flat.

7) Attach the automatic document feeder.

Insert the hinge portions of the document feeder into the mounting por-

tions of the machine by holding the feeder at an angle toward the rear

side.

8) Connect the relay connector.

Connect the harness of the automatic document feeder to the connec-

tor of the machine and tighten the screws on the connector.

9) Remove the filament tape.

Remove the filament tape located in the positions shown in the illustra-

tion.

10) If the optical unit shifts and recognizes the boundary between

the OC glass and SPF glass cover, perform SIM 53-8. 1

Andere Handbücher für MX-M182

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sharp Multifunktionsdrucker Handbücher

Sharp

Sharp MX-4140N Bedienungsanleitung

Sharp

Sharp AR-M257 - Digital Imager B/W Laser Bedienungsanleitung

Sharp

Sharp AL-2021 Leitfaden

Sharp

Sharp MX-B402SC Bedienungsanleitung

Sharp

Sharp AR-M256 Bedienungsanleitung

Sharp

Sharp MX-3050N Bedienungsanleitung

Sharp

Sharp AR-550 Bedienungsanleitung

Sharp

Sharp CR4 Cloud Series Bedienungsanleitung

Sharp

Sharp MX-M753 Bedienungsanleitung

Sharp

Sharp MX-M316NV Bedienungsanleitung

Sharp

Sharp AR-M257 - Digital Imager B/W Laser Bedienungsanleitung

Sharp

Sharp MX-M354U N Bedienungsanleitung

Sharp

Sharp AL1215 - B/W Laser - Copier Bedienungsanleitung

Sharp

Sharp MX-B381 Bedienungsanleitung

Sharp

Sharp MX-7090N Bedienungsanleitung

Sharp

Sharp MX-2630N Bedienungsanleitung

Sharp

Sharp MX-3610N Bedienungsanleitung

Sharp

Sharp AJ-5030 Bedienungsanleitung

Sharp

Sharp MX 5500N - Color Laser - Copier Gebrauchsanweisung

Sharp

Sharp MX-B201D Bedienungsanleitung

Sharp

Sharp MX 3070 Betriebsanleitung

Sharp

Sharp AR-FX9 - Fax Interface Card Bedienungsanleitung

Sharp

Sharp MX-B467F Bedienungsanleitung

Sharp

Sharp MX-M753U Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung