Sharp XG-C45XU Bedienungsanleitung
Quick Start Reference Sheet
Sharp XG-C45XU
Revision A
DR-SHP22 - 12/18/03 SP Controls reserves the right to modify specifications without notice at any time.
NOTE: This one-page document is intended only as a quick reference for installation – please read
the SP Controls Application Note for a complete description of this projector driver prior to installation.
I. Driver Features
1. Input Selection Mapping
Selection 1: VIDEO
Selection 2: S-VIDEO
Selection 3: RGB 1
Selection 4: RGB 2
2. Hidden Function Mapping (Default Configuration)
Using the ON button as a shift key, press the following buttons to access the specified projector features.
Selection 1: BLANK SCREEN
Selection 2: ENTER
Selection 3: ADJ LEFT
Selection 4: ADJ RIGHT
Off: MENU
Volume Up: ADJ UP
Volume Down: ADJ DOWN
3. Other Driver Features
Power Status Feedback Method RS-232 Power Polling
Control Wiring: RS-232 and IR-Emitter
II. Wiring Specifications
NOTE: For a wiring diagram, please see the SP Controls Application Note.
1. RS-232:
Wire the Panel RS-232 port to a female DB9 as follows:
TX to 2
RX to 3
GND to 5
Connect this female DB9 to the included Sharp intermediate cable (labeled RS-232C) and connect
the mini-DIN end of the adapter to the projector port labeled CONTROL.
2. Infrared Emitter:
Wire the Panel IR/Serial port to a female 1/8" Mini as follows:
IR/SER to tip
GND to ring
Connect to the included IR Emitter and attach the emitter bud to any projector IR window.
III. Additional Projector Information
The C45XU can be configured with an Economy Mode, which determines whether or not the projector
shuts itself off in the absence of an input signal.
When installing the C45XU, you should set the Economy Mode to OFF. This disables the Sharp’s
Automatic Power Shutoff feature.
Economy Mode is set via on screen menus, Options: Economy Mode. Access the onscreen menus with
either the SmartPanel’s hidden functions, or the Sharp’s remote control.
Projector Driver Application Note
Sharp XG-C45XU
Revision A
DR-SHP22 - 12/18/03 SP Controls reserves the right to modify specifications without notice at any time.
This document describes the SmartPanel Projector Driver for the Sharp XG-C45XU projector. For
information on configuring and using the Panel see the SmartPanel Configuration and Installation Guide.
Please read the SPECIAL CONTROL NOTE in the Control Wiring section of this document before
attempting control of the projector. This note describes how the Sharp’s Economy Mode impacts the
projector’s behavior.
I. PROJECTOR CONTROL
A. Volume and Power Control
Volume control on the Sharp is absolute. Absolute volume control is also possible with SP Controls’
option Audio Follow Video Preamplifer (SP3-AFVP+).
B. Input Selection Mapping
The following table specifies the factory-preset input mapping for this Driver. The Configuration Utility
can be used to customize these settings your installation.
Selection 1: VIDEO
Selection 2: S-VIDEO
Selection 3: RGB 1
Selection 4: RGB 2
Input choices available for the Sharp with this
Driver are VIDEO, S-VIDEO, RGB 1, and RGB 2.
C. Hidden Function Mapping
The following table specifies the factory preset hidden function mapping for this Driver. The
Configuration Utility can be used to customize these settings your installation.
Selection 1: BLACK SCREEN
Selection 2: ENTER
Selection 3: ADJUST LEFT
Selection 4: ADJUST RIGHT
Off: MENU
Volume Up: ADJUST UP
Volume Down: ADJUST DOWN
Hidden functions names are based on the Sharp remote and controls on top of the projector. Hidden
functions are accessed by pressing the indicated key while the holding the On key down.
ADJUST controls, ENTER and UNDO navigate through onscreen menus. UNDO is a “return to previous
menu” or “back” command. MENU can also be used as UNDO. The area zoomed with the ENLARGE
function can be moved using the ADJUST keys.
BLACK SCREEN is a toggle.
Projector
Ready
Warm-up
OFF
ON
Volume
VIDEO
S-VIDEO RGB 1 RGB 2
Projector
Ready
Warm-up
OFF
ON
Volume
ADJUST
UP
ADJUST
DOWN
MENU
BLACK
SCREEN
ENTER ADJUST
LEFT ADJUST
RIGHT
SmartPanel Projector Driver Application Note Sharp XG-C45XU
AUTO SYNC only works when an RGB input is selected.
The hidden functions available for the Sharp with this Driver are as follows:
MENU
ADJUST LEFT
ADJUST RIGHT
ADJUST UP
ADJUST DOWN
ENTER
UNDO
BLACK SCREEN
AUTO SYNC
TOOLS
KEYSTONE
FREEZE
ENLARGE
RESIZE
NOISE FILTER ON
NOISE FILTER OFF
D. Relays
The following table specifies the factory preset
settings for the low-current relays found on the rear
of the SmartPanel. The Configuration Utility can
be used to customize these settings your installation.
Relay 1 ON Maintained
Relay 2 ON Momentary
Relay 3 OFF Momentary
Selection Momentary; not Binary
E. Other Presets
The following table specifies other default factory settings for this Driver that affect is control of the
Projector.
Power Status Feedback Method Power Polling (see note 1)
Control Wiring RS-232 and Infrared Emitter
(see note 2)
Control for the Sharp with this Driver is via RS-232 and Infrared Emitter. The XG-C45XU does not have a
Wired Remote port.
The following table specifies settings for the Panel’s configurable timers. For more information on the
inactivity shutdown feature and the lockout timer see the SmartPanel Configuration and Installation
Guide.
Lockout Timer 70 seconds (see note 3)
Inactivity Shutdown Disabled
RELAYS
PWR
ON
MAINT.
PWR
ON
MOM.
PWR
OFF
MOM.
1A
1B
3A
3B
2A
2B
4A
4B
6A
6B
5A
5B
7A
7B
SELECTION
(EXT. SWITCHER CTRL)
4321
500mA MAX. CURRENT
SmartPanel Projector Driver Application Note Sharp XG-C45XU
II. CONTROL WIRING
PROJECTOR CONTROL
RS232 IR/SERIAL
RX
GND
CTS
RTS
TX
+12V
GND
IR/SER
SENSE
Female DB9
RS-232 to
RS-232C
1/8" Mini
Female
IR Emitter to
any window
Sharp Male DB9 to Male MiniDIN adaptor
(included with Sharp projector, labeled RS-232C)
54321
9876
54321
IR Emitter
(included with Panel)
TX to 2
RX to 3
GND to 5
This section specifies how RS-232 and the Infrared Emitter
should be wired to the Sharp projector.
A. RS-232 should be connected to the Sharp control port
labeled RS-232C. Connection should be as follows:
1. Wire the Panel to a female DB9 as follows:
TX to 2
RX to 3
GND to 5
2. Connect this female DB9 to the Sharp’s custom DB9 to
mini-DIN adapter cable. This cable is included with the
Sharp and is labeled RS-232C.
3. Connect the Sharp custom cable to the projector port
labeled RS-232C IOIOI.
B. Infrared should be wired to any Sharp infrared port.
Connection should be as follows:
1. Wire the Panel to a female 1/8" Mini as shown; wire
IR/SER to tip and GND to ring. Direct wiring to the IR
Emitter is not recommended as it makes removal of the
Panel for service more difficult.
2. Attach to any projector IR port using the Panel’s IR
Emitter (included with the Panel).
Note that the emitter glows red when IR is emitted so wiring
can be verified.
SPECIAL CONTROL NOTE
Read before attempting to control the projector
The C45XU can be configured with an Economy Mode,
which determines whether or not the projector shuts itself
off in the absence of an input signal.
When installing the C45XU, you should set the Economy
Mode to OFF. This disables the Sharp’s Automatic
Power Shutoff feature.
Economy Mode is set via on screen menus, Options:
Economy Mode. Access the onscreen menus with either
the SmartPanel’s hidden functions, or the Sharp’s remote
control.
