Sharp HTSB200 - Sound Bar Speaker Bedienungsanleitung

HT-SB200

SERVICE MANUAL

No. S1902HTSB200W

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

PRECAUTIONS FOR USING LEAD-FREE SOLDER

CHAPTER 1. GENERAL DESCRIPTION

[1]

AC Power Supply Cord And AC Plug Adaptor

.. 1-1

[2] Specifications ................................................ 1-1

[3] Name Of Parts ............................................... 1-2

CHAPTER 2. ADJUSTMENTS

[1] Test Mode....................................................... 2-1

CHAPTER 3. MECHANISM BLOCKS

[1] Disassembly................................................... 3-1

CHAPTER 4. DIAGRAMS

[1] Block Diagrams.............................................. 4-1

CHAPTER 5. CIRCUIT DESCRIPTION

[1] Voltage ........................................................... 5-1

CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS

LAYOUT

[1] Notes On Schematic Diagram .......................6-1

[2] Types Of Transistor And LED........................6-1

[3] Schematic Diagram .......................................6-2

[4] Chart Of Connecting Wires............................6-8

[5] Wiring Side Of PWB ....................................6-10

CHAPTER 7. OTHERS

[1] Function Table Of IC......................................7-1

PARTS GUIDE

SOUND BAR SYSTEM

HT-SB200

MODEL

CONTENTS

is a trademark of SRS Labs, Inc.

WOW HD technology is incorporated under license

from SRS Labs, Inc.

SHARP CORPORATION

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with

specified ones for maintaining the safety and performance of the set.

• In the interests of user-safety the set should be restored

to its original condition and only parts identical to those

specified be used.

[ ASIA, EX ]

HT-SB200

– i –

PRECAUTIONS FOR USING LEAD-FREE SOLDER

1. Employing lead-free solder

Example:

Indicates lead-free solder of tin, silver and copper.

Lead-free wire solder for servicing

Ref No. Description

Parts No.

"MAIN, POWER, AMPLIFIER PWB" of this model employs lead-free solder. The LF symbol indicates lead-free

solder, and is attached on the PWB and service manuals. The alphabetical character following LF shows the type

of lead-free solder.

Using lead-free wire solder

When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional

lead wire solder may cause damage or accident due to cracks.

As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend

you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering

bit, contact our service station or service branch in your area.

Soldering

As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead

solder by 40°C,and as it has poor solder wet ability, you may be apt to keep the soldering bit in contact with the

PWB for extended period of time. However, since the land may be peeled of for the maximum heat-resistance

temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady

soldering condition.

Lead-free solder contains more tin, and the end of the soldering bit may be easily corrected. Make sure to turn

on and off the power of the bit as required. If a different type of solder stays on the tip of the soldering bit, it is

alloyed with lead-free solder. Clean the bit after every use of it.

When the tip of the soldering bit is blackened during use, file it with steel wool or fine sand paper.

Be careful when replacing parts with polarity indication on the PWB silk.

MAIN (A1) / POWER (A2) / AMPLIFIER (A3) [ For Brazil and Taiwan Only ]PWB-A 92LPWB7387MANS

PWB-A 92LPWB7388MANS MAIN (A1) / POWER (A2) / AMPLIFIER (A3) [ Except Indonesia, Brazil and Taiwan ]

PWB-A 92LPWB7394MANS MAIN (A1) / POWER (A2) / AMPLIFIER (A3) [ For Indonesia Only ]

HT-SB200

–2

CHAPTER 1: GENERAL DESCRIPTION

[2] Specifications

[1] AC Power Supply Cord And AC Plug Adaptor

CAUTION : “Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type”.

QACCEA002AW00

QACCLA002AW00

QPLGA0004AWZZ

QACCZA002AW00

QACCZA007AW00

QACCZA018AW00

General

(*) This power consumption value is obtained when in the

power stand-by mode.

Power source DC IN 12V 4A: AC/DC adaptor

(AC 100 - 240 V ~ 50/60 Hz)

Power

consumption

Power on: 10 W

Power stand-by: 0.6 W (*)

Output power Front speaker:

RMS: 12 W (6 W + 6 W) (10% T.H.D.)

RMS: 9.6 W (4.8 W + 4.8 W) (0.9% T.H.D.)

Subwoofer:

RMS: 20 W (10% T.H.D.)

RMS: 13 W (0.9% T.H.D.)

Speaker 2.1-way Speaker System

Front Speakers: 38 mm (1-1/2") Full Range

Subwoofer: 57 mm (2-1/4") Woofer (x4)

Audio output

terminals

Speakers: 12 ohms / Channel

Subwoofer: 3 ohms

(12 Ohms x 4 parallel connections)

Input terminals Analogue input (LINE 1):

RCA type x 1pair (L/R)

500 mV / 47 kohms

Analogue input (LINE 2):

Stereo mini socket Ø 3.5 mm

100 mV / 47 kohms

Dimensions Width: 800 mm (31-1/2")

Height: 96 mm (3-3/4")

Depth: 70 mm (2-3/4")

Weight 1.75 kg (3.86 lbs.)

1 – 1

HT-SB200

– 2

[3] Names Of Parts

Front panel

1. Sport Indicator

2. Standard Indicator

3. Information Display

4. Cinema/Game Indicator

5. News Indicator

6. On/Stand-by Button

7. Volume Down Button

8. Volume Up Button

9. Surround Button

10. Function Button

11. Remote Sensor

12. Left Front Speaker

13. Bass Reflex Duct

14. Subwoofers

15. Right Front Speaker

Rear Panel

1. Audio Line In 2 (3.5 mm stereo/headphone) Socket

2. Line In 1 (RCA/cinch) Sockets

3. DC Input Socket

1. Remote Control Transmitter

2. Cinema/Game Button

3. Standard Button

4. Volume Up Button

5. Subwoofer Level Down Button

6. Volume Down Button

7. Bass/Treble Button

8. On/Stand-by Button

9. Sport Button

10. News Button

11. Subwoofer Level Up Button

12. Dimmer Button

13. Mute Button

14. Line Button

15. TV Operation Buttons

Remote Control

LEFT

RIGHT

LINE IN 1LINE IN 2

123

STANDARD

SPORT

SOUND BAR SYSTEM HT-S8200

VOL.

SURROUND FUNCTION

CINEMA / GAME

NEWS

ON/STAND-BY

6 7 8 9 10 11

12 13 131514 14

451

Notes:

Some models of SHARP TV may not be operable.

SHARP TV remote will not work with HT-SB200 system.

TV Operation Buttons (Only SHARP TV):

On/Stand-by

Button

Sets the TV

power to “ON”

or “STAND-

BY”.

Input Select

Button (TV)

Press the

button to

switch the

input source.

Volume Up

and Down

Buttons

Turn up/down

the TV

volume.

Channel Up

and Down

Buttons

Switch up/

down the TV

channels.

1 – 2

HT-SB200

2 – 1

CHAPTER 2. ADJUSTMENTS

[1] Test Mode

1. Enter the Test Mode version display

While pressing down ON/STANDBY and VOL UP button, Switch ON AC supply.

Version will be display on 7 segment as below:-

b2 --> ** --> D

b2 = Model name, ( SB200 )

** = Software version no.

D = Destination code :- O (for Others), I (for Indonesia)

2. Enter the Test Mode version display

After enter Test Mode version display, Press VOL UP button.

1. All SOUND MODE LED will light ON

2. 7 segment display will light on if press button as below

3. Exit the Test Mode

While in Test Mode function, Press ON/STANDBY button to exit.

4. Error Code Description.

5. System Protection indicator

In case abnormal power detection has occurred, the unit will automatically enter to stand-by mode

ON/STANDBY LED willl be flashing as below:-

Unit enter Protect mode when irregular process occur on power supply line.

Key 7 segment

VOL DOWN 01

VOL UP 02

SURROUND 03

FUNCTION 04

Display Explanation Solution

E1 Communication error between Micom and WM877 > Unplug AC cord and turn power ON again

> Check line connected between Micom and corresponding ICE2 Communication error between Micom and NJU-26040

E3 Communication error between Micom and STA333

Flashing

OFF OFF

1 Frame

Flashing

(Repeat)

HT-SB200

3 – 1

CD-ES700/CD-ES77CD-ES700/CD-ES77Service ManualCD-ES700/CD-ES77MarketE

CHAPTER 3. MECHANISM BLOCKS

[1] Disassembly

Caution On Disassembly

Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure

excellent performance:

1. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit.

2. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing

the unit, be sure to rearrange the leads where they were before disassembling.

3. Check that all speaker cushions (refer items 212, 214, 215 and 216 on pages 6 and 7 of Parts Guide) are properly

sealed otherwise vibration noise will be very distinct at low frequency sound.

Replace the cushions if they are found damaged during servicing.

STEP REMOVAL PROCEDURE FIGURE

1 Back Cabinet Assy 1. Wall Mount Bracket…… (A1)x2 1

2. Screw…………..………. (A2)x10

3. Screw…………..………. (A3)x10

2 Amp PWB 1. Screw……….………….. (B1)x2 2

2. Connector…….……….. (B2)x1

3. Socket………………..… (B3)x2

3 Power PWB 1. Main Chassis……….…. (C1)x1 2

2. Screw………….…….…. (C2)x4

3. Screw………….…….…. (C3)x1

4. Socket………………..… (C4)x1

5. Screw………………...… (C5)x2

4 Main PWB 1. Screw………….………. (D1)x1 2

5 Woofer 1. Duct Port Holder…….… (E1)x2 3

2. Duct Port Assy………… (E2)x2 3

3. Screw………….…….…. (E3)x12 3

2. Screw………….………. (E4)x8 4

6 Speaker 1. Screw………….………. (F1)x8 4

Back Cabinet Ass’y

(A3)x4

M3x10mm

(A3)x2

M3x10mm

(A1)x1

Wall Mount Bracket

(A2)x5

M3.5x10mm

(A1)x1

Wall Mount Bracket

Front Cabinet Ass’y

(A2)x5

M3.5x10mm

(A3)x4

M3x10mm

Figure 1

HT-SB200

3 – 2

CAUTION:

