Sharp TM150 Bedienungsanleitung

CODE : 00ZTM150/SM/E

qSERVICE MANUAL

CONTENTS

Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specified

ones for maintaining the safety and performance of the set.

SHARP CORPORATION This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

CONFIDENTIAL DRAFT

DIGITAL MOBILE PHONE

MODEL TM150

(INTERNAL MODEL NAME: TM150U)

• In the interests of user-safety the set should be restored

to its original condition and only parts identical to those

specified should be used.

Caution:

Risk of explosion if battery is replaced by an incorrect type,

dispose of used batteries according to the instruction.

SERVICING CONCERNS

CHAPTER 1.GENERAL DESCRIPTION

[1] Specifications . . . . . . . . . . . . . . . . . . . . . . . .1-1

[2] Names of parts. . . . . . . . . . . . . . . . . . . . . . .1-2

[3] Operation manual. . . . . . . . . . . . . . . . . . . . .1-3

CHAPTER 2.

ADJUSTMENTS, PERFORMANCE

CHECK, AND FIRMWARE UPGRADE

[1] SHARP Program Support Tool (SPST) . . . . 2-1

[2] Test points . . . . . . . . . . . . . . . . . . . . . . . . .2-48

[3] Trouble shooting. . . . . . . . . . . . . . . . . . . . .2-52

CHAPTER 3. DISASSEMBLY AND REASSEMBLY

[1] Servicing Concerns . . . . . . . . . . . . . . . . . .3-1

[2] Disassembly and reassembly. . . . . . . . . . .3-4

CHAPTER 4. DIAGRAMS

[1] Block diagram . . . . . . . . . . . . . . . . . . . . . . . 4-1

CHAPTER 5. CIRCUIT DIAGRAM

[1] Notes on schematic diagram. . . . . . . . . . . . 5-1

[2] Types of transistor and LED . . . . . . . . . . . . 5-1

[3] Waveforms of circuit . . . . . . . . . . . . . . . . . . 5-2

[4] Schematic diagram/

Wiring side of P.W.Board. . . . . . . . . . . . . . . . . 5-5

CHAPTER 6. OTHERS

[1] Function table of IC. . . . . . . . . . . . . . . . . . . 6-1

Parts Guide

TM100 SERVICING CONCERNS

CONFIDENTIAL DRAFT

SERVICING CONCERNS

1. When requested, back up user’s handset data using SPST (SHARP Program Support Tool). Otherwise, before servicing, warn the user that data

in the memory may be lost during repairs.

2. Upgrade the firmware to the latest version using SPST before returning the handset to the customer.

3. After repairs, inspect the handset according to the following flowchart.

4. When storing or transporting a PWB, put it into a conductive bag or wrap it in aluminum foil.

(C-MOS IC may be damaged by electrostatic charges.)

5. Do not leave fingerprints, etc. on ornamental parts including a cabinet, especially clear windows for main and sub displays.

Wear fingerstalls to avoid this.

Also, ensure not to leave fingerprints on the surface of main and external display panels.

6. To prevent oxidation which causes connection problems, do not touch any terminals on the electric board,

microphone, vibrator, earpiece and speaker.

When handling these parts, wear fingerstalls. Should you touch these parts, clean them with a soft dry cloth.

Always wear fingerstalls when handling a shield case on the electric board.

Otherwise oxidation may occur causing handset performance deterioration.

7. The FPC is a precision device. Handle it carefully to prevent any damages.

8. Do not expose the moisture sensor to liquids.

If the sheet gets wet, red ink runs. In this case, replace the sheet with a new one.

Be careful about your perspiration.

9. Before you disassemble or reassemble handset, make sure to remove the Li-Ion battery.

10. Be sufficiently careful with static electricity of integrated circuits and other circuits. Wear static electricity prevention bands while servicing.

Repairs are completed.

(Fixed parts have been checked for proper operation.)

Check IMEI No./Operator code (Destination)/

Firmware version by Identity function of SPST.

