Sharp XG-PH50X - XGA DLP Projector Bedienungsanleitung
Quick Start Reference Sheet
Sharp XG-PH50X
Revision B
8/10/05 SP Controls reserves the right to modify specifications without notice at any time.
NOTE: This document is intended only as a quick reference for installation – please read the following
SP Controls Application Note for a complete description of this projector driver prior to installation.
I. Driver Features
1. Input Selection Mapping
Selection 1: RGB 1 (HD15)
Selection 2: RGB 2 (BNC)
Selection 3: VIDEO 1 (RCA)
Selection 4: VIDEO 2 (S-VID)
2. Hidden Function Mapping
Selection 1: AUTO SYNC
Selection 2: ENTER
Selection 3: ADJUST LEFT
Selection 4: ADJUST RIGHT
Off: MENU
Volume Up: ADJUST UP
Volume Down: ADJUST DOWN
3. Other Driver Features
Power Status Feedback Method RS-232 Power Polling
Control Wiring Option RS-232 and Wired Remote or IR Emitter
Note: when the Panel is wired to the projector Wired Remote port, the projector remote control will no
longer function.
II. Wiring Specifications
NOTE: For a wiring diagram, please see the SP Controls Application Note for the Sharp XG-PH50X
1. RS-232:
Wire the Panel RS-232 port to a female DB9 as follows:
RX to 2
TX to 3
GND to 5
Connect this female DB9 to the projector port labeled RS-232C.
2. Wired Remote:
Wire the Panel IR/Serial port to a female 1/8" Mini as follows:
IR/SER to Tip
GND to ring
Attach to the projector port labeled Wired Remote using a male 1/8” mini to male 1/8” mini.
III. Additional Projector Information
1. The XG-PH50X requires the correct menu settings for use with the SmartPanel:
•Configure to BAUD 9600 (default) in the second OPTIONS menu
•Configure to LAN/RS-232C ENABLED in the second OPTIONS menu
2. SmartPanel customers have reported intermittent control failures using the SmartPanel with the Sharp
XG-PH50X, though as of the writing of this Application Note SP Controls believes this issue has been
resolved. Please read Section V. Special Control Note in the Application Note for more information, or
contact SP Controls Technical Support
Projector Driver Application Note
Sharp XG-PH50X
Revision B
8/10/05 SP Controls reserves the right to modify specifications without notice at any time.
This document describes the SmartPanel Projector Driver for the Sharp XG-PH50X projector. For
information on configuring and using the Panel see the SmartPanel Configuration and Installation Guide.
ATTENTION: Please read Section V. Special Control Note before attempting to control this projector.
NOTE: The XG-PH50X requires the correct menu settings for use with the SmartPanel:
•Configure to BAUD 9600 (default) in the second OPTIONS menu
•Configure to LAN/RS-232C ENABLED (default) in the second OPTIONS menu
I. PROJECTOR CONTROL
A. Volume and Power Control
Volume control on the Sharp is absolute. Absolute volume control is also possible with SP Controls’
option Audio Follow Video Preamplifer.
B. Input Selection Mapping
The following table specifies the factory preset input mapping for this Driver. The Configuration Utility
can be used to customize these settings your installation.
Selection 1: RGB 1 (HD15)
Selection 2: RGB 2 (BNC)
Selection 3: VIDEO 1 (RCA)
Selection 4: VIDEO 2 (S-VID)
Input choices available for the Sharp with this
Driver are RGB 1 (HD15), RGB 2 (BNC), RGB 3
(DVI), VIDEO 1 (RCA), and VIDEO 2 (S-VID).
C. Hidden Function Mapping
The following table specifies the factory preset hidden function mapping for this Driver. The
Configuration Utility can be used to customize these settings your installation.
Selection 1: AUTO SYNC
Selection 2: ENTER
Selection 3: ADJUST LEFT
Selection 4: ADJUST RIGHT
Off: MENU
Volume Up: ADJUST UP
Volume Down: ADJUST DOWN
Hidden functions names are based on the Sharp remote and controls on top of the projector.
Hidden functions names are based on the Sharp remote, manual, and controls on top of the projector.
ADJUST controls, ENTER and UNDO navigate through onscreen menus. UNDO is a “return to previous
menu” or “back” command. MENU can also be used as UNDO.
Hidden functions are accessed by pressing the indicated key while the holding the On key down.