TO REMOVE SPEAKER UNIT, PRESS THESE LOCKING TABS

TO RELEASE SPEAKER WIRES.

SPEAKER UNIT

LOCKING TAB

SPEAKER

WIRE

Front Cabinet Ass’y

(F1)x4

M2.6x8mm

(F1)x4

M2.6x8mm

(E4)x2

M3x10mm

(E4)x2

M3x10mm

(E4)x2

M3x10mm

(E4)x2

M3x10mm

Woofer

Speaker

(E2)x1

Duct Port Ass’y

(E2)x1

Duct Port Ass’y

(E3)x6

M3x10mm

(E3)x6

M3x10mm

(E1)x1

Duct Port Holder

(E1)x1

Duct Port Holder

Figure 2

Figure 3

Figure 4

Amplifier PWB

Power PWB

(B1)x2

Special Screw

(C3)x1

Special Screw

Front Cabinet Ass’y

(C2)x4

M3x10mm

(C1)x1

Main Chassis

(C5)x2

M3x8mm

(D1)x1

M3x8mm

(B2)x1 (B3)x1

(C4)x1

(B3)x1

Main PWB

HT-SB200

4 – 1

CHAPTER 4. DIAGRAM

[1] Block Diagram

XM601

36.864MHz

JK802 (LINE IN)

hcL

L +B2

hcR +B5

JK801 (AUDIO IN)

+B2

R 206D3B+

CETED

_LV

L6B

JK803 DZ801

2/A

5AR

OTPA

1B+

NIC

12V 4A

+B1 +B4

DZ802 DZ803

5.6B 13A

+B5

~ +B3

+B3

08D

4B+

+B2 +B1

+B3

UNSW 3.3

D604

+B6

D605

IC801

LD29080

IC803

AP2213

IC802

KIA1117F33L

IC601

WM8775

6 14

AVDD

DVDD

9IC602

NJU260409

SRS WOW

13 28 32

IC605

PST8227N

1Q601 RESET

35 POWER

27 28 30

+B1

+B2

DC_RLY

43 SYS

PROTECT

Q802

MP_12

DC_12V

XM603

32.768kHz

Q701

Q702

MICOM_UNSW

KEY

SW702-SW705

VREF

10 4846

IC604

IXA229AW

SYSTEM

MICROCOMPUTER

IC603

TJM4558CD

Q605

Q604

Q602

5 8

VDD

14 16

2 4 5

FROM AC/DC

Figure 4-1: BLOCK DIAGRAM (1/2)

HT-SB200

4 – 2

~ ~

+B2

LFRONT = 12Ω

SUBWOOFER = 3Ω

+B4

+B3

+B4

IC701

PT6965

LED701

SEVEN SEGMENT

701 LED702

4 2

REMOTE

SENSOR

W705

616 4 5

27 8

IC901

STA333BW

POWER IC

IC902

STA533W

28 30 27

22 3526

VDD

VCC

SDA

SCL

VCC

Figure 4-2: BLOCK DIAGRAM (2/2)

HT-SB200

5 – 1

CHAPTER 5.

VOLTAGE

[1] Voltage

IC601 IC602

VOLTAGE

(V)

VOLTAGE

(V)

VOLTAGE

(V)

VOLTAGE

(V)

1 2.45 15 2.45 1 3.28 17 1.63

2 1.64 16 4.91 2 3.27 18 1.64

3 1.62 17 0.00 3 3.13 19 0.90

4 0.81 18 2.45 4 3.28 20 0.00

5 1.64 19 2.45 5 0.00 21 0.00

6 0.00 20 2.45 6 3.13 22 1.62

73.28 21 2.45 7 3.28 23 0.00

8 0.00 22 2.43 8 3.28 24 0.00

9 0.00 23 2.43 9 0.00 25 3.28

10 1.52 24 2.44 10 1.55 26 1.65

11 1.50 25 2.44 11 1.54 27 3.12

12 0.00 26 2.43 12 0.00 28 0.00

13 2.43 27 2.43 13 0.00 29 0.00

14 0.00 28 2.45 14 0.80 30 0.00

15 1.64 31 0.00

16 1.64 32 0.00

IC701

VOLTAGE

(V)

VOLTAGE

(V) IC604

1 2.45 16 2.45 PIN

VOLTAGE

(V)

VOLTAGE

(V)

2 1.64 17 4.91

3 1.62 18 0.00 1 0.00 27 3.12

4 0.81 19 2.45 2 3.13 28 3.12

5 1.64 20 2.45 3 0.00 29 3.07

6 0.00 21 2.45 4 3.27 30 1.93

73.28 22 2.45 5 3.13 31 0.00

8 0.00 23 2.43 6 1.43 32 0.00

9 0.00 24 2.43 7 1.07 33 0.00

10 1.52 25 2.44 8 3.10 34 0.00

11 1.50 26 2.44 9 1.43 35 3.13

12 0.00 27 2.43 10 0.00 36 3.06

13 2.43 28 2.43 11 1.56 37 0.00

14 0.00 29 2.45 12 3.13 38 0.00

15 0.00 30 0.00 13 0.00 39 0.00

14 2.25 40 0.00

15 0.00 41 0.00

IC801 IC802 16 0.00 42 3.07

VOLTAGE

(V)

VOLTAGE

(V)

17 1.88 43 3.28

18 1.43 44 3.08

1 3.05 1 0.00 19 3.28 45 0.00

2 11.75 2 3.28 20 3.10 46 3.13

3 0.00 3 4.94 21 2.96 47 3.13

4 4.94 22 0.00 48 3.27

5 0.00 23 0.00 49 0.00

IC803 24 0.00 50 0.00

VOLTAGE

(V)

25 0.00 51 0.00

26 0.00 52 0.00

1 11.41

2 11.66

3 3.84

4 2.41

5 0.54

6 0.54

7 0.54

8 0.54

Andere Handbücher für HTSB200 - Sound Bar Speaker

Inhaltsverzeichnis

Andere Sharp Lautsprechersystem Handbücher

Sharp

Sharp HT-SBW110 Bedienungsanleitung

Sharp

Sharp HT-SB300 Bedienungsanleitung

Sharp

Sharp HT-SB32D Bedienungsanleitung

Sharp

Sharp AN-28SP2 Bedienungsanleitung

Sharp

Sharp PS-919 Bedienungsanleitung

Sharp

Sharp HT-SB110 Bedienungsanleitung

Sharp

Sharp HT-SB32D Bedienungsanleitung

Sharp

Sharp HT-SB602 Bedienungsanleitung

Sharp

Sharp HT-SB350 Bedienungsanleitung

Sharp

Sharp HT-SB147 Bedienungsanleitung

Sharp

Sharp CD-BH950 Bedienungsanleitung

Sharp

Sharp HT-SB147 Bedienungsanleitung

Sharp

Sharp HT-SBW110 Bedienungsanleitung

Sharp

Sharp XL-HF200PH(S) Bedienungsanleitung

Sharp

Sharp HT-SB300 Bedienungsanleitung

Sharp

Sharp HT-SB602 Bedienungsanleitung

Sharp

Sharp HT-SB107 Bedienungsanleitung

Sharp

Sharp HT-SB250 Bedienungsanleitung

Sharp

Sharp MD-X7H Bedienungsanleitung

Sharp

Sharp CP-USB50 Stücklistenhandbuch

Sharp

Sharp HT-SBW125 Bedienungsanleitung

Sharp

Sharp MD-MX30 MD Bedienungsanleitung

Sharp

Sharp CD-C470H Bedienungsanleitung

Sharp

Sharp androidtv 65FN2KA Bedienungsanleitung

Beliebte Lautsprechersystem Handbücher anderer Marken

JVC

JVC CA-MXK5R Bedienungsanleitung

LG NB4532B Bedienungsanleitung

JVC

JVC CA-FSH100 Bedienungsanleitung

5Core

5Core Pro Series Bedienungsanleitung

EAW

EAW MQV1394e Bedienungsanleitung

Lynx

Lynx GXR-LA10A Bedienungsanleitung

iLive

iLive ITB066B Bedienungsanleitung

RDX

RDX QuickStation 4 Bedienungsanleitung

Electro-Voice

Electro-Voice S-122 Bedienungsanleitung

Sven

Sven SPS-619 GOLD Bedienungsanleitung

Pioneer

Pioneer CS-7070 Bedienungsanleitung

EAW

EAW UB82e Bedienungsanleitung

Sondpex

Sondpex Active Speaker System and Digital Music... Bedienungsanleitung

JVC

JVC NX-PN7 Bedienungsanleitung

Marshall Amplification

Marshall Amplification AR-DM61-BT Bedienungsanleitung

Yamaha

Yamaha NX-A01 - Speaker Sys Bedienungsanleitung

SE Audiotechnik

SE Audiotechnik I-LINE Bedienungsanleitung

Gemini

Gemini WRX-843 Series Bedienungsanleitung