Questions should be directed to SP Controls technical
SmartPanel Projector Driver Application Note Sharp XG-C45XU
III. TROUBLESHOOTING
Additional tips can be found in the SmartPanel Configuration and Installation Guide.
The Projector keeps turning itself off!
Verify that the C45XU’s Economy Mode is set to OFF as explained in the Special Note in the Control
Wiring section of this document. If the Economy Mode is on, the projector will shut itself off after
fifteen minutes. If power polling or a third party power current sensor is being used (e.g., AMX-PCS),
the Panel will automatically shut itself off also. If not, the Panel will remain on and you will have to
power the Panel off with the Off button and wait until the lockout timer expires before you can re-
power the projector.
The Panel does not do anything at all.
When power is applied to the Panel it should run through a brief power on self-test, during which all of
the Panel lights will turn on and off in sequence. If you do not see this self test, make sure power is
connected correctly and that polarity is correct.
The Panel keeps turning itself off even though the projector is on.
The Panel turns itself off when power status feedback indicates that the projector is off. If a third
party power current sensor is being used, check to make sure that it is correctly wired, and that it is
correctly calibrated according to the manufacturer’s instructions. If not, make sure that the Panel is
configured with None or Power Polling under power status feedback in the Configuration Utility’s
Wiring Options tab.
IV. TECHNICAL NOTES
1. By default, projector power is verified by polling every few seconds via the RS-232 port. Power
polling can be suspended by depressing and holding the On key; polling will be restored when the
key is released. Should the Sharp power off, the Panel will usually detect this condition and power
off within twenty seconds. Should the Sharp power on, the Panel will usually detecting this condition
and power on within ten seconds.
2. The Sharp is controlled via RS-232 and Infrared with this Driver. Wired remote can not be wired as
the Sharp does not have a wired remote port. A discussion of the advantages of Wired Remote
versus IR can be found in the SmartPanel Configuration and Installation Guide.
3. The lockout timer specifies the amount of time allowed between sending POWER OFF and POWER
ON to the projector (the delay allows the projector bulb to cool before re-powering). This delay can
be configured using the Configuration Utility; however, adjusting the lockout timer delay is
strongly discouraged as rapid re-powering causes undue wear on the projector’s bulb. Also, the
Sharp will not allow power to be restored before a minimum delay has expired. Therefore, disabling
the lockout delay will cause potentially confusing Panel behavior.
V. REVISION HISTORY
1. Revision A (December, 2003) Original release.
Inhaltsverzeichnis
Andere Sharp Projektor Handbücher
Sharp
Sharp Notevision PG-M15X Bedienungsanleitung
Sharp
Sharp PG-F312X - Notevision XGA DLP Projector Bedienungsanleitung
Sharp
Sharp PG-F320W - Notevision WXGA DLP Projector Bedienungsanleitung
Sharp
Sharp Notevision XR-20XA Bedienungsanleitung
Sharp
Sharp PG-LW3500 Bedienungsanleitung
Sharp
Sharp Notevision PG-D3550W Bedienungsanleitung
Sharp
Sharp XR-30S - SVGA DLP Projector Bedienungsanleitung
Sharp
Sharp XG-P20XU Bedienungsanleitung
Sharp
Sharp XV-Z10000 Bedienungsanleitung
Sharp
Sharp Notevision PG-M17X Bedienungsanleitung
Sharp
Sharp Notevision XG-C40XU Bedienungsanleitung
Sharp
Sharp PG-D3750W - WXGA DLP Projector 720p Bedienungsanleitung
Sharp
Sharp XV-Z10000UL Bedienungsanleitung
Sharp
Sharp XG-V10XU - Conference Series XGA LCD... Bedienungsanleitung
Sharp
Sharp XV-Z12000 - Vision - DLP Projector Bedienungsanleitung
Sharp
Sharp Notevision PG-M20X Bedienungsanleitung
Sharp
Sharp XV-Z90E Bedienungsanleitung
Sharp
Sharp Notevision PG-D40W3D Bedienungsanleitung
Sharp
Sharp XG-NV2SB Bedienungsanleitung
Sharp
Sharp XV-Z1E Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
