Sharp EL-2910R Bedienungsanleitung

ELECTRONIC PRINTING CALCULATOR

DRUCKENDER TISCHRECHNER

CALCULATRICE IMPRIMANTE ÉLECTRONIQUE

CALCULADORA IMPRESORA ELECTRÓNICA

CALCOLATRICE ELETTRONICA STAMPANTE

ELEKTRONISK SKRIVANDE OCH VISANDE RÄKNARE

ELEKTRONISCHE REKENMACHINE MET AFDRUK OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUAL DE MANEJO

MANUALE DI ISTRUZIONI

BRUKSANVISNING

GEBRUIKSAANWIJZING

ENGLISH ................................................... Page 1

CALCULATION EXAMPLES ..................... Page 63

DEUTSCH .................................................. Seite 10

RECHNUNGSBEISPIELE ......................... Seite 63

FRANÇAIS ................................................. Page 19

EXEMPLES DE CALCULS ........................ Page 63

ESPAÑOL .................................................. Página 28

EJEMPLOS DE CALCULOS ..................... Página 64

ITALIANO ................................................... Pagina 37

ESEMPI DI CALCOLO ............................... Pagina 64

SVENSKA .................................................. Sida 46

GRUNDLÄGGANDE RÄKNEEXEMPEL ... Sida 65

NEDERLANDS .......................................... Pagina 54

REKENVOORBEELDEN ........................... Pagina 65

EL-2910R

Notes for handling Lithium batteries:

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to the

manufacturer’s instructions.

Hinweise zur Handhabung von Lithium-Batterien:

VORSICHT

Bei Verwendung einer uneeigneten Ersatzbatterie

besteht Explosionsgefahr.

Nur durch den gleichen oder einen vom Hersteller

empfohlenen gleichwertigen Typ ersetzen.

Verbrauchte Batterien gemäß Herstelleranleitung

entsorgen.

Remarques sur la manipulation des piles au lithium:

ATTENTION

Danger d’explosion de la pile si elle n’est pas remplacée

correctement.

Remplacez-la uniquement par le même type de pile ou

un type équivalent recommandé par le fabricant.

Débarrassez-vous des piles usagers en respectant les

instructions du fabricant.

Notas para el manejo de las baterías de litio:

PRECAUCIÓN

Peligro de explosión si reemplaza incorrectamente la

batería.

Reemplácela por otra igual o de tipo equivalente

recomendada por el fabricante.

Deshágase de las baterías de acuerdo con las

instrucciones del fabricante.

Note concernenti le batterie al litio:

AVVERTENZA

Se la batteria non viene sostituita in modo corretto c’è

pericolo di esplosioni.

Sostituire la batteria con una dello stesso tipo o con una

equivalente raccomandata dalla fabbrica.

Smaltire le batterie usate seguendo le istruzioni della

fabbrica.

Observera om hantering av litiumbatterier:

OBSERVERA!

Felaktigt batteribyte medför risk för explosion.

Byt endast ut batteriet mot ett batteri av samma eller

motsvarande typ rekommenderat av tillverkaren.

Kassera ett förbrukat batteri enligt tillverkarens

anvisningar.

Opmerkingen betreffende de behandeling van

lithiumbatterijen:

LET OP

Ontploffingsgevaar indien de batterij verkeerd wordt

aangebracht.

Vervang uitsluitend door een batterij van hetzelfde of

een gelijkwaardig type, aanbevolen door de fabrikant.

Gooi gebruikte batterijen weg overeenkomstig de

instructies van de fabrikant.

CONTENTS

OPERATIONAL NOTES

ENGLISH

Page

• INSTALLING OF BATTERY FOR

MEMORY PROTECTION .................................. 2

• OPERATING CONTROLS ................................. 3

• PAPER ROLL REPLACEMENT ......................... 5

• INK ROLLER REPLACEMENT ......................... 5

• ERRORS ........................................................... 6

• REPLACEMENT OF BATTERY FOR

MEMORY PROTECTION .................................. 7

• SPECIFICATIONS ............................................. 8

• RESETTING THE UNIT ..................................... 9

• CALCULATION EXAMPLES............................ 63

• TAX RATE CALCULATIONS ........................... 73

To insure trouble-free operation of your SHARP

calculator, we recommend the following:

1. The calculator should be kept in areas free from

extreme temperature changes, moisture, and

dust.

