Sharp Notevision PG-A20X Bedienungsanleitung

Quick Start Reference Sheet

Sharp PG-A20X

Revision A

DR-SHP29 – 4/27/04 SP Controls reserves the right to modify specifications without notice at any time.

NOTE: This one-page document is intended only as a quick reference for installation – please read

the SP Controls Application Note for a complete description of this projector driver prior to installation.

I. Driver Features

1. Input Selection Mapping

Selection 1: VIDEO

Selection 2: S-VIDEO

Selection 3: RGB

Selection 4: RGB

2. Hidden Function Mapping (Default Configuration)

Using the ON button as a shift key, press the following buttons to access the specified projector features.

Selection 1: BLANK SCREEN

Selection 2: ENTER

Selection 3: ADJ LEFT

Selection 4: ADJ RIGHT

Off: MENU

Volume Up: ADJ UP

Volume Down: ADJ DOWN

3. Other Driver Features

Power Status Feedback Method RS-232 Power Polling

Control Wiring: RS-232 and IR-Emitter

II. Wiring Specifications

NOTE: For a wiring diagram, please see the SP Controls Application Note.

1. RS-232:

Wire the Panel RS-232 port to a female DB9 as follows:

TX to 2

RX to 3

GND to 5

Connect this female DB9 to the included Sharp intermediate cable (labeled RS-232C) and connect

the mini-DIN end of the adapter to the projector port labeled RS-232C IOIOI.

2. Infrared Emitter:

Wire the Panel IR/Serial port to a female 1/8" Mini as follows:

IR/SER to tip

GND to ring

Connect to the included IR Emitter and attach the emitter bud to any projector IR window.

III. Additional Projector Information

The A20X can be configured with an Economy Mode, which determines whether or not the projector

shuts itself off in the absence of an input signal.

When installing the A20X, you should set the Economy Mode to OFF. This disables the Sharp’s

Automatic Power Shutoff feature.

Economy Mode is set via on screen menus, Options: Economy Mode. Access the onscreen menus with

either the SmartPanel’s hidden functions, or the Sharp’s remote control.

Projector Driver Application Note

Sharp PG-A20X

Revision A

DR-SHP29 – 4/27/04 SP Controls reserves the right to modify specifications without notice at any time.

This document describes the SmartPanel Projector Driver for the Sharp PG-A20X projector. For

information on configuring and using the Panel see the SmartPanel Configuration and Installation Guide.

Please read the SPECIAL CONTROL NOTE in the Control Wiring section of this document before

attempting control of the projector. This note describes how the Sharp’s Economy Mode impacts the

projector’s behavior.

I. PROJECTOR CONTROL

A. Volume and Power Control

Volume control on the Sharp is absolute. Absolute volume control is also possible with SP Controls’

option Audio Follow Video Preamplifer (SP3-AFVP+).

B. Input Selection Mapping

The following table specifies the factory-preset input mapping for this Driver. The Configuration Utility

can be used to customize these settings your installation.

Selection 1: VIDEO

Selection 2: S-VIDEO

Selection 3: RGB

Selection 4: RGB

Input choices available for the Sharp with this

Driver are VIDEO, S-VIDEO, and RGB.

C. Hidden Function Mapping

The following table specifies the factory preset hidden function mapping for this Driver. The

Configuration Utility can be used to customize these settings your installation.

Selection 1: BLACK SCREEN

Selection 2: ENTER

Selection 3: ADJUST LEFT

Selection 4: ADJUST RIGHT

Off: MENU

Volume Up: ADJUST UP

Volume Down: ADJUST DOWN

Hidden functions names are based on the Sharp remote and controls on top of the projector. Hidden

functions are accessed by pressing the indicated key while the holding the On key down.

ADJUST controls, ENTER and UNDO navigate through onscreen menus. UNDO is a “return to previous

menu” or “back” command. MENU can also be used as UNDO. The area zoomed with the ENLARGE

function can be moved using the ADJUST keys.

BLACK SCREEN is a toggle.

