Sharp AR-D29 Bedienungsanleitung

CODE : 00Z

qSERVICE MANUAL

CONTENTS

Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specified

ones for maintaining the safety and performance of the set.

SHARP CORPORATION This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

ARD29//A1E

LASER PRINTER OPTIONS

PAPER FEED UNIT

MODEL AR-D29

[1] PRODUCT OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[2] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

[3] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

[4] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . 4 - 1

[5] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . . 5 - 1

[6] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

[7] DISASSEMBLY AND ASSEMBLY, MAINTENANCE . . . . . . . . . 7 - 1

[8] BLOCK DIAGRAM, WIRING DIAGRAM,

CIRCUIT DIAGRAM, PARTS ARRANGEMENT. . . . . . . . . . . . . 8 - 1

PARTS GUIDE

AR-D29 PRODUCT OUTLINE

1 – 1

[1] PRODUCT OUTLINE

This unit is installed to one of the following machines to serve as a Paper feed module.

When installing one of the following machines, the stand with multi-purpose tray (AR-D29) must be installed in advance.

[2] CONFIGURATION

For combinations of options, refer to "C. List of combination of peripheral devices" described later.

Applicable models AR-M312U/AR-M420U

Upperexittray

(AR-TE4)

Finisher

(AR-FN6)

Mail-binstacker

(AR-MS1)

Standwithmultipurposedrawer

(AR-D29)

Scannerrack

(AR-RK2)

Saddlestitch

finisher

(AR-FN7)

Duplexmodule

(AR-DU3)

Duplexmodule/

bypasstray

(AR-DU4)

Exittray

(AR-TE3)

Rightupperexittray

(AR-TE5)

ScannermodulewithDSPF

(AR-EF6)

ScannermodulewithOC

(AR-EF5)

Punchunit

(AR-PN1A/B/C/D)

Power supply unit

(AR-DC1)

AR-D29 SPECIFICATIONS

3 – 1

[3] SPECIFICATIONS

Model name AR-D29

Type Stand with multi-purpose drawer

Transport speed To support 31-42 sheet/minute

Transport alignment Center alignment

Paper size A3, B4, A4, A4R, B5, B5R, A5R

11" x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11",

8.5" x 11"R, 5.5" x 8.5"R

Executive, Japanese p/c, Monarch (envelope)

Com-10 (envelope), DL (envelope),

C5 (envelope), ISO B5 (envelope)

How to change

the paper size Guide adjustment by user/

Software setting by user

Factory default paper size setting A3

Media available for paper feeding Plain paper : 60-128g/m² / 16-34lbs

Index paper : 176g/m² / 47lbs

Cover paper: 200-205g/m² / 54-55lbs

Envelope : 75-90g/m², 20-24lbs

Transparency film

*Media heavier than 105g/m² should be A4/8.5 x 11" or smaller. Media heavier than 128g/m² should be fed

from shorter edge.

*Only single paper feed is enabled for overlay copy or copy on back-side of printed paper.

Paper capacity Standard: 500sheets (80g/m²)

Post card: 40sheets

Envelope: 40sheets

Transparency film: 40sheets

Paper type Plain, recycled, pre-printed, pre-punched, color, letter head, labels, heavy, transparency, Japanese p/c, envelope

(User can set bi-type for each of the above paper type.)

Sizes to be detected Auto detection-AB: A3, B4, A4, A4R, B5, B5R, 8.5"x13", A5R

Auto detection-Inch: 11" x 17", 8.5" x 14", 8.5" x 11", 8.5" x 11"R, 7.25" x 10.5"R, 5.5" x 8.5R

Manual (input detection):

postal card, Monarch (envelope), Com-10 (envelope), DL (envelope), C5 (envelope), ISO B5 (envelope)

Ignore detection selectable:

Paper balance detection Provided (paper empty and 3 steps)

Paper loading system To be loaded from the upper side with front loading system

Tray ascent/

descent time Ascent Within 7 seconds

At paper empty, required time from tray insert to the empty detection

Descent Own weight descent

Dehumidification heater Not provided

Power consumption 24.5W or lower

Power source Supplied from main unit (DC24V 1A / DC5V 0.1A)

External dimensions 589 x 630 x 404 (mm)

Occupied dimensions 963 x 665 (mm)

Weight Approx. 25.2kg

AR-D29 UNPACKING AND INSTALLATION

4 – 1

[4] UNPACKING AND INSTALLATION

• Start installation after checking that the DATA and COMMUNICA-

TION indicators on the operation panel are neither lit nor blinking.

