Sherwood 50-1445 Bedienungsanleitung

Sonnet Fuel Conversion

Kit - 50-1445 & 50-1446

Please read and understand these instructions before installing. Failure to follow these

instructions carefully could cause property damage or personal injury.

Warning: This conversion kit shall be installed by a qualied service agency in accordance with

the manufacturer’s instructions and all applicable codes and requirements of the authority

having jurisdiction. If the information in these instructions is not followed exactly, a re,

explosion or production of carbon monoxide may result causing property damage, personal

injury or loss of life. The qualied service agency is responsible for the proper installation of

this kit. The installation is not proper or complete until the operation of the converted appliance

is checked as specied in the manufacturer’s instructions supplied with the kit.

Kit Parts List:

1 - Orice (Natural Gas #42 DMS or Propane #54 DMS)

1 - Conversion label 1 - Installation instruction sheet

Carefully inspect the orice supplied with this conversion kit. If it has been damaged or is missing, contact

your dealer, distributor or courier company to have them replaced before starting this installation. It is highly

recommended that you have your Sonnet Owner’s Manual with you to reference for this installation.

Conversion Kit Installation:

1. Shut the gas supply off at the

shut-off valve upstream of the unit.

CAUTION: The gas supply must

be shut off prior to disconnecting

the electrical power and before

proceeding with the conversion.

Allow the valve and unit to cool down

to room temperature. Figure 1: Door Release.

Figure 2: Door Removal.

2. Remove the glass door by placing the hooked end of the door release

tool in the hole on the door latch mechanism (see Figure 1) and pulling

the latch out then up over the lip on the door. When the two (2) latches

have been released, tilt the door forward and then lift up to unhook the

bottom door tabs. (see Figure 2).

Figure 4: Burner Removal.

3. Carefully remove the log set and ember

material if they are installed.

4. Using a T-20 screwdriver, remove the four (4) screws that

hold the burner in place (pointed out in Figure 19). Slide

the burner to the left (see Figure 4), then up and out of the

rebox.

Figure 3: Unfastening Burner.

Figure 7. Ignition assembly.

5. Convert the burner orice:

a) Remove the main burner orice

with a  inch deep socket (see

Figure 5).

b) Put a bead of pipe-thread

sealant or approved Teon tape on

the orice threads before installing

into the brass elbow.

c) Install the new orice from the

kit into the brass elbow (see Figure

6).

Figure 8: Turn Pilot Head.

d) Turn the pilot head a  turn

clockwise; back to its original position.

e) Close the front of the pilot shield.

7. Convert the gas regulator:

a) If unit is installed, pull the Sonnet

out from the replace. Ensure you do

not damage any of the venting or the

unit itself.

b) Using a 7/8” wrench, remove the

brass nut at the back left of the unit

(shown in Figure 10). A small black

spring depressor is clipped into the back of the brass nut.

c) Set the black spring depressor according to the gas used. The black spring depressor has two (2)

teeth at each end that t in to the brass nut but only one end has a larger disc. If the disc sits inside

the cap then the valve is set for natural gas and if the disc is pointing out then the valve is set for

propane (see Figure 11).

d) Reinstall the spring depressor and brass nut onto the unit.

e) Install the unit back into the replace. Check the venting and the unit itself are correctly

installed.

Pilot/

Orifice

Ignitor

Thermocouple

Figure 5: Orice Removal. Figure 6: Orice Replacement.

6. Convert the pilot:

a) Open the front of the pilot shield.

b) Using a 7/16” wrench, turn the pilot head a  turn counter-clockwise (shown in Figure 8).

c) Push the slider, with your nger or at head screwdriver, to the left if it is to be set for natural gas

or to the right for propane, red on the slider will be visible (see Figure 9).

Figure 11: Set Gas Type for

Valve.

Figure 10: Remove Brass Cap.

Figure 9: Set Gas Type to LP for

Regulator.

LPG

8. Reinstall the burner (reversing the procedure in step 4), log set & embers (refer to SECONDARY

INSTALLATION - INSTALLING LOG SET AND EMBERS in your Sonnet Owner’s Manual), and glass door. Note:

When installing the burner, the venturi shutter rod should slip into the venturi shutter adjustment

hole.

Warning: Never run the unit without the glass door

installed.

9. Open the shut-off valve at the gas line to the unit.

10. Use a small brush to apply a warm soapy water solution to all

gas connections (use half dish soap and half warm water). If

Figure 13: Adjust Venturi Air

a gas leak is present, bubbling will occur. Gas leaks

can be repaired by using an approved pipe thread

sealant or approved Teon tape. NEVER USE AN

OPEN FLAME WHEN TESTING FOR LEAKS. Check

the gas pressure of the appliance, refer to INITIAL

INSTALLATION - GAS LINE CONNECTION in your Sonnet

Owner’s Manual and Table 1.

11. Reconnect the electrical power to the unit.

12. Light the pilot and check for proper ames (see

Figure 12). Light the burner in both the “HI” and

“LO” positions to verify proper burner ignition and

Figure 12: Pilot Flame.

operation and proper ame appearance. The amount of air to the venturi may need to be adjusted

using the rod under the rebox. Pull the rod forward for more air or push it in for less air (see Figure

13). Also refer to Figure 14 for a ame appearance picture.

13. MAKE SURE that the conversion label is installed on or close to the rating label to signify that the unit

has been converted to a different fuel type.

Figure 14. Sonnet burning.

Part Number Part Description

50-1445 Sonnet Conversion Kit LP To NG Maxitrol

50-1446 Sonnet Conversion Kit NG To LP Maxitrol

MANUFACTURED BY:

SHERWOOD INDUSTRIES LTD.

6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3

www.envirore.biz

November 7, 2006

C-11195

Table 1: Orice and Pressure Information.

Main Burner Natural Gas Propane Gas

Orice: #42 DMS #54 DMS

Manifold Press: 4.0 W.C. (0.99 KPa) 10.0 W.C. (2.47 KPa)

Min. Manifold Press: 0.2 W.C. (0.05 KPa) 2.3 W.C. (0.57 KPa)

Max. Supply Press: 7.0 W.C. (1.74 KPa) 13.0 W.C. (3.28 KPa)

Min. Supply Press: 5.0 W.C. (1.24 KPa) 12.0 W.C. (2.96 KPa)

Max. Input: 26,600 BTU/hr (7.79 KW) 21,300 BTU/hr (6.24 KW)

Min. Input: 6,500 BTU/hr (1.9 KW) 11,400 BTU/hr (3.34 KW)

NEVER USE AN OPEN FLAME FOR LEAK TESTING.

Dieses Handbuch passt für folgende Modelle

Andere Sherwood Kaminzubehör Handbücher

Sherwood

Sherwood Westgate DV48 Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung