Sharp RD-1230 Bedienungsanleitung
RADIAL DRILLS
RD-1230 RD-1600 RD-2000
OPERATION MANUAL
0-1
Section Content page
CHAPTER 1 Safety Guidelines
1.1 Please follow the below basic safety principles ……………………….. 1-1
1.2 Precautions for the transportation and installation …………………….. 1-1
1.3 Precautions for operation …………………………………………….. 1-1
1.4 Precautions for checking and maintenance …………………………….. 1-2
1.5 Warning labels on the machine …………………………………………. 1-3
1.5.1 Warning labels and mark introduction……………………………………….. 1-3
1.5.2 Labels ………………………………………………………………………. 1-4
CHAPTER 2 General specifications
2.1 The anticipated machine life ……………………………………………. 2-1
2.2 Machine dimensions ……………………………………………………. 2-1
2.3 The machine …………………………………………………………………. 2-2
2.3.1 Description …………………………………………………………………. 2-2
2.3.2 Parts …………………………………………………………………………. 2-2
2.4 Specifications ………………………………………………………………... 2-3
2.4.1 TPR-1230H Specification ……………………………………………….. 2-3
2.4.2 TPR-1230 Specification ……………………………………………….. 2-4
2.4.3 TPR-1600H Specification ……………………………………………….. 2-5
2.4.4 TPR-2000H Specification …………………………………………. 2-6
2.5 Standard and Option Accessories …………………………………………. 2-7
2.6 Operation position and noise level …. ……………………………………... 2-7
2.6.1 Operation position …………………………………………………….. 2-7
2.6.2 The noise level ……………………………………………………………. 2-7
CHAPTER 3 Preparation to install
3.1 Space and room requirement …………………………………………….. 3-1
3.1.1 Floor requirement ………………………………………………………… 3-1
3.1.2 Space requirement ………………………………………………………… 3-3
3.2 Environment requirement ……………………………………………… 3-3
3.3 Power supply requirement ……………………………………………… 3-4
3.4 Electric system alculation ……………………………………………… 3-5
CHAPTER 4 Transportation and Installation
4.1 Disassembly and packaging ……………………………………………. 4-1
4.1.1 General ……………………………………………………………….…… 4-1
4.1.2 Packaging …………………………………………………………………. 4-1
4.2 Transportation ……………………………………………………………... 4-2
4.2.1 The diagram of the machine weight and its gravity center ……………. 4-2
0-2
Section Content page
4.2.2 The movement of the machine ………………………………………… 4-2
4.2.3 The order to pack …………………………………………………………... 4-3
4.3 Installation of the machine ……………………………………………… 4-3
4.3.1 Have the machine set onto the fastening bolts of the crate base ………. 4-3
4.3.2 Level adjusting. ……………………………………………………………. 4-4
4.3.3 The installation of the electricity ……………………………………… 4-4
4.4 The test after installation ……………………………………… 4-4
4.5 The procedure for dismantling the machine ………………………….. 4-4
CHAPTER 5 Operation
5.1 A brief introduction to the relevant operation hardware ………………. 5-1
5.1.1 (For TPR-1230, TPR-1230H) ……………………………………….. 5-1
5.1.2 (For TPR-1600H, TPR-2000H) ……………………………………... 5-3
5.1.3 Safty protective device (suit every model)…………………………….……. 5-5
5.2 Instruction to switches ………………………………………………….. 5-6
5.2.1 (For TPR-1230, TPR-1230H) ………………………………………… 5-6
5.2.2 (For TPR-1600H, TPR-2000H) ………………………………………… 5-8
5.3
Installation of the clamp（work piece）………………………………. 5-9
5.3.1 General ……………………………………………………………………. 5-9
5.3.2 Introduction of the vise and the clamping of the work piece ………… 5-9
5.3.3 Universal clamp and the clamping of the work piece ……………….. 5-10
5.4 Installation and change of the drilling bit …………………………… 5-11
5.4.1 The assembly and disassembly of the drilling head and clamp ……… 5-11
5.4.2 The assembly and disassembly of the straight handle drill bit ……….. 5-13
5.5 Power on and off …………………………………………………………... 5-13
5.5.1 Power on …………………………………………………………………... 5-13
5.5.2 Power off …………………………………………………………………... 5-13
5.6 Work light …………………………………………………………………. 5-14
5.7 Cutting fluids ……………………………………………………………... 5-14
5.8 Elevating the arm …………………………………………………………... 5-14
5.9 Rotate the Gearbox right or leftwards ………………………………… 5-15
5.9.1
(For TPR-1230,TPR-1230H）………………………………….. 5-15
5.9.2
For TPR-1600H, TPR-2000H）……………………………………… 5-15
5.10 Rotate the arm forward or backwards ………………………………… 5-16
5.10.1 (For TPR-1230,TPR-1230H)……………………………………………….. 5-16
5.10.2 (For TPR-1600H, TPR-2000H)……………………………………………... 5-16
5.11 Change the spindle speed ………………………………………………. 5-17
5.11.1 (For TPR-1230,TPR-1230H) ……………………………………… 5-17
5.11.2 (For TPR-1600H, TPR-2000H) ……………………………………… 5-20
0-3
Section Content page
5.12 Automatic Feed ……………………………………………………………. 5-22
5.12.1
（For TPR-1230, TPR-1230H）………………………………………… 5-22
5.12.2
（For TPR-1600H, TPR-2000H）…………………………………….. 5-24
5.13 The spindle ………………………………………………………………... 5-25
5.14 Threading ………………………………………………………………….. 5-25
5.15 The assembly and disassembly of the work table …………………….. 5-25
5.16 Cutting fluids for all kinds of material ………………………………… 5-26
CHAPTER 6 Adjustment
6.1 General ……………………………………………………………………. 6-1
6.2 The arm clamping lever ………………………………………………… 6-1
6.2.1 (For TPR-1230, TPR-1230H) ………………………………………… 6-1
6.2.2 (For TPR-1600H, TPR-2000H) ………………………………………… 6-2
6.3 Adjust tighten the clamping device …………………………………… 6-3
6.3.1 (For TPR-1230, TPR-1230H) …………………………………… 6-3
6.3.2 (For TPR-1600H, TPR-2000H) ………………………………………. 6-3
6.4 Adjust tighten the clamping device …………………………………… 6-4
6.4.1 (For TPR-1230, TPR-1230H) …………………………………… 6-4
6.4.2 (For TPR-1600H, TPR-2000H) ………………………………………….. 6-5
6.5 Adjustment for the backlash between the gearbox and the arm rail………... 6-6
6.6 Adjustment of the hydraulic pressure ……………………………….… 6-6
6.7 Adjustment of the clutch(for TPR-1600H,TPR-2000H)……………………. 6-7
CHAPTER 7 Maintenance
7.1 General ……………………………………………………………………. 7-1
7.2 Daily Maintenance ………………………………………………………… 7-1
7.2.1 Clearing ……………………………………………………………………. 7-1
7.2.2 Please clean every parts using a metal brush and a rag, dipped with oil, to
rub them …………………………………………………………….………
7-1
7.2.3 The way to clean iron filings …………………………………………… 7-2
7.2.4 Lubrication …………………………………………………………………. 7-2
7.2.5 Change oil inside of the speed reduction of the arm elevating motor………. 7-3
7.2.6 Chang the oil inside the gearbox ……………………………………… 7-4
7.2.7 Changing hydraulic oil in the hydraulic oil pump………………………….. 7-5
7.3 Replace the cutting fluids ……………………………………………… 7-6
7.4 Maintenance and replacement period …………………………………. 7-6
7.5 Waste disposition …………………………………………………………... 7-6
0-4
Section Content page
CHAPTER 8 Troubleshooting
8.1 The spindle overloads and the relay jumps ……………………………. 8-1
8.1.1 The cause …………………………………………………………………... 8-1
8.1.2 The solution ………………………………………………………………... 8-1
8.2 The spindle overloads and the fuse burns out …………………………. 8-1
8.2.1 The cause …………………………………………………………….…… 8-1
8.2.2 The solution ………………………………………………………………... 8-1
8.3
What if the drill bit get broken？………………………………………. 8-2
8.4 What if the screw tap get broken? ……………………………………... 8-2
8.5 How if a person is entangled? …………………………………………. 8-2
CHAPTER 9 Annex
9.1 Electrical circuit diagram (For TPR-1230H CE Standard)……………….. 9-1
9.2 Electrical circuit diagram (For TPR-1230 CE Standard)…………….…… 9-2
9.3 Electrical circuit diagram (For TPR-1600H CE Standard)……………….. 9-3
9.4 Electrical circuit diagram (For TPR-2000H CE Standard)……………….. 9-4
9.5 Electrical main parts list (For TPR-1230H CE Standard)………………… 9-5
9.6 Electrical main parts list (For TPR-1230 CE Standard)……………..……. 9-7
9.7 Electrical main parts list (For TPR-1600H CE Standard)………………… 9-9
9.8 Electrical main parts list (For TPR-2000H CE Standard)………………… 9-11
9.9 Electrical circuit diagram (For TPR-1230 Standard)……………….…….. 9-13
9.10 Electrical circuit diagram (For TPR-1230 H Standard)…………………... 9-14
9.11 Electrical circuit diagram (For TPR-1600H, TPR-1600H Standard)……….. 9-15
9.12 Electrical main parts list (For TPR-1230 Standard)………………………. 9-16
9.13 Electrical main parts list (For TPR-1230H Standard)……………..……… 9-18
9.14 Electrical main parts list (For TPR-1600H Standard)…………….………. 9-21
9.15 Electrical main parts list (For TPR-2000H Standard)…………….………. 9-24
9.16 Diagram for hydraulic system (only for TPR-1230H)……………………… 9-27
9.17 Hydraulic system main parts list (only for TPR-1230H)…………………… 9-28
9.18 Diagram for hydraulic system (only for TPR-1600H)……………………… 9-29
9.19 Hydraulic system main parts list (only for TPR-1600H, TPR-2000H)……... 9-30
1-1
CHAPTR 1
Safety Guidelines
1.1 Please follow the below basic safety principles
(1) Have only sophisticated or experienced personal perform the machine operation or
maintenance.
(2) Please read and understand the operation manual thoroughly before operation.
(3) Please place the manual close to the machine for easy access.
(4) Please have only authorized person keep the keys to the machine.
(5) All operation and maintenance personnel need to know the location of the emergency
switch, its function and operation.
1.2 Precautions for the transportation and installation
(1) Please make sure that the floor is solid enough to support the machine.
(2) Only one person is allowed to lift and move the machine for safety reason.
(3) When lifting and moving, Nobody is allowed to be under or near the machine.
(4) Please wear protective helmet when moving, installing or clearing the machine.
(5) All levers, which tighten, need to be tightened.
(6) If the moving object weighs over 25kgs, Please use only proper movement equipment for it.
(7) Please make sure that the slings are strong enough to lift the machine or the subjects.
(8) Please power off before movement and installation. If necessary to power on, please let other
persons know the location of the emergent stop.
(9) Please put on leather gloves or similar protective equipments when moving, installing or
clearing the machine.
1.3 Precautions for operation
(1) Please don’t remove any protection guard or any safety installation.
(2) Please don’t remove or alter any location of the limit switches, restraint blocks or
interlocking mechanisms.
(3) Don’t touch any switch with wet hand.
(4) Please don’t put any part of your body on the moving parts of the machine or near to
them.
(5) The operation person have better no long hair, if it is impossible, please have it coiled in
a topknot and wear a safety helmet.
(6) Please wear no hand ring, watch, pearls or loose clothes. Operation should wear a safety
clothes.
(7) Please wear no slippery shoes while operating.
(8) Wearing gloves is needed when loading and unloading material.
(9) Only one person is allowed to operate the machine.
(10) While operation, Debris may fly off. So please wear a protective mask to prevent from
being injured.
(11) Please power off after work.
(12) Please wear a gauze mask if you are working, using cutting fluids.
(13) Please don’t use the machine in a explosive environment.
(14) A risk of being squeezed is composed when the gearbox and the arm are descending or
the spindle is descending to the worktable. (The arm screw moves at a low speed of
0.8m/min.)
(15) Operator should stand in front of the machine. That’s the operation position.
(16) Please clean with a vacuum sucker.
1-2
1.4 Precautions for checking and maintenance
(1) Please power off first before performing maintenance or checking job.
(2) Only have authorized electric technician carry out maintenance or checking job when
Power-on is needed in it
(3) Please power off after work.
(4) Adding or replacing hydraulic oil or lubricant, Please use Tailift recommended oil type
or its equivalent. For details, please refer to the chapter 7.
(5) Basically, only one person is needed to serve. If more than one person is called for,
Good communications is required.
(6) Please power off first before getting rid of the iron filings or cleaning the machine.
1-3
1.5 Warning labels and mark on the machine
1.5.1 Warning labels and mark introduction
labels Description
Please secure the machine with the base
fixing bolts, to prevent from any risk.
Model of a machine.
Please watch out the running tools.
Please operators wear protective
g
lasses
during work.
No polishing.
CE Mark
Oil filler position.
Oil drain outlet position.
1-4
Risk of high voltage.
Do not change speed while spindle is
running.
Main electrical switch.
1.5.2 Warning Labels and mark positions
a. The front view
1-5
b. The rear view
C. Oil filler position and Oil Drain outlet position
zArm elevating motor (For TPR-1230,TPR-1230H)
Dieses Handbuch passt für folgende Modelle
6
Inhaltsverzeichnis