Projector

Ready

Warm-up

OFF

Volume

VIDEO

S-VIDEO RGB RGB

Projector

Ready

Warm-up

OFF

Volume

ADJUST

DOWN

BLACK

SCREEN

ENTER ADJUST

LEFT ADJUST

RIGHT

SmartPanel Projector Driver Application Note Sharp PG-A20X

AUTO SYNC only works when an RGB input is selected.

The hidden functions available for the Sharp with this Driver are as follows:

ADJUST LEFT

ADJUST RIGHT

ADJUST UP

ADJUST DOWN

AUTO SYNC

KEYSTONE

FREEZE

ENLARGE

RESIZE

ENTER

UNDO

BLACK SCREEN

D. Relays

The following table specifies the factory preset

settings for the low-current relays found on the rear

of the SmartPanel. The Configuration Utility can

be used to customize these settings your installation.

Relay 1 ON Maintained

Relay 2 ON Momentary

Relay 3 OFF Momentary

Selection Momentary; not Binary

E. Other Presets

The following table specifies other default factory settings for this Driver that affect is control of the

Projector.

Power Status Feedback Method Power Polling (see note 1)

Control Wiring RS-232 and Infrared Emitter

(see note 2)

Control for the Sharp with this Driver is via RS-232 and Infrared Emitter

The following table specifies settings for the Panel’s configurable timers. For more information on the

inactivity shutdown feature and the lockout timer see the SmartPanel Configuration and Installation

Guide.

Lockout Timer 70 seconds (see note 3)

Inactivity Shutdown Disabled

RELAYS

PWR

MAINT.

PWR

MOM.

PWR

OFF

MOM.

SELECTION

(EXT. SWITCHER CTRL)

4321

500mA MAX. CURRENT

SmartPanel Projector Driver Application Note Sharp PG-A20X

II. CONTROL WIRING

PROJECTOR CONTROL

RS232 IR/SERIAL

GND

CTS

RTS

+12V

GND

IR/SER

SENSE

Female DB9

RS-232 to

RS-232C

1/8" Mini

Female

IR Emitter to

any window

Sharp Male DB9 to Male MiniDIN adaptor

(included with Sharp projector, labeled RS-232C)

54321

9876

54321

IR Emitter

(included with Panel)

TX to 2

RX to 3

GND to 5

This section specifies how RS-232 and the Infrared Emitter

should be wired to the Sharp projector.

A. RS-232 should be connected to the Sharp control port

labeled RS-232C. Connection should be as follows:

1. Wire the Panel to a female DB9 as follows:

TX to 2

RX to 3

GND to 5

2. Connect this female DB9 to the Sharp’s custom DB9 to

mini-DIN adapter cable. This cable is included with the

Sharp and is labeled RS-232C.

3. Connect the Sharp custom cable to the projector port

labeled RS-232C IOIOI.

B. Infrared should be wired to any Sharp infrared port.

Connection should be as follows:

1. Wire the Panel to a female 1/8" Mini as shown; wire

IR/SER to tip and GND to ring. Direct wiring to the IR

Emitter is not recommended as it makes removal of the

Panel for service more difficult.

2. Attach to any projector IR port using the Panel’s IR

Emitter (included with the Panel).

Note that the emitter glows red when IR is emitted so wiring

can be verified.

SPECIAL CONTROL NOTE

Read before attempting to control the projector

The A20X can be configured with an Economy Mode,

which determines whether or not the projector shuts itself

off in the absence of an input signal.

When installing the A20X, you should set the Economy

Mode to OFF. This disables the Sharp’s Automatic

Power Shutoff feature.

Economy Mode is set via on screen menus, Options:

Economy Mode. Access the onscreen menus with either

the SmartPanel’s hidden functions, or the Sharp’s remote

control.

Questions should be directed to SP Controls technical

support at [email protected].

SmartPanel Projector Driver Application Note Sharp PG-A20X

III. TROUBLESHOOTING

Additional tips can be found in the SmartPanel Configuration and Installation Guide.

The Projector keeps turning itself off!

