Sharp R-9A11 Bedienungsanleitung

R-9All

R-9H?l

SHARP SERVICE MANUAL

R-9All

S9906R9Hll J//

CONVECTION

MICROWAVE OVEN

MODELS R-gAll

R-9Hll

In interests of user-safety the oven should be restored to its original

condition and only manufacturer original spare parts must be used.

(RD16101U)

This is a supplemental Service Manual for Model R-9All etc.

Those models are quite similar to Base Model R-9HlO (Refer No. is S9808R9Hl OJ//).

Use this supplemental manual together with the Base Model Service Manual.

Refer to the Base Model Service Manual for complete operation, service information, etc. (AD17101U)

TABLE OF CONTENTS Page

FOREWORD ....................................................................................................................................................... 1

CAUTION, MICROWAVE RADIATION .......................................................................................................... 1

PRODUCT DESCRIPTION ............................................................................................................................... 2

OPERATING INSUTRUCTIONS *

..................................................................................................................... 3

WIRING DIAGRAM .......................................................................................................................................... 4

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE ........................................................ 6

PICTORIAL DIAGRAM ..................................................................................................................................... 8

CONTROL PANEL CIRCUIT(R-SAII) ............................................................................. ..F........................... 9

CONTROL PANEL CIRCUIT(R-SHII) ....................................................................................................... IO

PRINTED WIRING BOARD .......................................................................................................................... 11

PARTS LIST .................................................................................................................................................... 12

PACKING AND ACCESSORIES ................................................................................................................... 18

SHARP CORPORATION

1 R-9All

R-9H11

---- -” jx. -* --a- \ “._ ____

R-9H 11

SERVICE MANUAL

SHARP

CONVECTION MICROWAVE OVEN

R-9A11/ R-9Hll

FOREWORD

This Manual has been prepared to provide Sharp Corp. Service

Personnel with Operation and Service Information for the

SHARP CONVECTION MICROWAVE OVENS, R-gAl I/

R-9Hll.

The Models R-gAl I/ R-9Hll are quite similar to Base Model

R-9HlO (Refer No. S9808R9Hl OJ//).

It is recommended that service personnel carefully study the

entire text of this manual and Base Model manual, so they will

be qualified to render satisfactory customer service.

Check interlock switches and door seal carefully. Special at-

tention should be given to avoid electrical shock and micro-

wave radiation hazard. (RD36102U)

CAUTION

MICROWAVE RADIATION

Personnel should not be exposed to the microwave energy

which may radiate from the magnetron or other microwave

generating devices if it is improperly used or connected. All

input and output microwave connections, waveguides, flanges

and gaskets must be secured. Never operate the device without

a microwave energy absorbing load attached. Never look into

an open waveguide or antenna while the ii:?yiice is energized.

Note( Parts List) : The parts marked ” %” are used in voltage

more than 250V. (RD36202U)

OSAKA, JAPAN (RD37201 U)

R-9A11

R-9Hll

PRODUCT DESCRIPTION

SPECIFICATIONS

ITEM

Power Requirements 240 Volts

50 Hertz

DESCRIPTION

Power Consumption

Power Output

Convection Power Output

Case Dimensions

Single phase, 3 wire earthed

1500W (Microwave)

16OOW (Convection)

750 watts nominal of RF microwave energy (2 litre water load)

Operating frequency of 2450M Hz

1500 Watts

Width 627mm

Height 378mm

Depth 481 mm

Cooking Cavity Dimensions Width 41 Omm

Height 245mm

Depth 41 Omm

Control Complement Touch Control System

Clock( I:00 - 12:59 )

Timer (0 - 99 min. 99sec. )

Microwave Power for Variable Cooking

Repetition Rate;

HIGH .................................

MED HIGH Full power throughout the cooking time

.*.*........................................... approx. 70% of Full Power

MED ....................................*..................... approx. 50% of Full Power

MED LOW (DEFROST) .......................... approx. 30% of Full Power

LOW *.....................*..........*........................

Convection Temperature for Variable Cooking approx. 10% of Full Power

CONVECTION .....................................

LOW MIX, 40 to 250 “C Temp. control

BAKE ...................

HIGH 180 “C with 10% microwave power

MIX, ROAST ...............

SLOW COOK 200 “C with 30% microwave power

............................... 130 “C for 4 hours

GRILL (no preheat)

..................................................................... 250 “C (preheat)

Variable cooking control pads,

SENSOR COOK pad (R-9Hll only)

AUTO START/CLOCK pad

EASY DEFROST pad,

ONE TOUCH REHEAT pad,

COMPU COOK pad,

STOP/CLEAR pad,

MEMORY pad

Set Weight INSTANT COOK/START pad

Approx. 30.0 kg

(RD44101

NOTE: Numbers and letters shown after sentences such as “RD44101 U” are for factory use only.

R-9All s

R-9Hll I

OPERATING INSTRUCTIONS

Touch Control Panel c

--3

{

-2

[

AUTO

COOK EASY :

REHEAT I-- EASY REHEAT PAD

Touch to select Easy Reheat

AUTO COOK PAD

Touch to select Auto Cook

mode r mode

.EASY REHEAT MENUS

EASY DEFROST PAD

Touch to defrost meat

tering weight only

AUTO COOK MENUS I

I by en-

CONVEC GRILL SLOW

COOK - CONVECTION COOKING

LOW MIX HIGH MIX FUNCTION PADS

BAKE ROAST Touch to cook for each func-

. ,.ST:<tI- ---8.,- . :. ;” L”,i”>:.L tion

1 I 1

NUMBER AND TEMPERATURE

PADS -

Touch to enter cooking times,

clock time, convection tem-

------I

perature or to select the Auto

Cook or Easy Reheat menus -.

1 4oc _

I 2 7ot I 3 130t -MEMORY PAD

Touch to enter one frequent-

ly used cooking programme.

Touch to recall the memorized

programme.

VARIABLE COOKING CON-

TROL PADS

Touch to select microwave

power setting. If not touched,

HIGH is automatically selec-

AUTO START/CLOCK PAD-

Touch to set clock or auto

start time

MORE( A 1, LESS( v 1 pads-

Touch to increase/decrease

the time in one minute incre-

ments during cooking or to in-

crease/decrease the time

whilst programming the Easy

Reheat, Auto Cook or Easy

Defrost modes.

STOP/CLEAR PAD

Touch to erase during

programming.

Touch once to stop operation

of oven during cooking; touch

twice to cancel cooking

programme.

LOWIMEDIMEDyEMqqy ted.

-INSTANT COOK/START PAD

>“i Touch once to cook for 1

.... _,,-,A-%,.qxq#..

i minute at HIGH or increase by

STOP INSTANT COOK 1 minute multiples each time

CLEAR START this pad is touched during

Lo microwave, convection, grill

L or mix cooking.

R-9All

Touch Control Panel

COMPU COOK PAD

Touch to select Compu

mode

SENSOR COOK PAD

Touch to select sensor cook

mode r Cook

COMPU COOK MENUS

SENSOR COOK MENUS .-I

EASY DEFROST PAD

Touch to defrost meat t

tering weight only 7y en-

ONE TOUCH REHEAT PAD

Touch to start automatic

heat cycle

NUMBER AND TEMPERATURE

pTtii&m[

categories.

AUTO START/CLOCK PAD

Touch to set clock or

start time

MORE( A I, LESS( v 1

Touch to increase/decrease

the time in one minute

ments during cooking or to

crease/decrease the

whilst programming the

Touch Reheat, Sensor Cook,

Compu Cook or Easy Defrost

modes.

STOP/CLEAR PAD

Touch to erase during

programming.

Touch once to stop operation

of oven during cooking; touch

twice to cancel cooking

programme.

14 150% 1 5 160% 1 6 ISO’C 1;

+ 7 200%18 220% 1 9 230% 1 ’

MEMORY PAD

Touch to enter one frequent-

ly used cooking programme.

Touch to recall the memorized

programme.

VARIABLE COOKING CON-

TROL PADS

Touch to select microwave

power setting. If not touched,

HIGH is automatically selec-

ted.

INSTANT COOK/START PAD

Touch once to cook for 1

minute at HIGH or increase by

1 minute multiples each time

this pad is touched during

microwave, convection, grill

or mix cooking.

Touch to start oven after set-

ting programmes.

INSTANT COOK 1

R-9Hll

OVEN

THEFIt.

CUT-01

15O’C

UPPER

LATCH

SWITCH

SCHEMATIC

NOTE: CONDITION

1. DOOR CLOSED

2. CLOCK APPEARS

A 240V-50Hz

MONITOR RESISTOR MONITOR SWITCH

o.f3/2ow

I OVEN LAMP

1 sd-bfi

CONTROL UN I T

DAMPER MOTOR

CONVECTION MOTOR

- TURNTABLE MOTOR

CONVECTION HEATER

$3 %:!FORMER

H-V. RECTIFIER L--Z-.,.-J

MAGNETRON

/ FM

THERM0

CUT- OUT

90’ c

1 OWER

LATCH

SWITCH

Figure O-1. Oven Schematic-OFF Condition

OVEN

THERM0

CUT-OUT

150’ c

UPPER

LATCH

SWITCH

SENSOR COOKING (R-9Hll)

L-

SCHEMATIC

NOTE: CONDITION

OF OVEN

1. DOOR CLOSED

2. “SENSOR COOK”

PAD TOUCHED

3. “START” PAD

TOUCHED

HIGH COOKING

SCHEMATIC

NOTE: CONDITION

OF OVEN

1. DOOR CLOSED

2. COOKING TIME

PROGRAMMED

3. VARIABLE COOKING

CONTROL “HIGH”

4. START PAD TOUCHED

H.V. RECTIFIER MAGNETRON

Euzu

2-L

-L-L

, M8A

MONITOR RESISTOR MONITOR SWITCH

o.a/2ow

240V-50th

BLU/l7 BRN/l7

pExq u

I’ FUSE

L OWEA

LATCH

SWIlCH

Figure O-2. Oven Schematic-High and Sensor Cooking Condition

ill 240V-50Hz

OVEN

MONITOR RESISTOR MONITOR SWITCH

0.8/2OW

OVEN

THERM0

CUT-OUT

15O’C

THERM0

CUT-OUT

15O’C

MONITOR RESISTOR MONITOR SWITCH

0.8/2OW /

‘IHERMO

CUT-OUT

90’ c

LOWER

LAlCH

SWllCH

OVEN LAMP

1HERMCl

CUT - OUT

90’ c

A-7 r-------

UPPER

LATCH

SWITCH

UPPER

LATCH

SWITCH LOWER

LATCH

SWllCH

‘ISToRui,-,

r-t E-5

SCHEMATIC

NOTE: CONDITION

OF OVEN

1. DOOR CLOSED

2. CONVECTION PAD

TOUCHED

3 DESIRED TEMP PAD

TOUCHED

4. START PAD TOUCHED

CONTROL UN1 T

CONVECTION MOTOR

TURNTABLE MOTOR

CONVECTION HEATER

A t

DM 1

r_PAMPER MOTOR

u TURNTABLE MOTOR

TRANSFORMER POWER

TRANSFORMER

MAGNETRON

H.V. RECTIFIER H.V. RECTIFIER MAGNETRON s

Figure O-4 Oven Schematic-Automatic Mix Cooking Condition

Figure O-3. Oven Schematic-Convection Cooking Condition

R-9All

R-9Hll

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDUR‘E

WARNING: To avoid possible exposure to microwave

energy;

A. Before operating the oven

1. Make sure that, when unlatching the door

slowly, an accompanying “click” indicating the

actuation of the monitor switch and latch

switches is heard.

2. Check visually the door seal for arcing and

damage.

. B. Do not operate the oven before any of the follow-

ing conditions are repaired;

1. Door does not close firmly against the front of

appliance.

2. There are a broken door hinge or support.

3. The door is bent or warped.

4. There is any defective parts in the interlock,

oven door or microwave generating and trans-

mission assembly.

5. There is any other visible damage to the oven.

C. Do not operate the oven

1. Without the RF gasket.

2. If the door is not closed.

CAUTION: DISCONNECT OVEN FROM POWER

SUPPLY BEFORE REMOVING

OUTER CASE. DISCHARGE HIGH

VOLTAGE CAPACITOR BEFORE

TOUCHING ANY OVEN COMPO-

NENTS OR WIRING. (RDA1203U)

OUTER CASE CABINET REMOVAL

To remove the outer case and proceed as follows;

1. Disconnect oven from power supply.

2. Remove eight (8) screws from the rear and along

the side edge of the case.

3. Remove the two (2) screws (LHSTIX LR-4) from

the lower portion of the oven cabinet back side.

4. Slide the entire case back about 3 cm to free it from

retaining clip on the cavity face plate.

5. Lift the entire case from the unit.

CAUTION: DISCHARGE THE HIGH VOLTAGE

CAPACITOR BEFORE TOUCHING

ANY OVEN COMPONENTS OR

WIRING.

Note: The outer case cabinet is secured by special

(LH) screw. When securing or loosening the

screw, LHSTIX (LR-4) type screw driver

should be used.

L&T/X SCREW DRIVER LHSTIX SCREW

(SIZE LR-4)

-1 \ 1,

Removal of LHSTIX screw at oven back side

LHSTIX screw driver and LHSTIX screw

R-9All I

I’?-9Hll i

Pull the wire leads from the oven lamp socket by

. . . . . . *.

pushtng the terminal hole ot the oven lamp socket

with the flat type small screw driver.

Lift up the tab of the oven lamp mounting plate

holding the oven lamp socket,

Slide the oven lamp socket left-ward

Now, the oven lamp socket is free.

CAUTION: When replacing the oven lamp socket, re-

place it so that the side where the black

dot is put faces left-ward.

OVEN LAMP SOCKET REMOVAL

Oven lamp socket

Flat type small

Terminal hole

Oven lamp socket

R-9All

R-9Hll

1 2 3 4 .I 5 6

cm‘\\

x?I”

r- 6

:iil

,’5

d m

“i

L D-

CCL

“I:

fi&

iI>

L-l

r’m$z

::&J

0yx$

was?:

zt-urn

-“OF;

$F’wc”

5 00 L

wma

=l-”

W-z,3

9020

evrna

X%28

4 I-

II!

2 ii

L ii

5 P

2 5

?I 4

sf-

#3S

&<O

2’”

22%

grs

ZjuLi.

-::

r?g

sol-

J?Llg

8Xx

2::

Z”a;

;

“5

-L

Dieses Handbuch passt für folgende Modelle

Andere Sharp Mikrowellenofen Handbücher

Sharp

Sharp R-880D Gebrauchs- und Pflegehandbuch

Sharp

Sharp R642WW Bedienungsanleitung

Sharp

Sharp R-600W Bedienungsanleitung

Sharp

Sharp Carousel R-7260 Bedienungsanleitung

Sharp

Sharp R-290H Bedienungsanleitung

Sharp

Sharp R242INW Bedienungsanleitung

Sharp

Sharp YC-MS01U Bedienungsanleitung

Sharp

Sharp SMC1585BB Bedienungsanleitung

Sharp

Sharp R-1490 Bedienungsanleitung

Sharp

Sharp R-530EK-T Bedienungsanleitung

Sharp

Sharp Carousel SMC1169HS Bedienungsanleitung

Sharp

Sharp R-677 Bedienungsanleitung

Sharp

Sharp R-772 Bedienungsanleitung

Sharp

Sharp R-212M Bedienungsanleitung

Sharp

Sharp R-810ES Bedienungsanleitung

Sharp

Sharp R-242 Bedienungsanleitung

Sharp

Sharp R-427DWM Bedienungsanleitung

Sharp

Sharp R-239 Bedienungsanleitung

Sharp

Sharp R-677W Bedienungsanleitung

Sharp

Sharp R-343 Bedienungsanleitung

Sharp

Sharp Carousel R-1211 Bedienungsanleitung

Sharp

Sharp Carousel R-431ZS Bedienungsanleitung

Sharp

Sharp R1871T Bedienungsanleitung

Sharp

Sharp SMD2499FS Bedienungsanleitung

Beliebte Mikrowellenofen Handbücher anderer Marken

Daewoo

Daewoo KOG-574R0S Bedienungsanleitung

LG MH7040SS Bedienungsanleitung

Dometic

Dometic DOTRM13W Bedienungsanleitung

Sanyo

Sanyo EM-X680 Bedienungsanleitung

KitchenAid

KitchenAid KMCX4510 Montageanleitung

Smeg

Smeg S45MCX1 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHM2044 Bedienungsanleitung

Sunbeam

Sunbeam SMW759 Bedienungsanleitung

Bosch

Bosch CEG732X.1B Bedienungsanleitung

Dometic

Dometic Roadmate 230 Bedienungsanleitung

Samsung

Samsung SJ0396W Bedienungsanleitung

Sanyo

Sanyo EM-P494WS Bedienungsanleitung

Electrolux

Electrolux EMS2840 Bedienungsanleitung

Daewoo

Daewoo KOC-984T2S13 Bedienungsanleitung

Impecca

Impecca CM07M2 Bedienungsanleitung

Sanyo

Sanyo EM-G5596V UK2 Bedienungsanleitung

Samsung

Samsung CE2927 Bedienungsanleitung

Cafe

Cafe CVM517P Bedienungsanleitung