Sharp PG-M20 Series Bedienungsanleitung
Quick Start Reference Sheet
Sharp PG-M20x
Revision A
DR-SHP20 – 9/17/03 SP Controls reserves the right to modify specifications without notice at any time.
NOTE: This one-page document is intended only as a quick reference for installation – please read
the SP Controls Application Note for a complete description of this projector driver prior to installation.
I. Driver Features
1. Input Selection Mapping
Selection 1: DVI
Selection 2: S-VIDEO
Selection 3: VIDEO
Selection 4: VIDEO
2. Hidden Function Mapping (Default Configuration)
Using the ON button as a shift key, press the following buttons to access the specified projector features.
Selection 1: ENTER
Selection 2: UNDO
Selection 3: ADJ LEFT
Selection 4: ADJ RIGHT
Off: MENU
Volume Up: ADJ UP
Volume Down: ADJ DOWN
3. Other Driver Features
Power Status Feedback Method Sensor
Control Wiring: IR-Emitter
II. Wiring Specifications
NOTE: For a wiring diagram, please see the SP Controls Application Note.
1. Infrared Emitter:
Wire the Panel IR/Serial port to a female 1/8" Mini as follows:
IR/SER to tip
GND to ring
Connect to the included IR Emitter and attach the emitter bud to any projector IR window.
III. Additional Projector Information
There are settings on the Sharp PG-M20x projector that will affect how the SmartPanel will work. In order
to receive the best performance, set the following options to OFF in the projectors menu screens.
Press the MENU button either using the SmartPanel hidden functions or the Sharp remote control. Then
change the following settings.
1. In the Options menu screen turn Auto Power Off to OFF
2. In the Options menu screen turn the Power Save to OFF
3. In the Options menu screen turn the Auto Search to OFF
Projector Driver Application Note
Sharp PG-M20x
Revision A
DR-SHP20 – 9/17/03 SP Controls reserves the right to modify specifications without notice at any time.
This document describes the SmartPanel Projector Driver for the Sharp PG-M20X projector. For more
information on configuring and using the Panel see the SmartPanel Configuration and Installation
Manual.
I. PROJECTOR CONTROL
A. Volume and Power Control
Volume control on the Sharp is relative.
B. Input Selection Mapping
The following table specifies the factory-preset input mapping for this Driver. The Configuration Utility
can be used to customize these settings your installation.
Selection 1: DVI
Selection 2: S-VIDEO
Selection 3: VIDEO
Selection 4: VIDEO
Input choices available for the Sharp with this
Driver are DVI, S-VIDEO, and VIDEO
C. Hidden Function Mapping
The following table specifies the factory preset hidden function mapping for this Driver. The
Configuration Utility can be used to customize these settings your installation.
Selection 1: ENTER
Selection 2: UNDO
Selection 3: ADJUST LEFT
Selection 4: ADJUST RIGHT
Off: MENU
Volume Up: ADJUST UP
Volume Down: ADJUST DOWN
Hidden functions names are based on the Sharp
remote and controls on top of the projector. Adjust controls navigate through onscreen menus. Hidden
functions are accessed by pressing the indicated key while the holding the On key down.
The hidden functions available for the Sharp with this Driver are as follows:
MENU
ADJUST LEFT
ADJUST RIGHT
ADJUST UP
ADJUST DOWN
ENTER
ENLARGE +
ENLARGE –
FREEZE
AV MUTE
UNDO
Projector
Ready
Warm-up
OFF
ON
Volume
DVI
S-VDEO VIDEO VIDEO
Projector
Ready
Warm-up
OFF
ON
Volume
ADJUST
UP
ADJUST
DOWN
MENU
ENTER
UNDO ADJUST
LEFT ADJUST
RIGHT
SmartPanel Projector Driver Application Note Sharp PG-M20x
D. Relays
The following table specifies the factory preset
settings for the low-current relays found on the rear
of the SmartPanel. The Configuration Utility can
be used to customize these settings your installation.
Relay 1 ON Maintained
Relay 2 ON Momentary
Relay 3 OFF Momentary
Selection Momentary; not Binary
E. Other Presets
The following table specifies other default factory settings for this Driver that affect is control of the
Projector.
Power Status Feedback Method Sensor (see note 1)
Control Wiring Option IR-Emitter (see note 2)
Control for the Sharp with this Driver is via both RS-232 and IR/Wired Remote. We recommend wiring for
the Wired Remote but the included IR emitter may also be used.
The following table specifies settings for the Panel’s configurable timers. For more information on the
inactivity shutdown feature and the lockout timer see the SmartPanel Configuration and Installation
Manual
Lockout Timer 100 seconds (see note 3)
Inactivity Shutdown Disabled
RELAYS
PWR
ON
MAINT.
PWR
ON
MOM.
PWR
OFF
MOM.