1) Turn off the main switch of the main unit of the printer.

Turn the main switch located on the front side of the printer to the

"OFF" position.

Then remove the power plug from the outlet.

2) Attach the adjusters and adjust them.

<1>Insert the left adjusters to the stand/paper drawer.

<2>Turn the each adjusters to lower them until they touch the floor.

*Be sure to attach the left adjuster to prevent overturning.

Caution: The lower tray cannot be pulled out unless the adjuster is low-

ered to the specified position.

3) Put the main unit of the printer on the stand/paper drawer.

<1>Pull out the paper tray of the main unit until it stops and then

remove it by lifting both ends of the tray.

<2>Hold the main unit of the printer at the positions shown in the illus-

tration and put the main unit on the stand/paper drawer so that the

front side and the left side of the main unit are aligned to those of

the stand/paper drawer.

Caution: For installation of the main unit, it must be held by two persons

and installed without haste.

4) Connect the main unit to the stand/paper drawer.

<1>Attach the rear mounting plates using a supplied screw for each.

Caution: Insert the rear mounting plates under the desk frame.

<2>Pull out the upper paper tray of the stand/paper drawer until it stops

and attach the front mounting plates using a supplied screw for each.

Then, remove the lock of the paper tray and close the tray.

Left adjuster: 1 pc. Front mounting

plates: 2 pcs. Rear mounting

plates: 2 pcs. Screws (M4x6):

4 pcs.

"OFF"

Frontside

Rearside

Rear mounting plate

Screw

Desk frame

Rear

mounting plate

Screw

Front

mounting plate

Front mounting

plate

AR-D29 UNPACKING AND INSTALLATION

4 – 2

<3>Reattach the paper tray of the main unit.

5) Connect the power supply I/F harness to the PCU PWB of the

main unit of the printer.

<1>Remove the screw that fixes the harness cover of the main unit of

the printer and slide the harness cover up to remove it.

Process the harness cover as shown in the illustration.

<2>Connect the connector of the relay harness of the multi purpose

drawer to the connector of the PCU PWB of the main unit of the printer.

<3>Reattach the power supply I/F harness cover to its original position

and fix it with the removed screw.

At this time, ensure that the power supply I/F harness are arranged

as shown in the illustration.

• Fix the harness securely to the wire saddle.

6) Attach the paper guides to the lower tray (large capacity tray) and

set the size.

Refer to "Setting and adjustment" described later.

*If another peripheral device must be installed, carry out the following

step at the end of the installation work.

7) Adjust the position of the paper guides of the upper paper tray of

the stand/paper drawer.

Refer to "Setting and adjustment" described later.

8) Carry out the off center adjustment.

Harness cove

Cut out.

Screw

CN10

Connector

Wire saddle

Harness cove

Screw

Wire saddle

AR-D29 EXTERNAL VIEWS AND INTERNAL STRUCTURES

5 – 1

[5] EXTERNAL VIEWS AND INTERNAL STRUCTURES

A. EXTERNAL VIEW

B. INTERNAL STRUCTURE

1 Multi-purpose tray (No. 2 tray) 2 Desk left door

1. MCPPD 5

1 Multi-purpose tray paper transport sensor (MCPPD) 4 Multi-purpose tray separation roller

2 Multi-purpose tray paper transport roller 5 Multi-purpose tray paper take-up roller

3 Multi-purpose tray paper feed roller 6 Multi-purpose tray

AR-D29 EXTERNAL VIEWS AND INTERNAL STRUCTURES

5 – 2

C. PWB, SENSOR

1.MCDRS

10.MCPWS

3.MCLUD

8.MCPED

2.MCSPD

12.MPTPWB

4.MCSS1

11.

5.MCSS2

7.MCSS4

6.MCSS3

9.MCPPD

No. Code Name Function Active condition Remark

1 MCDRS Side door open/close sensor Side door open/close detection H : Door closed

2 MCSPD MP tray remaining paper quantity sensor MP tray remaining paper quantity detection

3 MCLUD MP tray upper limit sensor MP tray upper limit detection H : Upper limit

detected

4 MCSS1 MP tray rear edge sensor 1 MP tray rear edge size detection L : When pressed In MP tray rear

edge size PWB

5 MCSS2 MP tray rear edge sensor 2 MP tray rear edge size detection L : When pressed In MP tray rear

edge size PWB

6 MCSS3 MP tray rear edge sensor 3 MP tray rear edge size detection L : When pressed In MP tray rear

edge size PWB

7 MCSS4 MP tray rear edge sensor 4 MP tray rear edge size detection L : When pressed In MP tray rear

edge size PWB

8 MCPED MP tray paper empty sensor MP tray paper empty detection L : Paper loaded

9 MCPPD MP transport sensor Detection of paper on the path L : Paper detected

10 MCPWS MP tray width sensor MP tray paper width detection Slide volume

11 MP tray rear

edge size PWB MP tray rear edge size PWB Multi-purpose tray rear edge size detection

12 MPTPWB MPT PWB

Distributed the power supply from the main

unit.