Inspect each device using performance check adjustment function of SPST.

Carry out RF performance check with SPST.

All completed.

TM150 GENERAL DESCRIPTION

1 – 1

CONFIDENTIAL DRAFT

CHAPTER 1. GENERAL DESCRIPTION

1. SPECIFICATIONS

Battery running time depends on the battery and SIM card as well as the network conditions and usage.

FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL.

General: Quad - band (GSM 900 MHz/DCS 1800 MHz/PCS 1900MHz)

GPRS-enabled WAP, MMS, SMS

Dimensions

(folded, excluding

the aerial) (H x W x D): 27.1 x 49.2 x 94.8 mm

Weight: 112 g

Battery operating temperature: 0 °C - 40 °C

Main display: Display dimensions: 240 x 320 pixels

LCD display: CGS 262,144 colours with backlight

LCD backlight: LED backlight white colour LEDs

External display: Display dimensions: 64 x 96 pixels

LCD display: STN 65,536 colours LCD with backlight

Camera: CCD 1M pixels built-in camera Zoom: Wide and zoom mode

[Supported 20 (when image size is 120 x 160 pixels) x zoom]

Lens: F2.8, f = 3.7 mm

Sound: 16-polyphonic ring melodies

External DC supply voltage: 5.2 V

Battery: 3.7 V, 780 mAh, Li-Ion

Standby time: 100 ~ 250 hours

Talk time: 160 ~ 240 min.

Others: Side key Connector for AC charger and data cable Standard hands free connector ($2.5)

Specifications for this model are subject to change without prior notice.

Java and all Java-based trademarks and logos are

trademarks or registered trademarks of Sun Micro-

systems, Inc. in the U.S. and other countries.

JBlend and all JBlend-based trademarks and logos

are trademarks or registered trademarks of Aplix

Corporation in Japan and other countries.

/Micro3D EditionTM

Mascot CapsuleR

is a registered trademark of HI Corporation

Licensed by Inter Digital Technology Corporation under one or more

of the following United States Patents and/or their domestic or foreign

counterparts and other patents pending, including U.S. Patents:

4,675,863 : 4,779,262 : 4,785,450 & 4,811,420.

Licensed under U.S. Patent 4,558,302 and foreign counterparts.

T9 Text Input is licensed under one or more of the following: U.S. Pat.

Nos. 5,818,437, 5,953,541, 5,187,480, 5,945,928, and 6,011,554;

Australian Pat. No. 727539; Canadian Pat. No. 1,331,057;United

Kingdom Pat. No. 2238414B; Hong Kong Standard Pat. No.

HK0940329; Republic of Singapore Pat. No. 51383; Euro. Pat. No. 0

842 463 (96927260.8) DE/DK, FI, FR, IT, NL,PT.ES,SE,GB; Republic

of Korea Pat. Nos. KR201211B1 and KR226206B1; and additional

patents are pending worldwide.

SD logo is a trademark.

CP8 PATENT

TM150 GENERAL DESCRIPTION

1 – 2

CONFIDENTIAL DRAFT

2. NAMES OF PARTS

No. PARTS NAME

1 SPEAKER

2SUBLCD

3STRAP

4 CAMERA

5 CLOSE-UP KNOB

6 PHONE JACK

7 SD CARD SLOT

8 BATTERY LOCK KNOB

9 EXT ANTENNA

10 SIDE KEY

11 I/O CONNECTER

12 RECEIVER

13 MIC

TM150 GENERAL DESCRIPTION

1 – 3

CONFIDENTIAL DRAFT

3. OPERATION MANUAL

(Page numbers refer to the user guide)

[OPTIONAL ACCESSORIES]

• USB data cable

The above accessories may not be available in all regions. For details, please contact your dealer.

[QUICKSTART GUIDE]

TM150 GENERAL DESCRIPTION

1 – 4

CONFIDENTIAL DRAFT

New Messages

Download Games

News Spor t

1-3

6-3-3

7-5

TM150 ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE

2 – 1

CONFIDENTIAL DRAFT

CHAPTER 2. ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE

SPST (SHARP Program Support Tool) allows you to adjust settings, conduct performance checks, and upgrade the firmware.

[1] SHARP PROGRAM SUPPORT TOOL (SPST)

1. SYSTEM REQUIREMENTS

• IBM PC compatible personal computer (standard COM1 115,200 bps

serial port and USB required)

Supported OS: Windows 98/98SE/2000/XP

(except for Windows 95/ME/NT)

(English, German, Italian, Spanish, French and Chinese versions)

• Data cable

• GSM tester: CMU200

• GPIB interface: National Instruments USB-GPIB cable

(Model No.: NI GPIB-USB-B)

2. INTRODUCTION

2-1. FUNCTIONS

SPST offers seven key functions:

1) Firmware download

2) User data transfer (processes all data at once but not individually.)

3) RF calibration check and test

4) Default setting

5) Identification

6) Performance check and adjustment

7) User password reset

2-2. INSTALLATION

1. Use Windows Explorer to execute the "setup.exe" file on the CD-

ROM.

2. The SPST TM150 setup wizard appears. Follow the installation

instructions.

3. After the installation is complete, shortcuts to SPST are created on

the desktop and under the "Start"-"Programs"-"TM150" menu.

Start SPST from the shortcuts.

2-3. STARTING UP

Connect TM150 to an operable serial port of the PC with the supplied

data cable. Make sure that the battery is fully charged.

Start SPST from the desktop.

1. The Input password dialog box appears. Enter the password, select

a port where TM150 is connected from the list box, and click "OK".

If you do not know SPC, click “Cancel” to exit.

2. To change the password, enter the current password in procedure 1,

and then click "Change Password".

To check the usage status oftools, click "Show Repair Log" in procedure 1.

4. Click “Downloader for Emergency”.

The above screen appears. Select a model to use and execute the

Downloader. (Use this to initialize the flash, etc.)

5. When the password is correct, a connection is established and the

following screen appears.

Refer to the attachment 1

for the destination and

operator name.

TM150

Software version:

A02-006-0138-TM150

TM150 ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE

2 – 2

CONFIDENTIAL DRAFT

■Buttons

3. ADJUSTMENTS FOR TM150

1. Adjustments are required after replacing the following parts. ( F)

When replacing other parts in the RF section, carry out RF calibration.

2. Click the buttons on the SPST screen for adjustments. 3. The following screen appears.

Default Set Refer to "4-1. Default setting".

User Data Back-up Refer to "4-2. User data back-up".

User Data Restore Refer to "4-3. User data restore".

Downloader Refer to "4-4. Downloader".

RF Calibration & Check Refer to "4-5. RF calibration & check".

RF Test Refer to "4-6. RF test tool".

User Password Reset Refer to "4-7. Password reset".

Performance check

adjustment

Refer to "4-8. Performance check and adjustment".

**** mode release Refer to "4-9. ****mode release".

Exit End SPST.

Parts Temperature adjustment

(Camera) Temperature adjustment

(Battery) Main display

flicker adjustment White defect correction

TH101 uFuu

TH701 Fuuu

Main display unit uuFu

Camera unit uuuF

To abjust the device, click this button

(Performance check adjustment).

RF calibration

1Temperature adjustment (Camera section)

2Temperature adjustment (Battery section)

3Main display flicker adjustment

4External display contrast adjustment

5White defect correction

6Black defect correction

TM150 ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE

2 – 3

CONFIDENTIAL DRAFT

4. FUNCTIONS

4-1. DEFAULT SETTING

SPST can restore the factory settings.

This function

1. Deletes all user data in the file system;

2. Restores all WAP settings to default; and

3. Restores the values set by the user to default;

(MEP_LOCK settings and the destination and operator name do not change.)

1) Set the COM port on the SPST initial screen and click "Default Set".

2) Click "Yes" to proceed. Click "No" to exit.

3) Click "Yes" to back-up the MEPLOCK data. Click "No" to restore

default settings.