Projector
Ready
Warm-up
OFF
ON
Volume
RGB 1 RGB 2 VIDEO 1 VIDEO 2
Projector
Ready
Warm-up
OFF
ON
Volume
ADJUST
UP
ADJUST
DOWN
MENU
AUTO SYNC
ENTER
ADJUST
LEFT
ADJUST
RIGHT
SmartPanel Projector Driver Application Note Sharp XG-PH50X
The hidden functions available for the Sharp with this Driver are as follows:
MENU
ADJUST LEFT
ADJUST RIGHT
ADJUST UP
ADJUST DOWN
ENTER
UNDO
BLACK SCREEN
LENS SELECT
AUTO SYNC
ZOOM UP
ZOOM DOWN
FOCUS UP
FOCUS DOWN
ENLARGE UP
ENLARGE DOWN
KEYSTONE
RESIZE
FREEZE
MUTE
D. Relays
The following table specifies the factory preset
settings for the low-current relays found on the rear
of the SmartPanel. The Configuration Utility can
be used to customize these settings your installation.
Relay 1 ON Maintained
Relay 2 ON Momentary
Relay 3 OFF Momentary
Selection Momentary; not Binary
E. Other Presets
The following table specifies other default factory settings for this Driver that affect is control of the
Projector.
Power Status Feedback Method RS-232 Power Polling (see note 1)
Control Wiring Option Wired Remote or IR Emitter (see note 2)
Control for the Sharp with this Driver is via RS-232 and Wired Remote. An IR Emitter can alternately be
used.
NOTE: When Wired Remote is connected to the Sharp projector, the Sharp will not respond to its remote
control.
The following table specifies settings for the Panel’s configurable timers. For more information on the
inactivity shutdown feature and the lockout timer see the SmartPanel Configuration and Installation
Guide.
Lockout Timer 66 seconds (see note 3)
Inactivity Shutdown Disabled
RELAYS
PWR
ON
MAINT.
PWR
ON
MOM.
PWR
OFF
MOM.
1A
1B
3A
3B
2A
2B
4A
4B
6A
6B
5A
5B
7A
7B
SELECTION
(EXT. SWITCHER CTRL)
4321
500mA MAX. CURRENT
SmartPanel Projector Driver Application Note Sharp XG-PH50X
II. CONTROL WIRING
PROJECTOR CONTROL
RS232 IR/SERIAL
RX
GND
CTS
RTS
TX
+12V
GND
IR/SER
SENSE
Female DB9
RS-232 to
RS-232C
1/8" Mini
Female
Wired Remote to
Wired Remote
54321
9876
5432 1
Jumper
8 to 7
1/8" Male Mini to 1/8" Male Mini
(not included)
This section specifies how RS-232 and Wired Remote
should be wired to the Sharp projector.
A. RS-232 should be connected to the Sharp control port
labeled RS-232C. Connection should be as follows:
1. Wire the Panel to a female DB9 as follows:
RX to 2
TX to 3
GND to 5
2. Connect this female DB9 to the projector port labeled
RS-232C.
B. The Wired Remote should be connected to the Sharp
port labeled Wired Remote.
Connection should be as follows:
1. Wire the Panel to a female 1/8" Mini as shown; wire
IR/SER to tip and GND to ring. Direct wiring to male
1/8” is not recommended as it makes removal of the
Panel for service more difficult.
2. Attach to the projector port labeled Wired Remote
using a male 1/8” mini to male 1/8” mini (not included).
3. Alternately, replace the male to male cable with the
included the IR Emitter and attach it to one of the IR
windows on the projector. The emitter glows red when
IR is emitted so wiring can be verified.
NOTE: when the Panel is wired to the projector Wired
Remote port, the projector remote control will no longer
function.
ATTENTION: SP Controls strongly recommends wiring
IR in addition to wiring RS-232 in case the Panel must be
configured for IR-only control in the future. See Section V.
Special Control Note below for more information.
SmartPanel Projector Driver Application Note Sharp XG-PH50X
III. TROUBLESHOOTING
Additional tips can be found in the SmartPanel Configuration and Installation Guide.
The Panel is not controlling the projector at all, and it turns off after about one minute of use.
Check to make sure the RS-232 connection is correctly wired – this is the single most common cause
of control failure in SmartPanel installations. If the SmartPanel does not receive projector feedback
that the projector is on, it will shut itself off using the RS-232 power polling feature (see note 1).
Verify that the XG-PH50X is configured with the following settings in its onscreen menus:
•Configure to BAUD 9600 (default) in the second OPTIONS menu
•Configure to LAN/RS-232C ENABLED in the second OPTIONS menu
In addition, this projector may be vulnerable to periodic control failures for unknown reasons – please
see Section V. Special Control Note below for more information.
The Panel does not do anything at all.
When power is applied to the Panel it should run through a brief power on self-test, during which all of
the Panel lights will turn on and off in sequence. If you do not see this self-test, make sure power is
connected correctly and that polarity is correct.
The Panel has only partial control over the Sharp.
Verify that both RS-232 and the wired remote are correctly wired. The most common error is reversal
of RX and TX for RS232, and polarity reversal of the wired remote. Note that the Sharp is controlled
using both Wired Remote and RS-232. If a subset of functionality appears to be working, verify that
both types of control wiring are correctly wired.
IV. TECHNICAL NOTES
1. By default, projector power is verified by polling every few seconds via the RS-232 port. Power
polling can be suspended by depressing and holding the On key; polling will be restored when the
key is released. Should the Sharp power off, the Panel will usually detect this condition and power
off within twenty seconds. Should the Sharp power on, the Panel will usually detecting this condition
and power on within ten seconds.
2. The Sharp is controlled via RS-232 and wired remote. The Sharp can alternately be controlled with
RS-232 and IR emitter. A discussion of the advantages of Wired Remote versus IR can be found in
the SmartPanel Configuration and Installation Guide.
3. The lockout timer specifies the amount of time allowed between sending POWER OFF and POWER
ON to the projector (the delay allows the projector bulb to cool before re-powering). This delay can
be configured using the Configuration Utility; however, adjusting the lockout timer delay is
strongly discouraged as rapid re-powering causes undue wear on the projector’s bulb. Also, the
Sharp will not allow power to be restored before a minimum delay has expired. Therefore, disabling
the lockout delay will cause potentially confusing Panel behavior.
SmartPanel Projector Driver Application Note Sharp XG-PH50X
V. SPECIAL CONTROL NOTE – IR-Only Driver Available
SP Controls has received reports of an intermittent control failure from customers using the Sharp XG-
PH50X projector with the SmartPanel. As of the writing of this Application Note, all reported failures
occurred using the Sharp XG-P25XU SmartPanel driver to control the XG-PH50X. Control failures have
never been reported using this driver.
SP Controls attempted to reproduce control failures through intensive testing, but we were able to create
an abnormal projector condition only once. We observed, seemingly at random, the projector fan activate
normally in response to a Panel ON command, but the lamp did not illuminate. The projector did not
respond to any control commands until it was unplugged and replugged-in. We were unable to replicate
this power on failure after carefully reproducing the same conditions many times.
There are significant differences between the XG-P25XU driver and the XG-PH50X driver which may well
prevent such a failure from occurring, but at this time the problem state is not well understood. If you
should experience a control failure, please contact SP Controls Technical Support right away at toll
free (877) 367-8444 ext. 302.
If this issue is of concern to you, SP Controls has written a Revision A of this driver which controls the
projector entirely through Wired Remote control. Such an installation should be completely immune to
control failure. This driver is available upon request from SP Controls. You may call the number above or
Note: When the SmartPanel is wired to the projector’s WIRED REMOTE port, it will no longer respond
to its remote control.
VI. REVISION HISTORY
1. Revision A (August, 2005) Original release – IR-only version. BT
2. Revision B (August, 2005) Original release – RS-232/IR version. BT
Andere Handbücher für XG-PH50X - XGA DLP Projector
3
Inhaltsverzeichnis
Andere Sharp Projektor Handbücher
Sharp
Sharp Notevision PG-C20XA Bedienungsanleitung
Sharp
Sharp XG-MB50X Bedienungsanleitung
Sharp
Sharp XV-Z200U Bedienungsanleitung
Sharp
Sharp XG-C45XU Bedienungsanleitung
Sharp
Sharp PG-A10X - Notevision XGA LCD Projector Bedienungsanleitung
Sharp
Sharp PG-D4010X - XGA DLP Projector Bedienungsanleitung
Sharp
Sharp Notevision PG-D2870W Bedienungsanleitung
Sharp
Sharp XV-Z90 Bedienungsanleitung
Sharp
Sharp XR-32X - Notevision XGA DLP Projector Bedienungsanleitung
Sharp
Sharp PG-LW2000 Bedienungsanleitung
Sharp
Sharp NoteVision PG-LX2000 Bedienungsanleitung
Sharp
Sharp XG-F260X Bedienungsanleitung
Sharp
Sharp Notevision PG-C30XU Bedienungsanleitung
Sharp
Sharp PG-C30XE - Notevision XGA LCD Projector Bedienungsanleitung
Sharp
Sharp PG-C20X Bedienungsanleitung
Sharp
Sharp XV-Z1U Bedienungsanleitung
Sharp
Sharp Notevision XG-C455W Bedienungsanleitung
Sharp
Sharp XG - P10XU Bedienungsanleitung
Sharp
Sharp XG-SV1E Bedienungsanleitung
Sharp
Sharp Notevision XG-NV7XU Montageanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
