Sharp S7000UK Bedienungsanleitung

S7000UK

OWNER’S GUIDE

1 20800 862 0453 www.sharkclean.eu

WHEN USING YOUR SHARK®STEAM MOP,

BASIC SAFETY PRECAUTIONS SHOULD

ALWAYS BE FOLLOWED, INCLUDING THE

FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING

YOUR SHARK® MULTI-FUNCTION STEAM MOP

LITE.

DANGER OF SCALDING.

Please use caution when using the steam mop. The

steam emitted from the steam mop is very hot.

IMPORTANT:

This appliance is not intended for use by persons

with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or

instruction concerning use of the appliance by a

person responsible for their safety.

Children shall not use or play with this

appliance. Close supervision is necessary

to keep appliance out of reach of children

during use and cooling.

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

27. Store steam mop indoors in a cool, dry place.

28. To avoid circuit overload, do not operate another

appliance on the same socket (circuit) as the

steam cleaner.

29. If an extension cord is absolutely necessary, an

extension cord rated a minimum of 15 ampere,

2.08mm2(14 AWG) cord should be used. Cords

rated for less amperage may overheat. Care

should be taken to arrange cord so that it cannot

be pulled or tripped over.

30. DO NOT leave unattended when the system is

connected to a power supply or electrical outlet.

Turn off all controls before unplugging the unit.

31. DO NOT store unit with damp or wet cleaning

pad attached. Never leave the steam mop in one

spot on any surface for any period of time with

a damp or wet cleaning pad attached as this will

damage your ﬂoors.

32. Always unplug and allow the steam mop to cool

before removing the mop head or accessory nozzle.

33. Make sure that the water tank cap is secured

tightly when using the appliance.

WARNING: Your steam mop is designed

to clean hard ﬂoor surfaces that will withstand high

heat. Do not use on unsealed wood or unglazed

ceramic ﬂoors. On surfaces that have been treated

with wax or some no wax ﬂoors, the sheen may

be removed by the heat and steam action. It is

always recommended to test an isolated area of

the surface to be cleaned before proceeding. We

also recommend that you check the use and care

instructions from the ﬂoor manufacturer.

SAVE THESE

INSTRUCTIONS

14. DO NOT put any objects into openings. Do not use

with any opening that is blocked.

15. DO NOT put hands or feet under the steam mop.

Unit gets very hot.

16. Use ONLY on ﬂat, horizontal surfaces. Do not use

on walls, counters or windows.

17. DO NOT use on leather, wax polished furniture or

ﬂoors, synthetic fabrics, velvet or other delicate,

steam sensitive materials.

18. Liquid or steam must not be directed towards

equipment containing electrical components, such

as the interior of ovens.

19. DO NOT add cleaning solutions, scented

perfumes, oils or any other chemicals to the water

used in this appliance as this may damage the

unit or make it unsafe for use. If you live in a hard

water area, we recommend using distilled water in

your steam mop.

20. When in use, NEVER turn the appliance over or

on its side. NEVER DIRECT STEAM TOWARDS

PEOPLE, ANIMALS OR PLANTS.

21. NEVER LEAVE THE STEAM MOP IN ONE SPOT

ON ANY SURFACE FOR ANY PERIOD OF TIME

WHEN THE CLEANING PAD IS ATTACHED AS

THIS WILL DAMAGE YOUR FLOORS.

22. Carefully remove the cleaning pad immediately

after you have unplugged and allowed the steam

mop to cool.

23. When cleaning the steam mop, unplug the power

cord from the electrical outlet and clean with a dry

or damp cloth. Do not pour water or use alcohol,

benzene or paint thinner on the unit.

24. Extreme caution should be exercised when using

this appliance to clean stairs.

25. Never use steam mop functions without the

cleaning pads attached.

26. Keep your work area well lit.

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR INJURY:

1. Use the system only for its intended use.

2. DO NOT use outdoors.

3. DO NOT leave the appliance unattended when

plugged in. Always unplug the power cord

from the electrical outlet when not in use and

beforeservicing.

4. DO NOT allow the appliance to be used by

children. Close attention is necessary when used

near children, pets or plants.

5. Use only as described in this manual.

6 . Use only manufacturer’s recommended

accessories.

7. DO NOT use with damaged cord or plug.

8. DO NOT USE if the appliance is not working, has

been dropped, dropped into water, damaged or

left outdoors.

9. NO SERVICEABLE PARTS. Incorrect re-

assembly or repair can cause a risk of electrical

shock or injury to persons when the appliance is

used. Contact Customer Service.

10. To protect against a risk of electric shock, DO

NOT immerse the steam mop into water or any

other liquids.

11. DO NOT handle plug or steam mop with wet

hands or operate appliance without shoes.

12. DO NOT pull or carry by power cord, use power

cord as handle, close a door on the power

cord, or pull the power cord around sharp

edges or corners. Keep power cord away from

heatedsurfaces.

13. DO NOT unplug by pulling on power cord. To

unplug, grasp the plug not the power cord. Do not

use extension cords or outlets with inadequate

current carrying capacity.

3 40800 862 0453 www.sharkclean.eu

Contents

Getting Started ....................................................................................... 5

Assembling Your Steam Mop ................................................................... 6

Using Your Steam Mop ............................................................................ 7

Using Your Carpet Glider.......................................................................... 8

Using Your Handheld Steamer.................................................................. 9

Using Your Removable Handheld Steamer with Different Accessories.......... 10

Care of Your Steam Mop.......................................................................... 12

Troubleshooting Guide............................................................................. 14

Thank you for

purchasing the Shark®

Multi-Function Steam

Mop Lite.

This appliance complies with the WEEE-Directive 2002/96/EC on the disposal of electrical and electronic

equipment (WEEE).

This appliance complies with the European directives for electromagnetic compatibility (EMC) 2004/108/EC and its

revisions, as well as Low Voltage Directive (LVD) 2006/95/EC and its revisions.

This marking indicates that this product should not be disposed with other household wastes

throughout the EU. To prevent possible harm to the environment or human health from uncontrolled

waste disposal, recycle it responsibly to promote the sustainable reuse of material sources. To return

your used device, please use the return and collection systems or contact the retailer where this

product was purchased. They can take this product for environmental safe recycling.

Although the product is not provided with standby mode or off mode, it still fulﬁlls the requirements of 1275/2008/

EC - the directive for Eco-Design requirements since according to technical justiﬁcation, it is considered as

inappropriate to provide standby and off modes when connecting to mains. To reduce energy consumption be sure

to unplug the unit after use.

THIS MANUAL COVERS MODEL NUMBER:

S7000UK 11

TECHNICAL SPECIFICATIONS

Voltage: 220-240V~, 50/60Hz

Power: 1250 Watts

Water Capacity: 350 ml IPX4

Guarantee: This product is unconditionally guaranteed for one year against all defects of workmanship and

materials. This guarantee does not affect your statutory rights. If this product proves unsatisfactory please contact

our customer service department on freephone 0800 862 0453 or by e-mail ukservice@euro-pro.com.

5 60800 862 0453 www.sharkclean.eu

IMPORTANT: Always make sure the mop is

UNPLUGGED from the wall when not in use. Never

ﬁll the mop, attach the mop head, change or remove

the cleaning pad when the mop is plugged into the

wall. To prolong the life of your Shark®Multi-Function

Steam Mop Lite we recommend using distilled water.

Make sure you only add water to the tank. Chemicals

or cleaning solution may damage the appliance and

could be unsafe for you and your family.

Assembling Your Steam MopGetting Started

When assembling your steam mop there may be a little water in or around the water tank. This is because we test all

our steam mops 100% before you buy them, so you get a quality Shark® Multi-Function Steam Mop Lite.

ﬁg. 1 ﬁg. 2

aMop Handle

bCord Clip (XBTECLP03)

cWater Tank Cap

dHandheld Steamer

ePower Button

fRelease Button

gRectangle Mop Head (3072SO7000)

hAll Purpose Cleaning Pad for Rectangle Head (x2) (P159W)

iCarpet Glider (XCG7000)

jConcentrator Nozzle (3011FO2901)

kAccessory Hose (3010FO2901)

lGrout Scrubber Brush (1081SO)

mWindow Squeegee (1078SO)

nFilling Flask (1039SO)

STEAM MOP ASSEMBLY

1Insert the Mop Handle end with the “ “ facing the

front of the unit into the handheld steamer. Push the

mop handle in until you hear it click into place. (ﬁg. 1)

2Snap the mop head into the mop body by lining up

the groove on the back of the mop body with the

groove on the back of the mop head. Push until you

hear it latch into place. Press the release button to

remove or change the mop head. (ﬁg. 2)

3Place the cleaning pad on the ﬂoor with the logo

side facing up. Place the Shark®Multi-Function

Steam Mop Lite on top of the pad to attach.

7 80800 862 0453 www.sharkclean.eu

1Turn the water tank cap anticlockwise and remove

from the tank. (ﬁg. 3)

2Use the ﬁlling ﬂask and pour water into the tank. Do

not overﬁll. Replace the cap on the water tank. (ﬁg. 4)

IMPORTANT: Do not use on unsealed wood or

unglazed ceramic ﬂoors. On surfaces that have been

treated with wax or some no wax ﬂoors, the sheen

may be removed by the heat and steam action. It

is always recommended to test an isolated area

of the surface to be cleaned before proceeding.

We recommend that you check the use and care

instructions from the ﬂoor manufacturer.

IMPORTANT: Make sure you do not use the mop

without attaching a cleaning pad and adding water

to the tank ﬁrst. When you are using the mop for the

ﬁrst time, it might take longer than the normal 30

seconds to start steaming.

Using Your Steam Mop

NOTE: To prolong the life of your Steam Mop, we

recommend using distilled water.

NOTE: Sweep or vacuum your ﬂoors prior to cleaning

with your Steam Mop.

3Pull and twist the quick release cord holder to

unwrap the power cord completely. Plug into an

electrical outlet. (ﬁg. 5)

4Press the power button to turn the unit on. (ﬁg. 6)

Using Your Carpet Glider

THE CARPET GLIDER

1The Carpet Glider can be used with the Rectangular

Head to lightly steam your carpet and area rugs.

Just place the mop head with cleaning pad attached

into the glider. (ﬁg. 7)

2Move the Steam Mop back and forth across a

section of the carpet. (ﬁg. 8)

ﬁg. 7

ﬁg. 8

The Steam Mop will not clean your

carpeting or area rugs. However, it is

great for grooming and freshening.

5Clean your ﬂoors with a forward and backward

motion.

6Use the reusable, all-purpose cleaning pad to lift up

and lock away all the dirt and debris.

7When the water tank is empty, the Steam Mop will

stop producing steam. You can reﬁll the water tank

at any time as long as the mop is unplugged from

the outlet. Follow the instructions from page 4. This

applies to switching the mop head or cleaning pad

as well.

NOTE: Please wait 2-3 minutes for the Steam Mop

to cool off before switching the mop head or the

cleaning pad. Never leave the Steam Mop with a

damp/wet cleaning pad on any ﬂoor.

8When you are done, press the power button to turn

the steam mop off.

ﬁg. 5

ﬁg. 6ﬁg. 4

ﬁg. 3

9 100800 862 0453 www.sharkclean.eu

Your Shark®Multi-Function Steam Mop Lite is designed

to clean surfaces that will withstand high heat and

moisture. Do not use on unsealed wood surfaces

(especially wooden antique furniture), unglazed ceramic

tile, painted surfaces or surfaces that have been treated

with wax, oils, varnishes, or shellac. The sheen may be

removed by the heat, steam, and friction of the cleaning

tools. Lacquer and polyurethane coatings provide a hard

durable protective ﬁnish that withstands moisture, but it

is always recommended to test an isolated area of the

surface to be cleaned before proceeding.

We also recommend you check the use and care

instructions from the surface manufacturer.

When cleaning ﬁnished wood surfaces, use broad,

continuous cleaning strokes. To prevent surface damage,

avoid focusing steam or allowing the cleaning tools to sit

in one spot for any amount of time.

Using Your Handheld Steamer

1To remove the Handheld Steamer, press and hold

down the Handle Release Button while pulling out

the handle. (ﬁg. 9)

2To remove the mop head, press the mop head

release button and pull the mop head off. (ﬁg. 9)

ﬁg. 9

CAUTION: Do not press the power button while

attaching or removing the Accessory Hose.

CAUTION: Do not use the Accessory Hose without

cleaning tools attached.

1First attach the Accessory Hose to the Handheld

Steamer by snapping the Accessory Hose into the

main nozzle. (ﬁg. 10)

2Select the desired cleaning tool for use. Follow the

cleaning tool sub-assembly instructions for the

selected tool. (ﬁg. 11)

3To remove the Accessory Hose, press and hold

down the Handheld Release Buttons. Then slide out

the Accessory Hose using the grip.

ﬁg. 10

Release

Button

Using Your Removable Handheld Steamer

with the Different Accessories

ﬁg. 11

11 120800 862 0453 www.sharkclean.eu

USING THE WINDOW SQUEEGEE

Cleaning Tip: To use the window squeegee, work with

the vapor jet down using top to bottom movements. To

do this without leaving streaks, use lateral movements

from the top to the bottom of the surface.

CAUTION: Always avoid any sudden changes

in temperature to prevent breakage of cracks in

windows.

1Attach the Window Squeegee by snapping into the

handle of the Accessory Hose until it clicks into

place. (ﬁg. 14)

2Press the power button to start steaming.

3To remove the Window Squeegee, press and hold

down the Accessory release button. Then slide out

the Window Squeegee.

CAUTION: Turn the unit off before attaching or

removing the Window Squeegee.

Using Your Removable Handheld Steamer

with the Different Accessories - cont.

ﬁg. 12

USING THE CONCENTRATOR NOZZLE

Cleaning Tip: The Concentrator Nozzle creates direct

steam spray to clean and sanitise hard to reach nooks &

crannies and other places where germs may build up. Use

the Concentrator Nozzle to loosen and dislodge compact

dirt often found in corner and tight places where traditional

methods and cleaning tools tend to push dirt into, making

it tough to reach and clean. Spray direct steam and wipe

clean with a wet cloth or paper towel.

1 Attach the Concentrator Nozzle by pressing the

nozzle onto the Accessory Hose until it clicks into

place. (ﬁg. 12)

2Press the power button to start the steamer.

For effective cleaning, hold the steam output nozzle

1-2 inches away from the surface you’re cleaning.

CAUTION: Do not press the power button until the

Concentrator Nozzle is snapped into the accessory

hose of your Handheld Steamer.

3To remove the Concentrator Nozzle, press and hold

the accessory release button, then pull it out of the

Accessory Hose.

CAUTION: Do not press the power button while

removing the Concentrator Nozzle. Avoid touching

the tip of the Concentrator Nozzle, as this will be very

hot after steaming.

NOTE: The Handheld Steamer may continue to emit

steam for a few seconds after the power button is

pressed to turn the unit off. This is normal, and the

steaming will eventually come to a stop.

ﬁg. 14

AFTER USE AND STORAGE

1Press the power button to turn the unit off. Unplug

the cord from the outlet and place the mop into the

upright position. Let the unit cool for 2-3 minutes.

2When you have ﬁnished using the Handheld Steamer,

reattach the handle to the handheld steamer.

3Remove the cleaning pad from the mop head by

placing one foot on the tab of the all-purpose carpet

pad and lifting the Shark®Multi-Function Steam Mop

Lite, avoiding bare skin contact with the hot pad or dirt.

4Empty the water tank before storage. Remove the

water tank cap and empty the tank over a sink.

Replace the water cap.

5To store the Shark®Multi-Function Steam Mop Lite

hanging up, ﬁrst remove the head (after it has cooled

and the steam has been released) then hang on a

large hook. (ﬁg. 15)

Care of Your Steam Mop

ﬁg. 15

USING THE GROUT SCRUBBER

Cleaning Tip: The Grout Scrubber is designed for

removing stubborn messes in hard-to-reach nooks,

corners and in grout where focused scrubbing power

may be needed. It can loosen and dislodge compact dirt

often found in corners and tight places where traditional

methods and cleaning tools tend to push dirt into,

making it difﬁcult to reach and clean. Scrub with the

Grout Scrubber and wipe clean with a cleaning cloth.

1Attach the Grout Scrubber by snapping into the

handle of the Accessory Hose until it clicks into

place. (ﬁg. 13)

2Press the power button to start steaming.

3To remove the Grout Scrubber, press and hold down

the Accessory release button. Then slide out the tool

out.

CAUTION: Turn the unit off before attaching or

removing the Grout Scrubber

ﬁg. 13

13 140800 862 0453 www.sharkclean.eu

DECALCIFYING YOUR STEAM MOP

Calcium and mineral deposits can build up and

impact the performance of your steam mop

over time. To extend the life of your product we

recommend that you use distilled water.

CARE OF YOUR CLEANING PADS

1 We recommend washing your cleaning pads

separately from other fabrics to avoid picking up

lint. For optimal cleaning performance, the pads

may need to be washed up to (3) three times. Only

use liquid detergent (no powder detergent). Do not

use any fabric softeners or bleach. Line dry. Do not

tumble dry. (ﬁg. 16)

2If there are loose threads on the cleaning pads,

carefully cut the thread with scissors. Do not pull on

them or cut at the base. (ﬁg. 17)

IMPORTANT: The cleaning pads may be very hot

from the steam. Use caution when removing. Let the

unit cool for 2-3 minutes.

ﬁg. 17

CLEANING THE NOZZLE

NOTE: To prevent clogging, it is recommended that

you periodically clean the Direct Steam Nozzle and

the extension hose stem.

1Your Handheld Steamer should not normally require

cleaning, however, should you notice a decrease in

the steam output, it may be necessary to remove

mineral deposits built up around the nozzles.

2Unplug the cleaner from the electrical outlet.

3Use a small diameter stiff metal wire, such as a

straightened metal paperclip, and carefully insert the

end of the wire into the nozzle oriﬁce. See illustration

above. (ﬁg. 18)

4Move the wire back and forth several times to remove

any deposits.

5Plug in the appliance to the power outlet and test

steam output.

ﬁg. 18

ﬁg. 16

40°

Troubleshooting Guide

PROBLEM POSSIBLE REASONS & SOLUTIONS

The Shark®Multi-Function

Steam Mop Lite will not

turn-on.

Your steam mop should be securely plugged into an electrical outlet only.

Check your fuse or breaker.

The unit will not make steam.

Is there water in the water tank? If not, add water to your steam mop following

instructions on page 4.

When using the unit in the handheld mode, ensure that you are holding the

handheld unit horizontally to optimize the steam output. Do not hold the

handheld unit vertically as this will impede steam production. Use the hose with

your chosen accessory to reach difﬁcult areas and above ﬂoor cleaning whilst

maintaining the horizontal position of the handheld unit.

If the unit still does not make steam, follow the instructions on page 13 to clean

the nozzle.

The Shark®Multi-Function

Steam Mop Lite leaves water

on the ﬂoor.

Check to see if your cleaning pad is too wet. We recommend you unplug the

steam mop and change the cleaning pad.

Make sure the cleaning pad is attached correctly.

The Shark®Multi-Function

Steam Mop Lite left a white

spot on the ﬂoor.

Do not leave your steam mop on the ﬂoor with a damp or wet cleaning pad.

If you’re using tap water, we recommend switching to distilled water.

Make sure the cap is securely on the water tank.

Floors are cloudy, streaky or

spotty after steaming.

The cleaning pad might be dirty. Change the cleaning pad.

If you washed the cleaning pad with powder detergent, then your pad could be

damaged and require replacement. Replacement pads are available at

www.sharkclean.eu.

This could also be an indication of prior soap or grease residue that has

accumulated on the ﬂoor. As our steam mops use only a small amount of

water, it may not be wet enough to rinse off the accumulation that the steam

is bringing to the surface. We suggest rinsing the ﬂoor with nothing but water,

letting it dry, and then steam mopping again with a clean pad. One or more

rinses generally removes the residue.

A more stubborn case may require you to rinse the ﬂoor with a mix of one part

vinegar and two parts water.

The Shark®Multi-Function

Steam Mop Lite is hard to

push.

Make sure the cleaning pad is attached correctly.

Check to see if the cleaning pad is excessively dirty. If so, replace the cleaning

pad.

Care of Your Steam Mop- cont.

IPX4

Euro-Pro Europe LTD

15 Mariner Court

Calder Park

Wakeﬁeld

WF4 3FL

0800 862 0453

www.sharkclean.eu

Technical Details

Model number: S7000UK 11

Input: 1250 Watts

Main unit voltage: 220-240V~, 50/60Hz

Euro-Pro and Shark are trademarks of Euro-Pro

Operating LLC. All other brand names may be

trademarks of their respective owners.

Illustrations may differ from actual product.

PRINTED IN CHINA

S7000UK_11_IB_E_150623_4

Inhaltsverzeichnis

Andere Sharp Dampfreiniger Handbücher

Sharp

Sharp S3455UKE Bedienungsanleitung

Beliebte Dampfreiniger Handbücher anderer Marken

Oreck

Oreck STEAM-IT STEAM100LRH Bedienungsanleitung

Beautural

Beautural YPZ-146 Bedienungsanleitung

MPM

MPM MZP-02 Bedienungsanleitung

Electrolux

Electrolux Refine 500 Bedienungsanleitung

Kärcher

Kärcher SC 3 Premium Bedienungsanleitung

Shark

Shark PRO Steam & Spray Bedienungs- und Wartungsanleitung

Jula

Jula 802-337 Bedienungsanleitung

Haan

Haan Floor Sanitizer MS-30 Bedienungsanleitung

Black & Decker

Black & Decker HSM13E1 Bedienungsanleitung

HOFFEN

HOFFEN GS-1231 Bedienungsanleitung

POLTI

POLTI VAPORETTO SYSTEME PRO Bedienungsanleitung

eta

eta AQUASIM PRO Bedienungsanleitung

Maxwell

Maxwell MW-3715 G Bedienungsanleitung

VAPamore

VAPamore Primo MR-100 Handbuch

Bestron

Bestron AZQ016 Bedienungsanleitung

Nilfisk-ALTO

Nilfisk-ALTO Steamtec 312 Bedienungsanleitung

Tempo di saldi

Tempo di saldi SPINSCRUBBER Bedienungsanleitung

DOMENA

DOMENA HYGIAFLOR Bedienungsanleitung