Sharp Carousel RK-42S24 Bedienungsanleitung
1
For Sharp Carousel®Built-in Kit
Models RK-42S24, RK-51S27,
RK-51K30, RK-51S30 or RK-51W30.
THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE OVENS
TO BE INSTALLED ABOVE CERTAIN CONVENTIONAL/CONVECTION
WALL OVENS. PLEASE SEE THE OPERATION MANUAL REGARDING
APPROVED BUILT-IN APPLICATIONS.
INSTALLATION INSTRUCTIONS
3
®
12
4567
NO. PART NAME QTY
PART CODE
1FRAME ASSEMBLY 1
S24 - FDECAB015MRY0
S27 - FDECAB008MRY0
S30 - FDECAB018MRY0
K30 - FDECAB019MRY0
W30 - FDECAB020MRY0
2EXHAUST DUCT ASSEMBLY 1
S24 - FDUC-B019MRK0
S27 - FDUC-B032MRK0
S30 - FDUC-B032MRK0
K30 - FDUC-B032MRK0
W30 - FDUC-B032MRK0
3POWER SUPPLY CORD 1
BOX ASSEMBLY
FCOVHB004MRK0
4REAR DUCT 1
PDUC-B072MRP0
5SCREW A 3
XCTSD40P10000
6SCREW B 2
XTTSD40P30000
7SCREW C 4
S24 - LX-CZB012MRE0
S27 - LX-CZB012MRE0
S30 - LX-CZB012MRE0
K30 - LX-CZB014MRE0
W30 - LX-CZB015MRE0
IMPORTANT:
This Built-in Kit is designed for and approved only for those Sharp
Microwave Ovens specifyingBuilt-InKitRK-42S24,RK-51S27, RK-51K30,
RK-51S30 or RK-51W30 on the rating label on the left side wall of the
oven cavity.
The cabinet or wall opening must be within the following dimensions:
RK-42S24 HEIGHT : 15 11/16" to 16"
WIDTH : 22 1/16" to 22 3/8"
DEPTH : minimum 19 1/4"
*RK-51S27, *RK-51K30, HEIGHT : 16 3/4" to 17"
*RK-51S30 & *RK-51W30 WIDTH : 24 3/8" to 24 11/16"
DEPTH : minimum 20"
*IFYOURLOWERCONVENTIONALOVENISNOT LISTEDINTHEOPERATIONMANUALOF
THE MICROWAVE OVEN AS AN APPROVED MAKE AND MODEL, THEN DO NOT INSTALL
THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM ARE
GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.
S= Stainless, K=Black, W=White
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE
BEGINNING INSTALLATION!
•Be sure to DISCONNECT THE PLUG of the microwave oven from the
electrical outlet before installing the Built-in Kit. Remove the Carousel
turntable from the oven cavity.
•Because the kit includes metal parts, due caution should be used in
handling and installation to avoid the possibility of injury.
2
C
4"
4" 6"
RK-42S24:
HEIGHT : 16 3/4" to 17"
WIDTH : 24 3/8" to 24 11/16"
DEPTH : minimum 20"
HEIGHT : 15 11/16" to 16"
WIDTH : 22 1/16" to 22 3/8"
DEPTH : minimum 19 1/4"
*RK-51S27,
*RK-51K30,
*RK-51S30&
*RK-51W30
1. Place the EXHAUST DUCT ASSEMBLY in the
opening. When the EXHAUST DUCT ASSEMBLY
is in the opening correctly, its flanges will be tightly
against the lower edge of the opening. See
Sketch 2.
2. Secure the EXHAUST DUCT ASSEMBLY with two
SCREWS B. See Sketch 2.
Sketch 1
Sketch 2
A
B
STEP 2 EXHAUST DUCT ASSEMBLY INSTALLATION
STEP 1 CABINET OR WALL OPENING
SCREW B
SCREW B
EXHAUST
DUCT ASSEMBLY
The opening in the wall or cabinet must be within the
following dimensions:
Outlet should NOT be in the shaded area as indicated
on Sketch 1.
NOTE 1: If the dimension of DEPTH (C) is more than
21", the outlet location may be any area on the
rear wall.
NOTE 2: Thefloor of the opening should be constructed
of plywood strong enough to support the
weight of the oven and floor load (about 100
pounds). The floor should be level for proper
operation of the oven. Be sure to check the
local building code as it may require that the
opening be enclosed with sides, ceiling and
rear partition. The proper functioning of the
oven does not require the enclosure.
3
STEP 3 POWER SUPPLY CORD BOX ASSEMBLY AND REAR DUCT INSTALLATION
1. Roll the power supply cord into the REAR DUCT.
2. Remove the screw ✪from left top of outer
cabinet. Secure the left flange of the REAR
DUCT with the screw ✪removed from the oven
and secure the right flange of the REAR DUCT
with SCREW A. See Sketch 3.
3. Plug the oven power supply cord into the
POWER SUPPLY CORD BOX ASSEMBLY
receptacle. See Sketch 4.
4. Slide the POWER SUPPLY CORD BOX
ASSEMBLY into the REAR DUCT and secure
the POWER SUPPLY CORD BOX ASSEMBLY
and REAR DUCT with two SCREWS A. See
Sketch 5. SCREW A
Sketch 3
REAR DUCT
✪
POWER SUPPLY
CORD BOX ASSEMBLY
Sketch 4
Sketch 5
REAR DUCT
SCREW A
POWER SUPPLY
CORD BOX ASSEMBLY
SCREW A
4
STEP 4 FRAME INSTALLATION
1. Placethe ovenadjacent tothewallorcabinet opening.Plugthe POWER
SUPPLY CORD BOX ASSEMBLY cord into the electrical outlet.
2. Carefully guide the assembled oven into the prepared opening. Slide
the oven on the EXHAUST DUCT ASSEMBLY. See Sketch 6. Avoid
pinching the cord between the oven and the wall.Adjust the position of
the oven so that the feet of the oven are fitted into the recesses of the
EXHAUST DUCT ASSEMBLY. See Sketch 7.
3. Position the FRAME ASSEMBLY to be square with the oven. Carefully
place the FRAME ASSEMBLY on the oven. Check that it is level and
then secure with two SCREWS C. See Sketch 8.
4. Secure the bottom portion of the FRAME ASSEMBLY with the two
remaining SCREWS C. See Sketch 8.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135 TINSEB279MRR0
Printed in U.S.A.
Sketch 6
FOOT
POWER SUPPLY CORD BOX
ASSEMBLY
RECESS
REAR DUCT ASSEMBLY
Sketch 7
EXHAUST DUCT ASSEMBLY
Sketch 8
For any other assistance or information about this kit, please call
Sharp’s Customer Assistance Center at
1-800-BE-SHARP (1-800-237-4277)
SCREW C
SCREW C
SCREW C
SCREW C
OVEN
Dieses Handbuch passt für folgende Modelle
4
Andere Sharp Mikrowellenofen Handbücher
Sharp
Sharp Carousel R-380L Bedienungsanleitung
Sharp
Sharp R-7H55 Bedienungsanleitung
Sharp
Sharp R-9360 Bedienungsanleitung
Sharp
Sharp R-405HK Bedienungsanleitung
Sharp
Sharp Carousel R-1751 Gebrauchs- und Pflegehandbuch
Sharp
Sharp R-612 Bedienungsanleitung
Sharp
Sharp R-34DM Bedienungsanleitung
Sharp
Sharp Carousel R-510FK Installations- und Betriebshandbuch
Sharp
Sharp R-401FK Betriebsanleitung
Sharp
Sharp R-395F(S) Bedienungsanleitung
Sharp
Sharp Microwave Drawer SMD2440JS Bedienungsanleitung
Sharp
Sharp R-642WE Bedienungsanleitung
Sharp
Sharp R-26ST-A Bedienungsanleitung
Sharp
Sharp SMD2480CSC Bedienungsanleitung
Sharp
Sharp R-82FBST Bedienungsanleitung
Sharp
Sharp R-8680(B) Bedienungsanleitung
Sharp
Sharp R-753M Bedienungsanleitung
Sharp
Sharp Carousel R-3S56 Bedienungsanleitung
Sharp
Sharp R-240D Gebrauchs- und Pflegehandbuch
Sharp
Sharp Carousel R-1512 Bedienungsanleitung