1A
1B
3A
3B
2A
2B
4A
4B
6A
6B
5A
5B
7A
7B
SELECTION
(EXT. SWITCHER CTRL)
4321
500mA MAX. CURRENT
SmartPanel Projector Driver Application Note Sharp PG-M20x
II. CONTROL WIRING
PROJECTOR CONTROL
RS232 IR/SERIAL
RX
GND
CTS
RTS
TX
+12V
GND
IR/SER
SENSE
IR Emitter
(included with Panel)
1/8" Mini
Female
IR Emitter to
any IR window
This section specifies how IR-Emitter should be wired to
the Sharp projector.
A. The IR Emitter should be connected to the one of the
Sharp IR windows as follows:
1. Wire the Panel to a female 1/8” Mini as show; wire
IR/SER to tip and GND to ring. Splicing and direct
wiring to the IR Emitter is not recommended as it
makes removal of the Panel for service more difficult.
2. Connect the included IR Emitter to the female mini.
3. Affix the IR Emitter to one of the IR windows on the
projector.
Note that the emitter glows red when IR is emitted so wiring
can be verified.
Additional Projector Settings:
There are settings on the Sharp PG-M20x projector that will
affect how the SmartPanel will work. In order to receive the
best performance, set the following options to OFF in the
projectors menu screens.
Press the MENU button either using the SmartPanel hidden
functions or the Sharp remote control. Then change the
following settings.
1. In the Options menu screen turn Auto Power Off to OFF
2. In the Options menu screen turn the Power Save to OFF
3. In the Options menu screen turn the Auto Search to OFF
SmartPanel Projector Driver Application Note Sharp PG-M20x
III. TROUBLESHOOTING
Addition tips can be found in the SmartPanel Configuration and Installation Manual.
The Panel does not do anything at all.
When power is applied to the Panel it should run through a brief power on self-test, during which all of
the Panel lights will turn on and off in sequence. If you do not see this self test, make sure power is
connected correctly and that polarity is correct.
The Panel keeps turning itself off even though the projector is on.
The Panel turns itself off when power polling indicates that the projector is off. Check to make sure
the RS-232 connection is correctly wired (it is extremely unlikely other control would work, and power
polling not).
When I try to turn the projector on, the warming indicator (red LED) blink.
The projector is in the default configured lockout state, and the Panel is waiting for its internal lockout
timer to expire. This feature protects the projector’s bulb. Be sure to let your client know about this
behavior.
IV. TECHNICAL NOTES
1. By default, projector power is verified by polling every few seconds via the RS-232 port. Power
polling can be suspended by depressing and holding the On key; polling will be restored when the
key is released. Should the Sharp power off, the Panel will usually detect this condition and power
off within twenty seconds. Should the Sharp power on, the Panel will usually detecting this condition
and power on within ten seconds.
2. The Sharp is controlled via both IR/Wired Remote and RS-232. We recommend Wired Remote
control as it is generally more robust. However, use of the Wired Remote will prevent use of the
Sharp’s remote control. A complete discussion of the relative advantages of IR vs. Wired Remote
can be found in the SmartPanel Configuration and Installation Manual.
3. The lockout timer specifies the amount of time allowed between sending POWER OFF and POWER
ON to the projector (the delay allows the projector bulb to cool before re-powering). This delay can
be configured using the Configuration Utility; however, adjusting the lockout timer delay is
strongly discouraged as rapid re-powering causes undue wear on the projector’s bulb. Also, the
Sharp will not allow power to be restored before a minimum delay has expired. Therefore,
disabling the lockout delay will cause potentially confusing Panel behavior.
V. REVISION HISTORY
1. Revision A (September 2003) Initial Release.
Inhaltsverzeichnis
Andere Sharp Projektor Handbücher
Sharp
Sharp XG-NV5XU Bedienungsanleitung
Sharp
Sharp XG-NV4SU Bedienungsanleitung
Sharp
Sharp XG-NV4SE Bedienungsanleitung
Sharp
Sharp XG-E690UB Operation Bedienungsanleitung
Sharp
Sharp XG-NV3XU Operation Bedienungsanleitung
Sharp
Sharp PG-C20XE - Notevision SXGA LCD Projector Bedienungsanleitung
Sharp
Sharp XV-Z30000 Operation Benutzerhandbuch
Sharp
Sharp DT-400 Bedienungsanleitung
Sharp
Sharp XG-MB50X Bedienungsanleitung
Sharp
Sharp Notevision XG-C335X Benutzerhandbuch
Sharp
Sharp PG-D4010X - XGA DLP Projector Bedienungsanleitung
Sharp
Sharp XG-MB65X Bedienungsanleitung
Sharp
Sharp Notevision XG-C335X Bedienungsanleitung
Sharp
Sharp XG-MB65X Bedienungsanleitung
Sharp
Sharp Notevision PG-M15X Bedienungsanleitung
Sharp
Sharp PGF325W - WXGA DLP Projector Benutzerhandbuch
Sharp
Sharp XG - NV6XU Bedienungsanleitung
Sharp
Sharp PG-D120U - Pro - LCD Projector Bedienungsanleitung
Sharp
Sharp Notevision PG-D2510X Bedienungsanleitung
Sharp
Sharp Notevision PG-M17X Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