Verify that the A20X’s Economy Mode is set to OFF as explained in the Special Note in the Control

Wiring section of this document. If the Economy Mode is on, the projector will shut itself off after

fifteen minutes. If power polling or a third party power current sensor is being used (e.g., AMX-PCS),

the Panel will automatically shut itself off also. If not, the Panel will remain on and you will have to

power the Panel off with the Off button and wait until the lockout timer expires before you can re-

power the projector.

The Panel does not do anything at all.

When power is applied to the Panel it should run through a brief power on self-test, during which all of

the Panel lights will turn on and off in sequence. If you do not see this self test, make sure power is

connected correctly and that polarity is correct.

The Panel keeps turning itself off even though the projector is on.

The Panel turns itself off when power status feedback indicates that the projector is off. If a third

party power current sensor is being used, check to make sure that it is correctly wired, and that it is

correctly calibrated according to the manufacturer’s instructions. If not, make sure that the Panel is

configured with None or Power Polling under power status feedback in the Configuration Utility’s

Wiring Options tab.

IV. TECHNICAL NOTES

1. By default, projector power is verified by polling every few seconds via the RS-232 port. Power

polling can be suspended by depressing and holding the On key; polling will be restored when the

key is released. Should the Sharp power off, the Panel will usually detect this condition and power

off within twenty seconds. Should the Sharp power on, the Panel will usually detecting this condition

and power on within ten seconds.

2. The Sharp is controlled via RS-232 and Infrared/Wired Remote with this Driver. A discussion of the

advantages of Wired Remote versus IR can be found in the SmartPanel Configuration and

Installation Guide.

3. The lockout timer specifies the amount of time allowed between sending POWER OFF and POWER

ON to the projector (the delay allows the projector bulb to cool before re-powering). This delay can

be configured using the Configuration Utility; however, adjusting the lockout timer delay is

strongly discouraged as rapid re-powering causes undue wear on the projector’s bulb. Also, the

Sharp will not allow power to be restored before a minimum delay has expired. Therefore, disabling

the lockout delay will cause potentially confusing Panel behavior.

V. REVISION HISTORY

1. Revision A (April, 2004) Original release.

Andere Handbücher für Notevision PG-A20X

Inhaltsverzeichnis

Andere Sharp Projektor Handbücher

Sharp

Sharp Notevision PG-D2510X Bedienungsanleitung

Sharp

Sharp PG-F320W - Notevision WXGA DLP Projector Bedienungsanleitung

Sharp

Sharp Notevision XG-NV7XE Bedienungsanleitung

Sharp

Sharp XV-Z20000 Bedienungsanleitung

Sharp

Sharp PGF267X - XGA DLP Projector Bedienungsanleitung

Sharp

Sharp Notevision XG-C335X Benutzerhandbuch

Sharp

Sharp PG-A10X - Notevision XGA LCD Projector Bedienungsanleitung

Sharp

Sharp Conference Series Bedienungsanleitung

Sharp

Sharp XV-Z12000 - Vision - DLP Projector Bedienungsanleitung

Sharp

Sharp PG-A10X-A Bedienungsanleitung

Sharp

Sharp XG-MB67X Benutzerhandbuch

Sharp

Sharp XG-MB55X Bedienungsanleitung

Sharp

Sharp EL-99T Bedienungsanleitung

Sharp

Sharp XG-C40XU-S - Notevision XGA LCD Projector Bedienungsanleitung

Sharp

Sharp XV-Z12000 - Vision - DLP Projector Bedienungsanleitung

Sharp

Sharp XG-E3500U Bedienungsanleitung

Sharp

Sharp Notevision XR-1X Bedienungsanleitung

Sharp

Sharp XG-MB70X Bedienungsanleitung

Sharp

Sharp Notevision XG-C335X Bedienungsanleitung

Sharp

Sharp Notevision PG-B10S Bedienungsanleitung

Sharp

Sharp PG-C45X - Notevision XGA LCD Projector Bedienungsanleitung

Sharp

Sharp Notevision XR-55X Bedienungsanleitung

Sharp

Sharp XG-V10XU - Conference Series XGA LCD... Bedienungsanleitung

Sharp

Sharp PGF310X - Notevision XGA DLP Projector Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung