ShelterLogic Peak Style 8' W x 8' H Bedienungsanleitung

ShelterLogic, LLC

150 Callender Road

Watertown, CT 06795

www.shelterlogic.com

1-800-524-9970

1-800-559-6175

Canada:

Assembly Instructions

8' W x 8' H or 10' H

Peak Style

Frame Assembly

Before you start: 2+ individuals recommended for assembly, approximate time 3 hours.

Recommended tools: Power Drill, Safety Glasses, Rope, Tape Measure, Ratchet with Socket Set,

Adjustable Wrench, Step Ladder, Rubber Mallet, Utility Knife, 5/8 Concrete Drill Bit, Sledge Hammer.

05-10DT13-0A

Page 2

8'W x 8'H Peak Style Frame Assembly

Please read and understand instructions completely before assembly.

Layout out frame parts as shown.

ATTENTION:

FOR MISSING OR

REPLACEMENT PARTS

OR QUESTIONS, PLEASE

CONTACT

CUSTOMER SERVICE:

1.800.524.9970

CANADA 1.800.559.6175

END RIB

CROSS

RAIL

TOP RAIL

MIDDLE RIBS

END RIB

WIND

BRACE

COVER RAIL

8' W X 8' H

ITEM NO. DESCRIPTION PART NO.

SWED.UPRIGHT TUBE 67 3/4"X1-5/8"D. 1 END

TOP BEND TUBE 15"X1-5/8" DIA.

SIDE BEND TUBE 15"X1-5/8" DIA.

RAFTER PIPE, 42X1190XT1,4 SWG BOTH ENDS GRY

CORNER UPRIGHT TUBE 57 3/4"X1-5/8" DIA.

BEND CORNER LEG 21"X1-5/8" DIA.

CROSS RAIL 48-1/2"X1.163",PLAIN ENDS 2 H

CROSS RAIL 50-1/2"X1.163", 1 SWDG 2 HOLE

CROSS RAIL PLAIN END 47"X1-1/8" DIA.

CROSS RAIL PLAIN ENDS 45 3/4"L, 2 HOLES

CROSS RAIL SWEDGED 48 7/8"X1-1/8" DIA.

BASE FOOT, 1-3/8 STEEL, GRY

3-WAY TOP CONNECTOR

3-WAY COVER RAIL CLAMP 1 5/8" PIPE

4-WAY COVER RAIL CLAMP

WIND BRACE FLAT ENDS 62-3/4"X1-1/8"DIA.

SHELTERLOCK ANTI-RACK DEVICE 42X28MM

BOLT, CARRIAGE,1/4"X1-5/8"

BOLT, CARRIAGE 1/4"x2"

BOLT, CARRIAGE 1/4" X 3"

BOLT, LADDER RD,F/TOPCRESTS,1/4"X3 1/2"L

NUT, HEX, 1/4-20

ANCHOR, AUGER 3"X15" WITH CABLE & CLAMP

10126

10131

10132

10127

10128

02031

02030

10134

10110

10133

10113

10121

10112

10111

10135

800260

10115

10114

00670

00669

01010

00847

BOLT CAPS

24 10150

21/22

21/22 13

05-10DT13-0A

800465

Page 3

8'W x 10'H Peak Style Frame Assembly

Please read and understand instructions completely before assembly.

Layout out frame parts as shown.

ATTENTION:

FOR MISSING OR

REPLACEMENT PARTS

OR QUESTIONS, PLEASE

CONTACT

CUSTOMER SERVICE:

1.800.524.9970

CANADA 1.800.559.6175

8' W X 10' H

END RIB

CROSS

RAIL

TOP RAIL

MIDDLE RIBS

END RIB

WIND

BRACE

COVER RAIL

ITEM NO. DESCRIPTION PART NO.

SWED.UPRIGHT TUBE 67 3/4"X1-5/8"D. 1 END

TOP BEND TUBE 15"X1-5/8" DIA.

SIDE BEND TUBE 15"X1-5/8" DIA.

RAFTER PIPE, 42X1190XT1,4 SWG BOTH ENDS GRY

CORNER UPRIGHT TUBE 57 3/4"X1-5/8" DIA.

BEND CORNER LEG 21"X1-5/8" DIA.

CROSS RAIL 48-1/2"X1.163",PLAIN ENDS 2 H

CROSS RAIL 50-1/2"X1.163", 1 SWDG 2 HOLE

CROSS RAIL PLAIN END 47"X1-1/8" DIA.

CROSS RAIL PLAIN ENDS 45 3/4"L, 2 HOLES

CROSS RAIL SWEDGED 48 7/8"X1-1/8" DIA.

BASE FOOT, 1-3/8 STEEL, GRY

3-WAY TOP CONNECTOR

3-WAY COVER RAIL CLAMP 1 5/8" PIPE

4-WAY COVER RAIL CLAMP

WIND BRACE FLAT ENDS 62-3/4"X1-1/8"DIA.

SHELTERLOCK ANTI-RACK DEVICE 42X28MM

BOLT, CARRIAGE,1/4"X1-5/8"

BOLT, CARRIAGE 1/4"x2"

BOLT, CARRIAGE 1/4" X 3"

BOLT, LADDER RD,F/TOPCRESTS,1/4"X3 1/2"L

NUT, HEX, 1/4-20

ANCHOR, AUGER 3"X15" WITH CABLE & CLAMP

10126

10131

10132

10127

10128

02031

02030

10134

10110

10133

10113

10121

10112

10111

10135

800260

10115

10114

00670

00669

01010

00847

BOLT CAPS

24 10150

10223

25 UPRIGHT EXTENSION, 27” SWEDGED-1 SIDE 1 5/8 D.

21/22

21/22 13

05-10DT13-0A

800465

Page 4

ASSEMBLY OF PEAK STYLE GARAGE SHELTER

NOTE FOR FRAME EXTENSION KIT: 8’ x 8’ is the base frame dimension. Your model may have more middle

ribs than shown in the illustrations. You will receive one extra rib for every extra 4 feet of building length that you

purchase. The basic frame assembly will remain the same. The cover will be the correct size for the length of the

building ordered.

1. PLOTTING AND SQUARING UP THE FRAME:

A. Before building your shelter, you should choose a at area

on your property and plot your shelter. Stake out the area for

the frame in the desired spot. Check that it measures 10’ in

width and the length would be determined by the size shelter

you purchased. Tie a rope diagonally from corner to corner.

B. Measure across area, end to opposite end. See Detail A.

The measurement A and B should be equal.

ABLENGTH

BUILDING

DETAIL A

2. ASSEMBLE END AND MIDDLE RIBS:

DETAIL B

End Ribs

DETAIL C

Middle Ribs

#10114

2” Bolt

Item #19

All Connections

10' HIGH

8' HIGH

A. Assemble end and middle ribs as shown in Detail B and Detail C.

Securely fasten all of the joints with the hardware indicated.

10121

10132

10127

10128 10128

10131

10132

10126 10126

800465

800465 800465

800465

10113

10131

10132

10126 10126

800465

10113

10223

10132

800465

10223

10128

10127

10121

10128

#10114

2” Bolt

Item #19

All Connections

#10114

2” Bolt

Item #19

All Connections

#10114

2” Bolt

Item #19

All Connections

05-10DT13-0A

Page 5Page 5

3. INSTALL SIDE RAILS AND SHELTERLOCK™STABILIzER BLOCKS:

A. Place assembled rst end rib in the staked area. Place the

ShelterLock™on the upright as shown in Detail D. From the

outside of the rib insert the bolt through the upright and then

through the ShelterLock™.

B. Place the plain end of the side rail over the bolt and nest

it into the ShelterLock™. Install the nut onto the bolt and

tighten. Repeat these steps for the opposite side and all of

the remaining ribs. The side rails for the last rib will have two

plain ends.

4. INSTALL WIND BRACES:

A. Attach wind brace between the end rib and the rst

middle rib as shown in Detail E. Bolts attached at the

cross rails should be inserted facing inside the shelter.

5. INSTALL TOP RAIL:

A. Place the rst top rail under each end rib and secure it

with a bolt as shown in Detail F. The same cross rail should

lay on top of the all middle ribs. Secure the rails to the frame

with the hardware indicated in Detail F. The top rail attached

to the last rib will be installed under the pipe.

DETAIL D

DETAIL E

DETAIL F

FIRST

MIDDLE

RIB

WIND BRACE

END RIB

00669

10210

Install the Top Rail

OVER all Middle Ribs

UNDER First and Last Ribs

Fig. 2

800260

1010

10135

00670

02030

05-10DT13-0A

Page 6

6. SECURE BASE FEET:

A. Slide leg pipe over over the base feet, line up the holes in

the pipe with the holes in the feet and secure with the hard-

ware indicated in Detail G.

7. INSTALL AUGER ANCHORS:

A. Anchors must be placed inside shelter. Start at the corners

of the shelter. Insert a ¾” pipe or steel rod, through the eyelet

of the auger and screw the anchor into the ground. (If ground is

too hard, dig a hole with a shovel or post hole tool.)

OPTIONAL: Fill with cement.

B. Space out the remaining anchors evenly along the length of

the shelter. Screw the anchor into the ground until the eyelet is

sticking out of the ground by 1-2” so it can be anchored to the

legs.

C. Wrap the cable provided through the eyelet of the anchor

and around the frame as indicated in Detail H. Secure the cable

with the clamps provided.

D. Repeat for middle legs by attaching cable around foot plates.

8. zIPPER DOOR AND OR END PANEL INSTALLATION:

Secure

with bolt

and nut

DETAIL G

DETAIL H

A. Hold the end panel at the top center with the white inner

surface facing the inside of the shelter (if you have a white

shelter the inner surface has the visible weld seams).

B. Unscrew top rail from the top bend and place the webbing

in between. The top rail should pass through the loop of the

webbing. Reconnect top rail onto rib and secure it with the

screws indicated. See Detail I.

C. Remove the nut from the side rail and carefully pull

the side rail away from the ShelterLock™(pull away only

enough to pass the webbing through the connection). If

this connection has the wind brace on it remove the

wind brace end before pulling the side rail. Replace the

cross rail and wind brace. See Detail J. Replace the nut and

tighten. Repeat this on the other side.

D. At the bottom, where the webbing exits the pocket on

each side of end panel, pull webbing to remove the slack.

Be careful not to pull the webbing through the other side of

the panel.

E. Install the “S”- hook from the ratchet into the leg of the

shelter. Insert the webbing into the spindle of the ratchet

and pull tight. See Detail J. Wind the ratchet so that the web-

bing overlaps itself. Repeat this process on the other side of

the panel. Position the end panel so that it is centered on the

building.

F. Tighten the ratchets, alternating from one side to the other,

until the end panel is tight. Repeat these steps on the other

end of the building.

DETAIL I

INSIDE VIEW SIDE VIEW

DETAIL J

10114

01010

Slit in fabric

folded around

frame and

cross rails

inserted

through slits

ROPE

END LEGS MIDDLE

LEGS

Page 7

9. INSTALLING THE COVER ON THE FRAME:

A. Lay the cover on the ground next to the

frame with the inside of the cover (the side with

the pipe pockets) facing down and the webbing

on the front and rear of the corner of the build-

ing. Position the cover so that it is centered on

the frame, front to back. See Detail K.

B. Fold over the side so the pipe pocket is now

accessible. Insert a cover pipe into the pipe

pocket slot, at the rst middle rib from the front

and the rst middle rib from the rear. Some of

the pipe will be exposed. For long buildings it

may be necessary to use additional pipes in the

middle. See Detail L. Remove pocket pipe to

install later.

C. Tie the rope on each of the exposed pipes

and throw the other end of the rope over the

frame. See Detail M.

D. Move to the other side of the frame and pull

the cover over the frame with the rope. This

may require two or more people. See Detail N.

Check that the Logo reads upright as shown.

DETAIL K

DETAIL L

DETAIL M

DETAIL N

END PANELS

NOT SHOWN

FOR CLARITY

Page 8

10. SECURING YOUR COVER:

A. Install the “S”- hook from the ratchet assembly into the legs of

the shelter. Pull the webbing carefully to remove the slack from the

cover. Do not to pull the webbing through the opposite side of the

cover.

B. Insert the webbing through the spindle of the ratchet and pull

tight. See Detail O. Wind the ratchet until the webbing overlaps

itself. Repeat these steps on the opposite side, then repeat this

on the back side of the shelter.

C. When all of the corners are secured, adjust the cover front to

back so that it is centered. When the cover is centered, tighten all

of the ratchets. Do this in an “X” pattern to be sure it is tightened

evenly. See Detail O.

D. Install the cover rails (10110) by inserting them into the pipe

pockets on each side of the cover. Bolt (10115) the rails to the ribs

using the 3-way and 4-way clamps as shown in Detail P. Check

that the rails are evenly spaced 8” above the ground on both

sides. Push down on the cover rails and connectors, one at a

time, to tighten the bolted clamps and the cover.