AR-D29 EXTERNAL VIEWS AND INTERNAL STRUCTURES

5 – 3

D. MOTOR, CLUTCH

2.MCLUM

3.MCPCL

4.MCM

1.MCFCL

No. Code Name Function Remark

1 MCFCL Multi-purpose transport clutch Clutch for transport from LCC desk

2 MCLUM Multi-purpose tray lift-up motor Multi-purpose tray lift-up

3 MCPCL Multi-purpose paper feed clutch Clutch for paper feed from Multi-purpose tray

4 MCM Multi-purpose transport motor LCC desk paper transport

AR-D29 ADJUSTMENTS

6 – 1

[6] ADJUSTMENTS

1. CHANGING THE PAPER SIZE

[Upper tray]

• A3 to A5R (11 x 7 to 5-1/2 x 8-1/2R) size plain paper can be set.

• Special paper can be set.

• Two maximum height lines are indicated: one for plain paper and one

for special paper.

Use the following procedure to change the size as needed.

1) Pull out paper tray.

If paper remains in the tray, remove it.

2) Adjust the guide plates A and B in the tray to the length and width of

the paper.

The guide plates A and B are slidable. Adjust them to the paper size

to be loaded while squeezing their lock levers.

3) Load paper into the tray.

Do not exceed red line when loading special paper to upper tray.

4) Gently push tray into the machine.

Push the tray firmly all the way into the machine.

5) Set the paper size.

Be sure to set the paper size and paper type referring to "2.Setting

the paper type and paper size".

If this is not done, paper misfeeds will occur.

2. SETTING THE PAPER TYPE AND

PAPER SIZE

Follow these steps to change the paper type setting if the paper type is

changed in either paper tray. For the paper types that can be used in

each tray.

1) Press the [CUSTOM SETTINGS] key.

The custom setting menu screen will appear.

2) Touch the [PAPER TRAY SETTINGS] key.

The paper tray selection screen will appear.

3) Touch the [TRAY SETTINGS] key.

4) Display the setting screen of the desired paper tray.

Touch the key or key to display the setting screen of the

desired paper tray.

Note: To automatically switch to a tray with the same size and type of

paper (if there is one) in the event that the paper tray runs out of

paper, display the last screen with the key and select [AUTO

TRAY SWITCHING].

5) Touch the [TYPE/SIZE] key.

6) Select the type of paper that was loaded in the tray.

Example: The paper type of tray 2 is selected

Touch the desired paper type to select it.

The paper size setting screen will appear.

PAPER TRAY

SETTINGS

ORWARD

RINT

PRINTER

CONDITION

TRAY SETTINGS

PAPER TRAY SETTINGS

CUSTOM SETTINGS

1/4

PLAIN / A4

PAPER TRAY SETTINGS

TYPE / SIZE

CUSTOM SETTINGS

TRAY 1

FAX I-FAX

COPY

DOC.

FILING

FIXED PAPER SIDE

DISABLE DUPLEX

DISABLE STAPLE

DISABLE PUNCH

TYPE / SIZE

TRAY 2

PER TRAY SETTINGS

COPY

I-FAX DOC.

FILING

FAX

PLAIN / A4

CANCEL

1/2

PLAIN

RECYCLED

PRE-PRINTED PRE-PUNCHED

LETTER HEAD

COLOUR

HEAVY PAPER ENVELOPE

LABELS

TRANSPARENCY

TRAY 2 TYPE/SIZE SETTING

SELECT THE PAPER TYPE.

CUSTOM SETTINGS

1/2

AR-D29 DISASSEMBLY AND ASSEMBLY, MAINTENANCE

7 – 1

[7] DISASSEMBLY AND ASSEMBLY, MAINTENANCE

A. MAJOR PARTS AND SIGNAL FUNCTIONS

Code Name Function Remark

MCDRS MP door open / close sensor MP left door open / close detection

Control PWB Control PWB Communication with the machine,

machine operation control

MCSPD MP tray remaining paper quantity sensor MP tray remaining paper quantity detection

MCLUD MP tray upper limit sensor MP tray upper limit detection

MDSS1 MP tray rear edge sensor 1 MP tray rear edge size detection In MP tray rear edge size PWB

MCSS2 MP tray rear edge sensor 2 MP tray rear edge size detection In MP tray rear edge size PWB

MCSS3 MP tray rear edge sensor 3 MP tray rear edge size detection In MP tray rear edge size PWB

MCSS4 MP tray rear edge sensor 4 MP tray rear edge size detection In MP tray rear edge size PWB

MCPED MP tray paper empty sensor MP tray paper empty detection

MCPPD MP transport sensor Detection of paper on the path

MCPWS MP tray width sensor MP tray paper width detection Slide volume

MP tray rear

edge size PWB MP tray rear edge size PWB MP tray rear edge size detection

MCFCL Multi-purpose tray transport clutch Multi-purpose tray transport clutch

MCLUM Multi-purpose tray lift-up motor Multi-purpose tray lift-up

MCPCL Multi-purpose paper feed clutch Clutch for paper feed from Multi-purpose tray

MCM Multi-purpose tray transport motor Multi-purpose tray paper transport

MCM

MCDRS

MCSPD

MCSPD MCLUD

MCPED

MCSS2

MCSS4

MCSS1

MCSS3

MCPPD

MCPWS

MCLUM

MCFCL

MCPCL

MPT LD PWB

MPT PWB

+5V

MCPWS

+5V

MCPPD

+5V

CN-E

+5V

VAREF

MCPED

N.C.

MCPWS2

MCLUD

+5V

MCDRS

MCSPD

PHDR-14VS-1

MCSS2

MCSS1

GND2

CN-F

MCSS3

MCSS4

GND2

PHDR-12VS-1

24V 1

MCLUM/ 2

PHR-2

MCPCL/

+24V

MCFCL/

+24V

MCM/

GND1

+24V

MCM-T

MCMCLK/

PHR-9

SMR-02V-B

SMR-02V-NSMP-02V-NC

SMP-02V-BC

SRA-21T-4

MCLUM/

24V

MCSS2

MCSS3

MCSS4

N.C.

MCSS1

GND2

PHR-6

PHR-2

MCMCLK/

MCM/

GND1

MCM-T

+24V

PHR-5

SMP-03V-BC SMR-03V-B

GND2

MCLUD

MCPPD

+5V

GND2

3 GND2

MCSPD

+5V

CN-D

CN-A

SMR-18V-BSMP-18V-BC

GND23

MCPED

+5V

MCDRS

+5V

MCPWS2

MCPWS

VAREF

Inhaltsverzeichnis

Andere Sharp Drucker Handbücher

Sharp

Sharp MX-M182 Bedienungsanleitung

Sharp

Sharp PR-45M Bedienungsanleitung

Sharp

Sharp SF-2014 Bedienungsanleitung

Sharp

Sharp AR-5618 Bedienungsanleitung

Sharp

Sharp AR-M350N Bedienungsanleitung

Sharp

Sharp AR-M280 Bedienungsanleitung

Sharp

Sharp AR-C260P Bedienungsanleitung

Sharp

Sharp FACSIMILE UX-2200CM Bedienungsanleitung

Sharp

Sharp AJ-1100 Einrichtungshandbuch

Sharp

Sharp AL-840 - B/W Laser Printer Bedienungsanleitung

Sharp

Sharp CE-515P Bedienungsanleitung

Sharp

Sharp MX-C400P Installations- und Betriebsanleitung

Sharp

Sharp Network Scanner Bedienungsanleitung

Sharp

Sharp DP-750 Bedienungsanleitung

Sharp

Sharp AR-P350 Bedienungsanleitung

Sharp

Sharp MZ-80P6 Bedienungsanleitung

Sharp

Sharp MX-M350-U Bedienungsanleitung

Sharp

Sharp AR-3551 Bedienungsanleitung

Sharp

Sharp AJ-2200 Bedienungsanleitung

Sharp

Sharp MZ-80P5 Bedienungsanleitung

Sharp

Sharp AJ-6110 Einrichtungshandbuch

Sharp

Sharp DX-C200 Bedienungsanleitung

Sharp

Sharp CE-140P Bedienungsanleitung

Sharp

Sharp AR-C200P - Color Laser Printer Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung