ShelterLogic 58542 Bedienungsanleitung

22x24x12 Peak Style Run-in Shed

05-58542-0B 08/06/08

PAGE 1

150 Callendar Road

Watertown, CT 06795

ATTENTION:

BOLTS ARE NOT

NEEDED OR

INCLUDED FOR EVERY

CONNECTION BUT

MAY BE

PURCHASED BY CALLING

THE NUMBER BELOW.

FOR MISSING OR

REPLACEMENT PARTS

OR QUESTIONS

PLEASE CONTACT

CUSTOMER SERVICE:

1.800.524.9970

BASIC HAND TOOLS

REQUIRED FOR ASSEMBLY:

• Adjustable Wrench

• Rubber Mallet

Model #

58542

Please read instructions completely before assembly

Description Part # Qty.

Cross Rail Plain Ends 45"L 11105

11068

Cross Rail Swedged 48 1/2”L 11103

11101

Corner Upright Leg

11016 4

Side Bend Tube 11013 12

End Top Bend 11136 2

Middle Top Bend 11135 4

Extension 59.4"L 24

Straight Leg Tube

Cross Rail Swedged

38”L

50 1/2”L

11019

11102

Wind Brace 30”L 11095 4

Wind Brace 54.2”L 11093 4

Description Part # Qty.

Cross Rail Plain End 46.6"L

11104 2

Cross Rail Plain End 48.5"L

All-Weather Cover 1A7254 1

Protective Boot 800196 4

4-Way Cover Rail Clamp

3-Way Cover Rail Clamp

11107

11106 8

5/16"x 4" Round Head Bolt

5/16"x 4" Bolt

5/16"x 2 3/4" Bolt

5/16"x 2 1/4" Bolt

5/16"x 2" Bolt

5/16" Nuts

11133 4

11132 8

11131 60

11130 20

11270 8

648 6

690

10040

102

Bolt Cap 11150 24

5/16"x 4 1/2" Bolt 11134 4

Ratchet

Temporary 30”Auger Anchors

Cable - 1’ Lengths

Cable Clamps

822

Base Feet

Page 2

Basic Frame Assembly

STEP 1

STEP 2

Fit together an end rib using the following parts, (1) #11136 3-Way Top Connector, (4) #11068 Swedged Rafter Pole, (2)

#11013 Side Bend Tube and (2) #11016 Bend Corner Leg. Using (8) 11131 5/16 X 2 3/4" bolts and (8) 690 5/16" nuts

securely fasten the joints of all parts. Lay this rib on the ground at the rear of your shelters designated location. For a 12'

tall building be sure to include the two foot extension pipe (4551).

NOTE: Be sure that all of the heads of the bolts are facing toward the outside of the rib.

Fit together the first middle rib using the following parts, (1) #11135 Top Bend Tube, (4) #11068 Swedged Rafter Pole, (2)

#11013 Side Bend Tube and (2) #11019 Swedged Upright Tube. Using (8) #11131 5/16 X 2 3/4" bolts and (8) #690 5/16"

nuts. Securely fasten the joints of all parts. Lay this rib on the ground near the first end rib. For a 12' tall building be sure

to include the two foot extension pipe (4551).

Assemble the wind braces as shown in the

illustrations.

Fig.1

10' Tall Frame 12' Tall Frame

Fig.2

Use 11131

5/16" x 2 3/4"

Bolts

11136

11068

11013

11016

4551

Use 11131

5/16" x 2 3/4"

Bolts

11019

4551

11135

11068

11013

Use 11131

5/16" x 2 3/4"

Bolts

11136

11068

11013

11016

Use 11131

5/16" x 2 3/4"

Bolts

11135

11068

11013

11019

STEP 3

For Basic Frame

For 12' Tall Building

#648

#690

#11095

#11093

#648

#800053

#690

#648

#690

#11095

#11093

Page 3

STEP 4

STEP 5

STEP 6

middle leg

clamps

11107

11130

690

corner leg

clamps

11130

690

11106

11013

11016 11105

11106

11107

Wind Brace

11134 Bolt

11102

11013

11016

11102

11105

11106

11107

11019

11134 Bolt 11131 Bolt

11132 Bolt

With help stand the first end rib vertically and lean against a permanent structure such as a tree or a fence. Attach the

plain end of a #11102 horizontal tube and a wind brace assembly to the first rib using a #11134 5/16 X 4 1/2" bolt and

a #690 5/16" nut on the INSIDE of the bow, on each side bend just above the joint of the side bend/extension. Repeat

the same steps on opposite side.

Place (2) #11106 3-Way Clamps around #11016 Bent Leg. Insert #11105 Cover Rail into the clamp and attach using a

#648 5/16 X 2" bolt and #690 5/16" nut. Position the clamp about five inches above the ground and tighten the nut

and bolt finger tight. Repeat the same steps on opposite side.

With help position the first middle rib about four feet from the first end rib. While one person holds the middle rib vertical

the other person should raise the previously installed #11102 cross rail and place another #11102 over each of the previous.

Raise the two rails so they are horizontal and attach to the middle cross rail using a #11132 5/16 X 4" bolt and a #690

5/16" nut. Attach a #11107 4-Way Clamp to the end of the (2) cover rail tubes using a #648 5/16 X 2" bolt and a #690 5/16"

nut. Place the clamp around the middle leg and insert a #11105 cover rail into the opposite side of the clamp and attach

with a #648 5/16 X 2" bolt and a #690 5/16" nut. Position the clamp about five inches above the ground and tighten

finger tight. Raise the cross brace to the middle rib and attach it to the rib using a #11131 5/16 X 2 3/4" bolt and a #690

5/16" nut, Repeat these steps for the opposite side.

Repeat the cross rail installation for the remaining middle legs.

Page 4

STEP 10 ATTACHING & SECURING BASE FEET

Install the top cross rail assembly starting with #11103 Cross

Rail Swedged 48 1/2"L inserted into the End 2-Way Connector.

Secure with a #648 5/16 X 2" bolt and #690 nut. Place the

plain end of a #11103 Cross Rail Swedged over the end and

put the joint on the top of the middle rib. Secure with a #11133

5/16 X 4" Round Head Bolt and #690 Nut. Continue adding

#11102 Cross Rails and finish with the #11101 Cross Rail Plain

End inserted into the last end 3-way connector and secure with

a #648 5/16 X 2" bolt and #690 nut.

NOTE: Use the special Round Head Bolts for securing the

top rail to the middle ribs only!!!

Step 8 Installing T

Step 9 SQUARING THE SHELTER

op Rail

Install the Top Rail

Over all Middle Ribs

Check that the shelter's width is correct from the outside to

outside of the uprights at ground level. Check also that the

shelter is square by measuring diagonally from corner to

corner at ground level.

The two measurements must be within 2 inches of each

other.

Depending on the model you have purchased, your base feet will either fit

onto the outside of the leg poles, or slide inside the leg poles. After installing

Base Feet Plates onto bottom of Middle leg Poles, be sure to line up the

pre-drilled hole in the leg with the pre-drilled hole in the base foot. Insert

5/16" x 2 3/4" bolts all the way through leg and foot, to other side, secure with

nuts.

STEP 7

Install the other end rib as you had installed all the middle ribs only use #11104 crossrails and attach the sliding crossrail

using the remaining 3-way coverrail clamps.

Note: The final windbrace assemblies should be installed as shown. Be sure the upper of the windbraces are

installed between the rib and crossrail

22'

Page 5

STEP 11 INSTALLING AUGER ANCHORS

Using a 3/4" pipe or steel rod, (a car tire iron works also) placed

through the eyelet on the auger, screw it into the ground. Start at

the four corners of the unit and space the remainder out evenly.

Be sure to screw the anchor in fully (the eyelet should be a level

where it can be securely attached to the frame. Wrap the cable

provided through the eyelet of the anchor and around the frame.

Secure the cable with the clamp(s) provided.

WARNING:

DO NOT INSTALL THE END PANELS OR COVER ON THE

SHELTER UNTIL IT HAS BEEN PROPERLY ANCHORED.

Page 4

STEP 12 SECURING YOUR COVER:

* The ratchets

should be checked

monthly to make sure

the cover is tight.

Outside Corner View

Pull the cover over the frame. The welded in webbing should be at the front and back of the building. Also note that the

pocket with cutouts, running along the sides of the cover should be on the inside and near the ground. Insert the "S" hook

from the ratchets into the hole in the leg of the frame. Next, insert the webbing into the spindle of the ratchet and tighten

ratchet until the webbing overlaps itself, do not tighten all the way yet. Check to be sure the cover still has an even overhang

on the front and rear, adjust as necessary. Once the cover is even, finish tightening the ratchets, alternating from corner to

corner to ensure the cover stays even.

After the cover is tight end to end, remove the cross rails and connectors on one side of the frame and place them into

the pockets between the cutouts. Attach the crossrails using the 3-way and 4-way cover rail clamps around the uprights and

loosey fasten with the 1/4" x 1 5/8" bolts and 1/4" nuts. Check that the rails are evenly spaced above the ground on both

sides. Push down on the connectors one at a time to tension the cover and tighten the bolts to hold tightly.

Warning:

Do not leave a partially or fully covered unit without being fully anchored. Serious injury to persons or property

could result.

Fig. 11

Fig. 12

Fig. 8

corner leg

clamps

10115

1010

10112

Fig.9

middle leg

clamps

10115

10111

1010

Fig.10

STEP 8

Page 6

Fig. 13

Find the open side of the protective boot and open it.

Insert the foot of the corner leg into the protective boot.

When the foot is all the way in the boot insert the top edge

of the boot into the hem of the cover (Fig 13).

When complete secure the Velcro on the open side of the boot to

close the boot.

For Replacement Parts or Help with assembly, Please call:

Customer Service:

1-800-524-9970

8am-7pm

Mon-Sat EST

150 Callender Road

Watertown, CT 06795

Inhaltsverzeichnis

Andere ShelterLogic Unterschlupf Handbücher

ShelterLogic

ShelterLogic Shed-In-a-Box E Series Bedienungsanleitung

ShelterLogic

ShelterLogic 60180 Bedienungsanleitung

ShelterLogic

ShelterLogic Shed-in-a-Box 70401 Bedienungsanleitung

ShelterLogic

ShelterLogic 23530 Bedienungsanleitung

ShelterLogic

ShelterLogic 86063EU Bedienungsanleitung

ShelterLogic

ShelterLogic ShelterCoat 12'W x 8'H Peak Bedienungsanleitung

ShelterLogic

ShelterLogic Super Max 26773AC Bedienungsanleitung

ShelterLogic

ShelterLogic Shed-in-a-Box Bedienungsanleitung

ShelterLogic

ShelterLogic Power-Up 90101 Bedienungsanleitung

ShelterLogic

ShelterLogic 62656 Bedienungsanleitung

ShelterLogic

ShelterLogic GROW IT Bedienungsanleitung

ShelterLogic

ShelterLogic Super Max 26780 Bedienungsanleitung

ShelterLogic

ShelterLogic Run-in Shed 51341 Betriebsanleitung

ShelterLogic

ShelterLogic 51351 Bedienungsanleitung

Beliebte Unterschlupf Handbücher anderer Marken

Tempo Fitness

Tempo Fitness S11 Bedienungsanleitung

Tuindeco

Tuindeco 42.7906 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1605 Bedienungsanleitung

TMG

TMG TMG-DT5040CG Bedienungsanleitung

TMG

TMG TMG-DT3063-PRO Bedienungsanleitung

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Bedienungsanleitung

Kampa

Kampa Poled Shelter 300 Bedienungsanleitung

Harnois

Harnois TA-R Bedienungsanleitung

Shelters4Less

Shelters4Less SR1551 Bedienungsanleitung

TMG

TMG TMG-DT50FW8 Bedienungsanleitung

Vikre Handel AS

Vikre Handel AS JIT-1216 Bedienungsanleitung

VARNA buildings

VARNA buildings C2020H Bedienungsanleitung

Storage Canopy

Storage Canopy C3340R Bedienungsanleitung

Frabill

Frabill ICE HUNTER 195 Bedienungsanleitung

Shelters4Less

Shelters4Less SR1588 Bedienungsanleitung

Sealey

Sealey Power Products GSS150819SD Bedienungsanleitung

Crivit

Crivit 104155 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1558-F Bedienungsanleitung