Sharp XE-A201 Stücklistenhandbuch

XEA201 Frequently Asked Questions Page 1 of 17

XEA201 Frequently Asked Questions.

XEA201 Frequently Asked Questions Page 2 of 17

How do I prepare my XEA201 for set-up?

Take the XEA201 out of its box, remove the packing materials. Place the XEA201 on a flat stable surface,

close to a power outlet. Also insure it will not be exposed to direct sunlight, and is away from water (taps,

sinks, etc).

How do I clear the XEA201 to ready it for programming?

It is very important that you “initialise” the XEA201 correctly once you have removed it from the box, and

are ready to start programming. If you do not “initialise” the XEA201, it might not work correctly.

1. Insert the Mode key into the mode switch and turn it to the REG position.

2. Plug the AC adapter connector into the AC adapter jack, then plug the AC adapter into the wall

outlet.

This must be done without the batteries installed. If you have installed batteries; be sure to remove

them before you start this procedure.

After a few seconds, the register should beep three times, and the display should look as indicated

below.

The register is initialised.

If the beeps are not heard as described, the initialisation has not been successful. If this is the case:

disconnect the register from the AC outlet, wait at least one minute, and then try again.

If there were any data from a previous programming attempt, they would have been cleared

XEA201 Frequently Asked Questions Page 3 of 17

How to install the batteries, and why should I do so?

The XEA201 uses 3 x AA size batteries to hold its preset, and sales data in memory when it is switched

off. If you do not install 3 x AA size batteries; the XEA201 will be cleared of all preset, and sales data

when it is turned off.

1. Lift the printer cover up and forward, and detach it. Be careful of the paper cutter to avoid cutting

yourself.

2. Open the battery compartment cover next to the paper roll cradle.

3. Install 3 alkaline AA size batteries.

4. When the batteries are properly installed the “ ” message on the display will disappear.

Note: If you press a key by mistake, an error symbol “PPPPPPPPPP” might be displayed. Press CL

to clear the symbol after installing the paper rolls. (see next question).

5. Close the battery compartment cover.

A set of new alkaline batteries once installed will keep the memory for up to one year without power.

Please see the question on how to replace the batteries for details on when and how to replace the batteries.

If the unit is not used for some months, you might not get any warning when you turn it on that the

batteries have failed. In this instance, the XEA201 will initialise itself.

XEA201 Frequently Asked Questions Page 4 of 17

What sort of paper roll do I use, and how do I install it?

The XEA201 uses a thermally sensitised paper roll which is: 57mm wide. Its maximum diameter should

be no more than 80mm.

1. Pull the printer cover forward and detach it. The paper cutter is mounted on the printer cover, be

careful not to cut yourself.

2. Make sure the print head release lever is positioned as per the diagram below.

3. Before placing a new paper roll in the paper roll cradle, cut off the pasted (taped), part of the paper

and confirm that the cut end of the paper is straight.

4. Set the paper roll into the paper roll cradle as per the diagram below.

XEA201 Frequently Asked Questions Page 5 of 17

5. Insert the end of the paper into the printer until it is caught by the printer auto-feeds and comes out

of the top of the printer. If the printer does not catch the paper, feed the paper while pressing the 

key.

6. Cut off the excess paper and replace the printer cover.

7. Press the key to make sure the paper end comes out of the printer cover and clean paper appears.

If the paper end does not come out. Open the printer cover, and pass the paper end between the

paper cutter and the paper guide of the printer cover, and replace the cover.

XEA201 Frequently Asked Questions Page 6 of 17

How do I set the time and date?

1. Set the mode key to the PGM position.

2. Enter the time as a four digit number. Use the 24 hour format. For example

2:30pm would be entered as 1 4 3 0

3. Press the #/TM/ST key

4. Enter the date as an eight digits using the day-month-year format. For example

5. 7th of December 2012 would be entered as 0 7 1 2 2 0 1 2

6. Press the #/TM/ST key

How do I set a 10% GST rate?

1. Set the mode key to the PGM position

2. Enter:

#/TM/ST 9 1 1 0 0 0 0 0 #/TM/ST TL/NS

XEA201 Frequently Asked Questions Page 7 of 17

How do I set a Department as taxable or not taxable?

1. Set the mode key to the PGM position

2. To make a department taxable, enter:

-1--0-0 -8--1-DEPT KEY TL/NS

For example to make department 1 taxable enter:

-1--0-0 -8--1-1 17 TL/NS

For example to make department 1 non-taxable enter:

-8--1-1 17 TL/NS

Press _SHIFT then the department key for departments 17 to 32

For example to make department 17 taxable enter:

-1--0-0 -8--1-SHIFT 1 17 TL/NS

For example to make department 17 non-taxable enter:

-8--1-SHIFT 1 17 TL/NS

XEA201 Frequently Asked Questions Page 8 of 17

How do I set the letters GST to print on the receipt?

1. Set the mode key to the PGM position

2. Enter: #/TM/ST -3-_●_9 

-G--S--T-#/TM/ST TL/AT/NS

You can enter characters with the department and function keys. You will see the

letters of the Alphabet that a key covers in the bottom right hand corner of the key.

You can also enter text using 3 digit codes. Please refer to the full instruction manual (pages 33 -34)

for details.

How do I set the $ symbol to print on receipts?

1. Set the mode key to the PGM position

XEA201 Frequently Asked Questions Page 9 of 17

2. Enter:

#/TM/ST 8 5 _●0 3 2 _00_0 3 2 _00_0 3 2 _00_

0 3 6 _00_#/TM/ST TL/NS

How do I make cash sales amounts round to the nearest 5 cents?

3. Set the mode key to the PGM position

4. Enter:

#/TM/ST 6 7 _1 1 8 _2_1 0 1 0 #/TM/ST TL/NS

How do I change the power save (screen off) time?

5. Set the mode key to the PGM position

6. Enter:

#/TM/ST 1 0 _9 9 9 #/TM/ST TL/AT/NS

This will set the power save function off.

XEA201 Frequently Asked Questions Page 10 of 17

How do I stop the Electronic Journal near full error symbol from dispalying?

7. Set the mode key to the PGM position

8. Enter:

#/TM/ST 6 8 _0 0 1 _0_0 0 1 0 #/TM/ST TL/AT/NS

This will cause the near full symbol for the Electronic Journal (EJ), not to display. The EJ near full

warning symbol is a ●displayed right below the 8th and 9th places on the display. If this warning is

disabled records in the EJ will be deleted on a first in first out (FIFO) basis. The EJ has a 2000 line

capacity.

How do I give a department a descriptive name?

1. Set the mode key to the PGM position

2. Enter: #/TM/ST -1-_●_DEPT KEY enter characters

#/TM/ST TL/NS

You can enter up to 12 characters with the function and department keys. You will see the

letters of the Alphabet that a key covers in the bottom right hand corner of the key.

You can also enter text using 3 digit codes. Please refer to the full instruction manual (pages 33 -34)

for details.

Andere Handbücher für XE-A201

Andere Sharp Kasse Handbücher

Sharp

Sharp XE-A212 Bedienungsanleitung

Sharp

Sharp XE-A407 Bedienungsanleitung

Sharp

Sharp XE-A130 Kurzanleitung

Sharp

Sharp UP-700 Produkthandbuch

Sharp

Sharp ER-A750 Bedienungsanleitung

Sharp

Sharp ER-A520 Produkthandbuch

Sharp

Sharp XE-A203 - Cash Register Thermal Printing Graphic Logo... Bedienungsanleitung

Sharp

Sharp XE-A110 Bedienungsanleitung

Sharp

Sharp ER-A440 Bedienungsanleitung

Sharp

Sharp ER-A310 Bedienungsanleitung

Sharp

Sharp XE-A106 Bedienungsanleitung

Sharp

Sharp ER-A410 Bedienungsanleitung

Sharp

Sharp UP-700 Service-Handbuch

Sharp

Sharp XE-A202 - Electronic Cash Register Bedienungsanleitung

Sharp

Sharp ER-2590 Bedienungsanleitung

Sharp

Sharp XE-A307 Bedienungsanleitung

Sharp

Sharp XE-A101 Bedienungsanleitung

Sharp

Sharp ER-A610 Betriebsanleitung

Sharp

Sharp ER-A460 Bedienungsanleitung

Sharp

Sharp XE-A301 Bedienungsanleitung

Sharp

Sharp UP-600 Bedienungsanleitung

Sharp

Sharp XE-A106 Bedienungsanleitung

Sharp

Sharp XE-A107 Kurzanleitung

Sharp

Sharp XE-A303 Bedienungsanleitung

Beliebte Kasse Handbücher anderer Marken

Royal

Royal 480nt Bedienungsanleitung

Olivetti

Olivetti ECR 8200 S Bedienungsanleitung

TEC

TEC TEC FS-3600 Bedienungsanleitung

Integrated System Laboratory

Integrated System Laboratory ISL 4006 Bedienungsanleitung

Sam4s

Sam4s ER-380 Fehlerbehebungshandbuch

Samsung

Samsung ER 5215 Bedienungsanleitung

Toast

Toast Toast Bedienungsanleitung

TEC

TEC MA-600-1 series Bedienungsanleitung

QUORION

QUORION CR 1200 Bedienungsanleitung

Olivetti

Olivetti ECR 7700 LD eco Plus Bedienungsanleitung

TEC

TEC TEC MA-1060 Bedienungsanleitung

Casio

Casio PCR-408 Montageanleitung

ELCOM

ELCOM Euro-2100TE Bedienungsanleitung

American Changer

American Changer CLASSIC Series Bedienungsanleitung

Sam4s

Sam4s ER-180 Bedienungsanleitung

Sam4s

Sam4s ER-5100? SERIES Bedienungsanleitung

Casio

Casio PCR-T273 Bedienungsanleitung

Casio

Casio PCR-T2100 Bedienungsanleitung