2. A soft, dry cloth should be used to clean the

calculator. Do not use solvents or a wet cloth.

3. Since this product is not waterproof, do not use it

or store it where fluids, for example water, can

splash onto it. Raindrops, water spray, juice,

coffee, steam, perspiration, etc. will also cause

malfunction.

4. If service should be required, use only a SHARP

servicing dealer, a SHARP approved service

facility or SHARP repair service.

5. If the unit is operated from AC power only, without

installing the memory protection battery, the set

tax rates and memory contents (including GT

memory) will be cleared if the power plug is

removed from the outlet. This will also occur when

the memory protection battery is replaced.

INSTALLING OF BATTERY FOR MEMORY PROTECTION

Before using for the first time, remove the attached

lithium battery, and install it in the equipment

according to the following procedure.

If the power cord is unplugged by accident when

operating with AC power only, the set tax rate and

the contents of memory will be lost.

1) Turn the power switch “OFF” and unplug the

power supply plug from the outlet.

2) Remove the battery cover on the back of the unit.

(Fig. 1)

3) Wipe the battery well with a dry cloth and place

the plus “+” side upward. (Fig. 2)

4) Replace the battery cover by reversing the

removal procedure.

5) Press the RESET switch on the back of the unit

(See page 9).

After battery installation

•Connect the power supply plug to an outlet and

turn the power switch “ON”.

Check that “0.” is displayed. If “0.” is not displayed,

remove the battery, reinstall it, and check the

display again.

•On the battery replacement date label found on

the back of the unit, write down the month and

year when the battery is installed, as a reference

for the next battery replacement.

Fig. 1 Fig. 2

OPERATING CONTROLS

OFF PICP

ON POWER SWITCH; PRINT / ITEM

COUNT MODE SELECTOR:

“OFF”: Power OFF

“•”: Power ON. Set to the non-print

mode.

“P”: Power ON. Set to the print

mode.

“P•IC”: Power ON. Set to the print

mode.

Each time or is

pressed, in the case of

additional and subtraction, or

or is pressed, in the

case of memory calculations,

the associated item counter is

incremented by one. Select the

“P•IC” position to print the

counter values.

• The count is printed when

the calculated result is

obtained.

• Pressing of ,

clears the counter.

Note: The counter has a maximum

capacity of 3 digits (up to

+999). If the count exceeds the

maximum, the counter will

recount from zero.

F 6 3 2 1 0 A

DECIMAL / ADD MODE SELEC-

TOR:

“F”: Floating.

“6 3 2 1 0”: Fixed.

“A”: Add mode.

ROUNDING SELECTOR:

“”: An answer is rounded up.

“5/4”: An answer is rounded off.

“”: An answer is rounded down.

GT RATE SET

GRAND TOTAL / RATE SETTING

MODE SELECTOR:

“GT”: This selector will accumulate the

following: (“

”will be printed.)

•Addition and subtraction totals

obtained with .

“•”: Neutral, GT OFF.

“RATE SET”: Set the key to position

to enter (or change) the

tax rate.

TAX-INCLUDING KEY

PRE-TAX KEY

DISPLAY SYMBOLS:

M : Memory symbol

Appears when a number is in the memory.

– : Minus symbol

Appears when a number is negative.

←: Error symbol

Appears when an overflow or other error is

detected.

PAPER FEED KEY

LAST DIGIT CORRECTION KEY

GRAND TOTAL KEY

NON-ADD KEY

SUBTOTAL KEY

CLEAR / CLEAR ENTRY KEY

TOTAL KEY

EQUAL KEY

CHANGE SIGN KEY:

Changes the algebraic sign of a number (i.e.,

positive to negative or negative to positive).

MARKUP KEY:

Used to perform mark-ups and mark-down.

RECALL AND CLEAR MEMORY KEY

RECALL MEMORY KEY

PERCENT CHANGE KEY

Never insert paper roll if torn. Doing so will cause

paper to jam. Always cut leading edge with

scissors first.

1) Insert the leading edge of the paper roll into the

opening. (Fig. 1)

2) Turn the power on and feed the paper by pressing

. (Fig. 2)

3) Lift the attached metal paper holder up and insert

the paper roll to the paper holder. (Fig. 3)

Fig. 3

Fig. 1

Fig. 2

PAPER ROLL REPLACEMENT

INK ROLLER REPLACEMENT

DO NOT PULL PAPER BACKWARDS AS THIS

MAY CAUSE DAMAGE TO PRINTING

MECHANISM.

If printing is blurry even when the ink roller is in the

proper position, replace the roller.

Ink roller: Type EA-781R-BK (Black)

Type EA-781R-RD (Red)

WARNING

APPLYING INK TO WORN INK ROLLER OR

USE OF UNAPPROVED INK ROLLER MAY

CAUSE SERIOUS DAMAGE TO PRINTER.

1) Set the power switch to OFF.

2) Remove the printer cover. (Fig. 1)

3) Remove the ink roller by turning it counterclockwise

and pulling it upward. (Fig. 2)

4) Install the correct color new ink roller and press it

in the correct position. Make sure that the ink roller

is securely in place. (Fig. 3)

5) Put back the printer cover.

Fig. 1 Fig. 2

Fig. 3

ERRORS

Red Black

Cleaning the printing mechanism

If the print becomes dull after long time usage,

clean the printing wheel according to the

following procedures:

1) Remove the printer cover and the ink roller.

2) Install the paper roll and feed it until it comes out

of the front of the printing mechanism.

3) Put a small brush (like a tooth brush) lightly to the

printing wheel and clean it by pressing .

4) Put back the ink roller and the printer cover.

Notes: •Do not rotate the printing mechanism

manually, this may damage the printer.

•Never attempt to turn the printing belt or

restrict its movement while printing. This

may cause incorrect printing.

There are several situations which will cause an

overflow or an error condition. When this occurs, “←”

will be displayed. The contents of the memory at the

time of the error are retained.

If “←”is displayed at the time of the error,

“•••••••••••••••••” will be printed in black and must

be used to clear the calculator.

Error conditions:

1. When the integer portion of an answer exceeds

12 digits.

2. When the integer portion of the contents of the

memory exceeds 12 digits.

(Ex. 999999999999 1 )

3. When any number is divided by zero. (Ex. 5 0

4. This unit is equipped with a key input buffer (12

row max.), and it may give an error message if

you exceed the buffer limit by pressing keys

sequentiallly during printing.

Time for battery replacement

Replace with a new battery once 2 year.

Method of battery replacement

Use one lithium battery (CR2032).

Note: When replacing the battery, the set tax rate

and the memory contents will be lost.

You may want to write down the tax rate and

other important numbers on a sheet of paper.

1) Turn the power switch “OFF”and unplug the

power supply plug from the outlet.

2) Remove the battery cover on the back of the unit.

(Fig. 1)

3) Remove the exhausted battery and install one

new lithium battery. Wipe the battery well with a

dry cloth and place the plus “+”side upward. (Fig.

4) Replace the battery cover by reversing the

removal procedure.

5) Press the RESET switch on the back of the unit

(See page 9).

After battery replacement

•Connect the power supply plug to an outlet and

turn the power switch “ON”.

Check that “0.”is displayed. If “0.”is not displayed,

remove the battery, reinstall it, and check the

display again.

•Reset the tax rate.

•On the battery replacement date label found on

the back of the unit, write down the month and

year when the battery is replaced, as a reference

for the next battery replacement.

REPLACEMENT OF BATTERY FOR MEMORY PROTECTION

Fig. 1 Fig. 2

Precautions on battery use

•Do not leave an exhausted battery in the

equipment.

•Do not expose the battery to water or flame, and

do not take it apart.

•Store batteries out of the reach of small children.

Operating capacity: 12 digits

Power supply: Operating:

AC: 220V-230V, 50Hz

Memory backup:

3V ... (DC)

(Lithium battery CR2032 ×

Memory Protection Battery lifespan:

Approx. 2 years. (tested

and confirmed at 25°C

(77°F); may change due to

usage environment)

PRINTING SECTION

Printer: Mechanical printer

Printing speed: Approx. 3.0 lines/sec.

Printing paper: 57 mm (2-1/4”) –58 mm (2-

9/32”) wide

80 mm (3-5/32”) in

diameter (max.)

Operating temperature: 0°C –40°C (32°F –104°F)

Power consumption: 74 mA

Dimensions: 221 mm (W) ×305 mm (D)

×72 mm (H)

(8-11/16”(W) ×12-1/16”

(D) ×2-27/32”(H))

Weight: Approx. 1.3 kg (2.87 lb.)

(with battery)

Accessories: 1 lithium battery, 1 battery

replacement date label

(attached on the unit’s

back body), 1 paper roll, 2

ink rollers (installed), and

operation manual

SPECIFICATIONS

Andere Handbücher für EL-2910R

Inhaltsverzeichnis

Andere Sharp Kalkulator Handbücher

Sharp

Sharp EL-R277B-BK Bedienungsanleitung

Sharp

Sharp QS-1760H Bedienungsanleitung

Sharp

Sharp ELSI MATE EL-327S Bedienungsanleitung

Sharp

Sharp ELSI MATE EL-250S Bedienungsanleitung

Sharp

Sharp EL-500M Bedienungsanleitung

Sharp

Sharp ELSIMATE EL-344R Bedienungsanleitung

Sharp

Sharp EL-501V Bedienungsanleitung

Sharp

Sharp ELSI MATE EL-326S Bedienungsanleitung

Sharp

Sharp EL-8130 Bedienungsanleitung

Sharp

Sharp EL-W516B - Scientific Calculator With... Bedienungsanleitung

Sharp

Sharp Scientific calculator Bedienungsanleitung

Sharp

Sharp ELSI MATE EL-250S Bedienungsanleitung

Sharp

Sharp CS-4194H Bedienungsanleitung

Sharp

Sharp EL-546VA Bedienungsanleitung

Sharp

Sharp Elsi Mate EL-792C Bedienungsanleitung

Sharp

Sharp PC-1245 Bedienungsanleitung

Sharp

Sharp EL-344R Bedienungsanleitung

Sharp

Sharp EL-733A Bedienungsanleitung

Sharp

Sharp EL-2607R Bedienungsanleitung

Sharp

Sharp ELSIMATE EL-480SRB Bedienungsanleitung

Sharp

Sharp EL-5060 Bedienungsanleitung

Sharp

Sharp EL-W516T Bedienungsanleitung

Sharp

Sharp EL-337M Bedienungsanleitung

Sharp

Sharp EL-376SB Bedienungsanleitung

Beliebte Kalkulator Handbücher anderer Marken

HP 35s Handbuch

Casio

Casio CFX-9970G Bedienungsanleitung

LEXIBOOK

LEXIBOOK EL350 Bedienungsanleitung

HP HP-97 Bedienungsanleitung

Citizen

Citizen SDC-414N Bedienungsanleitung

Casio

Casio fx-3800P Bedienungsanleitung

Canon

Canon P26-DHIII Bedienungsanleitung

Citizen

Citizen 520DPA Bedienungsanleitung

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 Bedienungsanleitung

Casio

Casio MS-7UC Bedienungsanleitung

Casio

Casio FC-200 Bedienungsanleitung

Casio

Casio fx-CG50 Bedienungsanleitung

HP HP-67 Benutzerhandbuch

Royal

Royal CBC2000 Bedienungsanleitung

Heathkit

Heathkit IC-2009 Bedienungsanleitung

Universal

Universal UNV-15907 Bedienungsanleitung

Casio

Casio ALGEBRA FX 2.0 Bedienungsanleitung

Casio

Casio CLASSPad300 - ClassPad 300 Touch-Screen Graphing Scientific... Bedienungsanleitung