Sharp AR-MS1 Bedienungsanleitung

This document has been published to be used for

after sales service only.

The contents are subject to change without notice.

Parts marked with “ “ are important for maintaining the safety of the set.

Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION

LASERPRINTEROPTIONS

MAILBINSTACKER

MODEL AR-MS1

CODE : 00ZARMS1//A1E

[1] PRODUCT OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[2] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

[3] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

[4] UNPACKING AND INSTALLATION. . . . . . . . . . . . . . . . . . . . . . 4 - 1

[5] EXTERNAL VIEWS AND INTERNAL STRUCTURES. . . . . . . 5 - 1

[6] MACHINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

[7] DISASSEMBLY AND ASSEMBLY, MAINTENANCE. . . . . . . . . 7 - 1

[8] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1

CONTENTS

AR-MS1

     

AR-MS1 PRODUCT OUTLINE, CONFIGURATION 1-1

[1] PRODUCT OUTLINE

This unit is a paper exit unit, which allows to select a desirable tray in two or more paper exit trays (male bins), when installed to the following machines.

[2] CONFIGURATION

1. Before installation of this unit, one of the multi-purpose tray (AR-MU1), the large capacity paper feed desk (AR-D13), and the 3-stage paper feed

desk (AR-D14) must be installed.

2. When installing this unit together with the AR-MJ1, it may be required to install the optional power unit (AR-DC1) together.

3. This unit cannot be installed together with the finisher (AR-FN6) or the paper exit extension tray (AR-TE4) .

Applicable models AR-P350 / P450, AR-M350 / M450

Output units

AR-MS1

Scanner rack

Mail-bin stacker

=Any of the units must be installed together.

Multi purpose drawer

Stand/3 x 500 sheet paper drawer

Stand/MPD & 2000 sheet

Duplex module/bypass tray

Duplex module

B/W scanner module/DSPF

Saddle stitch finisher

Finisher

Mail-bin stacker

Exit tray

Punch unit

PS3 expansion kit

Facsimile expansion kit

Print server card

Hard disk drive

Power supply unit

Upper exit tray extension

Multi-function controller board

Fax memory (8 MB)

Network scanner expansion kit

B/W scanner module/DSPF(AR-EF1)

Upper exit tray

extension

(AR-TE4)

Finisher

(AR-FN6)

Mail-bin stacker

(AR-MS1)

Stand/MPD & 2000 sheet

paper drawer

(AR-D13)

Power supply unit

(AR-DC1)

Multi purpose drawer

(AR-MU1)

Stand/3 x 500 sheet

paper drawer

(AR-D14)

Saddle stitch

finisher

(AR-FN7)

Duplex

module/bypass tray

(AR-DU4)

Exit tray

(AR-TE3 or AR-DU4 Standard)

Duplex module

(AR-DU3)

Simultaneous installation not allowed

Simultaneous installation is required

    ! "#$%&'

AR-MS1 SPECIFICATIONS 3-1

[3] SPECIFICATIONS

1. Basic

Type Desktop type mail bin stacker with 8-exit-tray

Transport speed To support 35-45 sheet/minute

Transport alignment Center alignment

Tray type

(No. of tray) Upper

tray EXIT tray

Lower

Tray Mail bin tray (7 stages)

Output paper

capacity Upper

tray 250 sheets (A4/8.5"x11", 80g/m²)

Lower

Tray 100 sheets/bin (A4/8.5"x11", 80g/m²)

Output paper delivery Face-down

Output paper

size Upper

tray A3, B4, A4, A4R, B5, B5R, A5R

11"x17", 8.5"x14", 8.5"x13", 8.5"x11",

8.5"x11"R,5.5"x8.5"R,

Executive, Japanese post card,

Monarch(98x191),Com-10(105x241),

DL(110x220),C5(162x229),

ISO B5(176x250)

Lower

Tray A3, B4, A4, A4R, B5, B5R

11"x17", 8.5"x14", 8.5"x13",

8.5"x11", 8.5"x11"R,

Executive

Specofmedia

for paper

output

Upper

tray Tracing paper:52-59g/m² / 14-15lbs

Plain paper:60-128g/m² / 16-34lbs

Index paper:176g/m² / 47lbs

Cover paper:205g/m² / 54-55lbs

Transparency

Lower

Tray Plain 60-105g/m² / 16-28lbs

Remaining

paper

detection

Upper

tray Not Provided

Lower

Tray Not Provided

Exit tray full

detection Upper

tray Provided

Lower

tray Provided

Power consumption Less than about 20.2W

Power source Supplied from the optional power source

(DC24V 0.8A / DC5V 0.2A)

External

dimensions(WxDxH) 465x530x508 (mm)

Occupied

dimensions(WxD) 465x530 (mm)

Weight Approx. 19kg

      !"#$%&

AR-MS1 UNPACKING AND INSTALLATION 4-1

[4] UNPACKING AND INSTALLATION

•Start installation after checking that the DATA and COMMUNICATION

indicators on the operation panel are neither lit nor blinking.

•For installation of AR-MS1, an optional stand/paper drawer (stand/MPD

& 2000 sheet paper drawer, stand/3 x 500 sheet paper drawer or multi

purpose drawer) must have been installed.

Also if a multi purpose drawer has been installed, a power supply unit

(AR-DC1) is needed additionally.

1) Turn off the main switch of the main unit of the printer.

Turn the main switch located on the front side of the main unit to the

"OFF" position.

Then, remove the power plug of the main unit from the outlet.

2) Remove the upper cabinet of the stand/paper drawer.

<1>Pull out the paper tray of the stand/paper drawer.

Remove the four screws of the cabinet attached to the right side of

the main unit of the printer and remove the cabinet.

<2>Mount screw B to the position shown in the illustration.

3) Attach the mail-bin stacker.

<1>Remove the paper exit actuator from the main unit of the printer.

<2>Raise the relay unit at the side of the mail-bin stacker.

Caution: Do not press on the relay unit while it is raised.

(Doing so may deform or damage the unit.)

<3>Hold the grip of the mail-bin stacker and place the mail-bin stacker

on the stand/paper drawer temporarily.

<4>push the lower part to attach the mail-bin stacker by sliding it toward

the exit tray of the main unit. At this time, align the mail-bin stacker

with the exterior line of the stand/paper drawer.

Mounting plates: 2 pcs.

Tray: 1 pc.

Screw B: 1 pc.

Screws A (M4x8): 5 pcs.

"OFF"

Cabinet

Screw B

Actuator

Relay unit

Push.

Place.

Grip

    "# $%&'()

AR-MS1 UNPACKING AND INSTALLATION 4-2

<5>Open the front cover of the mail-bin stacker and fix the stacker with

three screws A at the positions shown in the illustration.

<6>Then, close the front cover and close the paper tray of the stand/

paper drawer.

<7>Attach the mounting plates to the positions shown in the illustration

and fix them with screws A.

Caution: Insert the mounting plate under the desk frame.

4) Attach the tray.

Steps 5) and after are the procedure to be carried out when a multi

purpose drawer has been installed.

If a stand/MPD & 2000 sheet paper drawer or a stand/3 x 500 sheet

paper drawer has been installed, carry out steps 8) and after.

5) Process the AC inlet cover attached to the rear cabinet of the stand/

paper drawer.

<1>Remove the two screws that secure the rear cabinet and remove the

rear cabinet.

<2> Remove the screw that fixes the AC inlet cover and then remove the

AC inlet cover.

Process the AC inlet cover as shown in the illustration.

6) Attach the power supply unit.

Attach the power supply unit to the hanging portions and secure it

using the supplied three screws.

7) Connect the power supply unit harness to the PCU PWB of the main

unit of the printer.

<1>Connect the power supply unit harness to the PCU PWB of the main

unit of the printer.

Screw A

(Front side)

Mounting plate

Screws A

(Rear side)

Desk frame

Mounting plate

Tray

Cut out.

AC inlet cover

Screw

Rear

cabinet

Optional power supply unit

Screws

Screw

Hanging portion

Harness cover

Screw

 *   "# $%&'()

AR-MS1 UNPACKING AND INSTALLATION 4-3

<2>Connect the power supply unit harness connector to CN11

(red connector) of the PCU PWB of the main unit of the printer.

<3>Reattach the harness cover to its original position and fix it with the

removed screw.

At this time, ensure that the power supply unit harness is arranged

as shown in the illustration.

* Fix the harness securely to the wire saddle.

8) Remove the AC inlet cover and then remove the rear cabinet of the

stand/paper drawer.

<1>Remove the screw that fixes the AC inlet cover and then remove the

AC inlet cover.

<2>Remove the AC cord of the power supply unit from the inlet

connector of the main unit of the printer.

Remove the four screws thatfix the rear cabinet andthen remove the

rear cabinet.

9) Arrange the harness of the mail-bin stacker.

<1>Pass the harness of the mail-bin stacker between the power supply

unit and the frame of the stand/paper drawer and connect it to the

connector of the power supply unit.

<2>Fit the snap band attached to the mail-bin stacker at the position

shown in the illustration to fix the harness.

10) Attach the rear cabinet of the stand/paper drawer.

<1>Pass the AC cord of the power supply unit as shown in the illustration

and fix the rear cabinet of the stand/paper drawer with the screws.

<2>Attach the AC inlet cover to the rear cabinet of the stand/paper

drawer and fix it with the removed screw.

11) Connect the AC cord of the optional power supply unit to the main

unit of the printer.

<1>Connect the AC cord of the power supply unit to the inlet connector

of the main unit of the printer at the location shown in the illustration.

Connector

CN11

Wire saddle

Harness cover

Optional power

supply harnesses

Screw

Wire saddle

Screw

AC inlet cover