IMPORTANT: Install bolt caps (10150) on exposed bolts on side

rails and wind braces to prevent injury. DETAIL O

OUTSIDE

CORNER

VIEW

10115

01010

11102

10115 10111

01010

DETAIL P

NOTE: CHECK THAT

YOUR COVER IS

CORRECTLY PLACED

ON THE FRAME.

The ShelterLogic®logo should line

up on the left front and right rear

corners near the top rail. If the logo

is not legible and positioned as

shown as “incorrect”, the cover has

not been put on the frame correctly.

CORRECT

INCORRECT

Check and

tighten Ratchets

and Cross Rails

monthly to ensure

the cover is tight.

Cover Tightening Tip

clamps

CORNER LEG MIDDLE LEG

WARNING: Serious injury to persons or property could result if cover is installed and shelter is not

completed and is left unattended. Shelter must be securely anchored until completed.

10110

05-10DT13-0A

Dieses Handbuch passt für folgende Modelle

Andere ShelterLogic Zelt Handbücher

ShelterLogic

ShelterLogic Peak Shelter Bedienungsanleitung

ShelterLogic

ShelterLogic 26775 Bedienungsanleitung

ShelterLogic

ShelterLogic STORE-IT 15577 Leitfaden

ShelterLogic

ShelterLogic 27273 Bedienungsanleitung

ShelterLogic

ShelterLogic 22556 Bedienungsanleitung

ShelterLogic

ShelterLogic ShelterTube 62807 Bedienungsanleitung

ShelterLogic

ShelterLogic 25769 Bedienungsanleitung

ShelterLogic

ShelterLogic 12'x20'x8' Bedienungsanleitung

ShelterLogic

ShelterLogic Shed-in-a-Box 70483 Bedienungsanleitung

ShelterLogic

ShelterLogic SUPERMAX 25770 Bedienungsanleitung

ShelterLogic

ShelterLogic Quick Shade Expedition EX64 Bedienungsanleitung

ShelterLogic

ShelterLogic Garage-in-a-Box RoundTop 62780 Bedienungsanleitung

ShelterLogic

ShelterLogic 22544 Bedienungsanleitung

ShelterLogic

ShelterLogic SuperMax 26767 Bedienungsanleitung

ShelterLogic

ShelterLogic 22568 Bedienungsanleitung

ShelterLogic

ShelterLogic ShelterTech 4,6 x 4,3 m Bedienungsanleitung

ShelterLogic

ShelterLogic SuperMax 26767 Bedienungsanleitung

ShelterLogic

ShelterLogic 14'W x 7'H Bedienungsanleitung

ShelterLogic

ShelterLogic Round Top Bedienungsanleitung

ShelterLogic

ShelterLogic Shed-in-a-Box CT 06795 Bedienungsanleitung

ShelterLogic

ShelterLogic Garage-in-a-Box SUV/Truck 62696 Bedienungsanleitung

ShelterLogic

ShelterLogic Shed-in-a-Box 70423 Bedienungsanleitung

ShelterLogic

ShelterLogic Shed-in-a-Box Bedienungsanleitung

ShelterLogic

ShelterLogic 22561 Bedienungsanleitung

Beliebte Zelt Handbücher anderer Marken

OZTENT

OZTENT JV SIGNATURE EDITION Bedienungsanleitung

GigaTent

GigaTent Summer Chalet Mini Tent Bedienungsanleitung

Outsunny

Outsunny 84C-230 Bedienungsanleitung

Napier

Napier SPORTZ COVE 61 Series Bedienungsanleitung

EuroTrail

EuroTrail ATLANTIS PRO Bedienungsanleitung

Reimo

Reimo Marina Bedienungsanleitung

TiiTENT

TiiTENT TB300 Bedienungsanleitung

Coleman

Coleman 2000033134 Installationsanleitung

Ozark Trail

Ozark Trail W784.1 Kurzanleitung

SlingFin

SlingFin CrossBow 2 Bedienungsanleitung

Coleman

Coleman 9600-141 Bedienungsanleitung

Palram

Palram Arizona 5000 Wave - WINGS Bedienungsanleitung

COVERPRO

COVERPRO 56184 Montageanleitung

Vango

Vango Zenith 100 Bedienungsanleitung

Costway

Costway PATIOJOY OP70818 Bedienungsanleitung

Clarke

Clarke PUC 88 Bedienungsanleitung

Coleman

Coleman MONTANA 14'x7' Bedienungsanleitung

Crivit Outdoor

Crivit Outdoor 96716 Bedienungsanleitung