4) Communication starts.

5) The following appears when you select "Yes" in step 3 and

MEPLOCK data exists. Click "Yes" to restore the data.

6) After the handset is turned on, the initialization is complete.

4-2. USER DATA BACK-UP

SPST saves all the data stored on the handset.

1. Set the COM port on the SPST initial screen and click

"User Data Back-up".

2. Specify the file name in the following dialog box and click "Save"

3. The communicating dialog box appears while processing.

4. When completed, the following message appears. Click "OK".

4-3. USER DATA RESTORE

SPST completely restores the backed up data.

1. Set the COM port on the SPST initial screen and click "User Data

Restore".

2. Specify the file name in the following dialog box and click "Save".

TM150

TM150 ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE

2 – 4

CONFIDENTIAL DRAFT

3. The communicating dialog box appears while processing.

4. When the restore is complete, click "OK".

4-4. DOWNLOADER

4-4-1. Introduction

Downloader allows you to upgrade the firmware.

1) System requirements

• Requirements for the upgrading tool:

• Requirements for Loading loader

2) Required devices

The following devices are required to rewrite MOT files using Communi-

cation Box.

Conversion connector (16-pin 310-pin)

This conversion connector is required to connect TM150 with Communica-

tion Box since the cable connector of Communication Box has 16 pins.

4-4-2. Getting started

This section describes how to install/uninstall the software and how to

connect handset to a PC.

1) Installing/uninstalling the software

[Connecting handset to a PC]

1. Double click the “setup.exe” icon in TM150 Install-E folder.

2. The Setup Wizard is activated.

Click the "Next" button.

3. A location to install the software appears.

To install in the default location, click the "Next" button.

To change the location, click the "Browse" button, select a desired

location and then click the "Next" button.

(See the description in "* Changing the install location" below.)

OS : Windows 98, 98 SE, 2000, or XP

Download file : Only the Motorola format is supported.

Communication method : Asynchronous mode

Data length : 8 bits

Parity bit : None

Stop bit length : 1 bit

Handset : TM150

Communication method : Asynchronous mode

Data length : 8 bits

Parity bit : None

Stop bit length : 1 bit

TM150

Andere Handbücher für TM150

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sharp Handy Handbücher

Sharp

Sharp 703SH Bedienungsanleitung

Sharp

Sharp AQUOS sense3 Bedienungsanleitung

Sharp

Sharp 902SH Bedienungsanleitung

Sharp

Sharp disney DM008SH Bedienungsanleitung

Sharp

Sharp Aquos SH-02K Bedienungsanleitung

Sharp

Sharp 903SH Bedienungsanleitung

Sharp

Sharp SHV44 Kurzanleitung

Sharp

Sharp TM200 Bedienungsanleitung

Sharp

Sharp Aquos D10 Bedienungsanleitung

Sharp

Sharp SX862 Bedienungsanleitung

Sharp

Sharp Aquos Sense3 SHV45 Bedienungsanleitung

Sharp

Sharp GX33 Bedienungsanleitung

Sharp

Sharp Docomo AQUOS Ever SH-02J Bedienungsanleitung

Sharp

Sharp Aquos phone SL Service-Handbuch

Sharp

Sharp GX25C Bedienungsanleitung

Sharp

Sharp Disney Mobile DM003SH Bedienungsanleitung

Sharp

Sharp AQUOS K SHF34 Bedienungsanleitung

Sharp

Sharp GX10 Bedienungsanleitung

Sharp

Sharp Aquos Phone Serie SHL22 Service-Handbuch

Sharp

Sharp SHV40 Installationsanleitung

Sharp

Sharp AQUOS Crystal Bedienungsanleitung

Sharp

Sharp Aquos SHL23 Installationsanleitung

Sharp

Sharp Aquos SHL22 Technisches Datenblatt

Sharp

Sharp Aquos R compact Installationsanleitung

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LG LM-X420QN Bedienungsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

LG LM-K420EMW Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung