Shindaiwa 80575B Bedienungsanleitung

- 1 -

INSTRUCTION SHEET

MODEL 80575B TRIMMER TO BRUSHCUTTER CONVERSION KIT

P/N X7672231900

Model 80575B Trimmer to Brushcutter Conversion Kit

NO. PART NUMBER QTY. DESCRIPTION

1C405000420 1BAR, BARRIER

290030020022 10 PIN, COTTER 2×22

390051300010 1NUT 10×1.25 LH

4C535000150 1PLATE, ADAPTER - LOWER

561031307132 1PLATE, ADAPTER - UPPER

6P021050520 1DEBRIS SHIELD KIT - BLADE

7V805000170 3+BOLT, TORX 5×25

8C552000240 1+PLATE, SHIELD

9C550000770 1+SHIELD, DEBRIS - BLADE

10 90056250005 3+NUT, LOCK M5

11 C646000060 1HANGER, HARNESS

12 V805000140 1BOLT, TORX 5×12

13 C062000390 1HARNESS ASSY, SHOULDER

14 C644000080 1+PAD, SHOULDER

15 C649000200 1+HOOK, SNAP

16 X605000060 1WRENCH, T27 80×30

17 X605000100 1WRENCH, ALLEN 4 MM

18 X505005890 1LABEL, CAUTION (BLADE CAPABLE)

19 61031507130 1SPACER 11.8×15×9

READ THE

OPERATOR’S MANUAL

WEAR HEARING AND ANSI Z8 7.1

APPROVED EYE PROTECTION

KEEP BYSTANDERSAWAY

AT LEAST 50 FEET (1 5m )

BEWARE OF THROWN OR

RICOCHETED OBJECTS

USE HANDLEBAR OR BARRIER

WHEN OPERATING WITH A BLADE

WEAR HARNESS WHEN

OPERATING WITH A BLADE

BEWARE OF

BLADE THRUST

50FEET

(15m

)

8”

BARRIER

18 6

- 2 -

P/N X7672231900

Introduction

These are instructions to convert a grass trimmer to a

blade capable unit. This is not an Owner’s/Operator’s

manual. Information on how to operate and maintain

the unit can be found in the Owner’s/Operator’s man-

ual for the unit you are converting. This kit contains

a cutting attachment shield that has been redesigned

to provide better visibility and a larger cutting swath

when used as a grass trimmer.

Procedure

Remove The Existing Cutting Attachment Shield

1. Align locking hole (A) in adapter plate with

notch in edge of gear case and insert locking

tool (A).

2. Insert locking tool (B).

3. Turn line head (C) clockwise to remove it from

the shaft. Remove the locking tool.

4. Remove shield plate screws (D), shield plate (E),

plastic shield (F), and adapter plate (G). Retain

parts for conversion back to nylon line head op-

eration.

Remove The Gear Case

1. Remove gear case locating screw (H), loosen

gear case clamp bolt(s) (I), remove the gear case

- 3 -

P/N X7672231900

One Bolt Gear Case (gear case ratio 1.62:1)

Two Bolt Gear Case (gear case ratio 1.57:1)

Remove The Handle Assembly

Install The Harness Hangar

1. Slide harness hangar (J) onto main pipe (K) and

position as shown. Loosely secure the hangar

with one 5 x 12 Torx® bolt.

- 4 -

P/N X7672231900

Install The Handle Assembly With The Barrier

Bar

Install The Gear Case

1. Install the gear case onto the main pipe. Align the

locating hole on gear case with locating hole (L)

in the main pipe. Install the locating screw and

tighten the clamping bolt(s).

One Bolt Gear Case (gear case ratio 1.62:1):

Two Bolt Gear Case (gear case ratio 1.57:1)

Blade AssemblyCAUTION

Always install the debris shield. Operating the

unit without the debris shield installed can re-

sult in serious personal injury.

NOTICE

Use a new cotter pin each time a blade is in-

stalled. Do not reuse a cotter pin.

Refer to the specic gear case assembly diagrams on

the following pages.

The orientation and the order of the components must

match what is shown in the diagrams.

The rotation arrows on the blade must match the rota-

tion arrow (A) shown on the debris shield.

Note: The image of the blade is a representation only.

- 5 -

P/N X7672231900

Assemble As Shown: One Bolt Gear Case (gear case ratio 1.62:1)

The models listed below require the use of the spacer (reference No. 6)

Models Serial Number Range

T235 T46714008001 and up

T235 T88913001001 and up

T262 All T262 models

NO. PART NUMBER QTY. DESCRIPTION

190030020022 1PIN, COTTER 2×22

290051300010 1NUT 10×1.25 LH

3C535000150 1PLATE, ADAPTER - LOWER

4 – 1 BLADE (AS REQUIRED)

561031307132 1PLATE, ADAPTER - UPPER

661031507130 1SPACER 11.8×15×9

7V805000170 3BOLT, TORX 5×25

8C552000240 1PLATE, SHIELD

9C550000770 1SHIELD, DEBRIS - BLADE

10 90056250005 3NUT, LOCK M5

8”, 80 Tooth Brush Blade - 20mm Arbor

Hoja de 80 Dientes para Maleza de 20 cm - Árbol de 20mm

Lame à 80 Dents de Débroussaillage de 20 cm - Arbre de 20 mm

- 6 -

P/N X7672231900

Assemble As Shown: Two Bolt Gear Case (gear case ratio 1.57:1)

Models Serial Number Range

T235 Models with serial number prex S955, S956, S957,

and T762.

T254 All T254 models.

T344 All T344 models.

NO. PART NUMBER QTY. DESCRIPTION

190030020022 1PIN, COTTER 2×22

290051300010 1NUT 10×1.25 LH

3C535000150 1PLATE, ADAPTER - LOWER

4 – 1 BLADE (AS REQUIRED)

561031307132 1PLATE, ADAPTER - UPPER

6V805000170 3+BOLT, TORX 5×25

7C552000240 1+PLATE, SHIELD

8C550000770 1+SHIELD, DEBRIS -

BLADE

990056250005 3+NUT, LOCK M5

8”, 80 Tooth Brush Blade - 20mm Arbor

Hoja de 80 Dientes para Maleza de 20 cm - Árbol de 20mm

Lame à 80 Dents de Débroussaillage de 20 cm - Arbre de 20 mm

- 7 -

P/N X7672231900

Balance The Unit

Adjust the postion of the harness hangar so the unit

balances two to three inches above the cutting surface.

Use of the Shoulder/Waist Harness is recommended

for all Trimmer/Brushcutter use, not just Blade oper-

ation. The Shoulder/Waist Harness when used in a

trimming operation with nylon line head suspends the

trimmer from the operator’s shoulder and reduces op-

erator fatigue.

During blade operation, the same fatigue reduction is

achieved. Safety to the operator is also enhanced by

reducing the possibility of blade contact with the opera-

tor’s hands and feet by restricting trimmer movement..

- 8 -

P/N X7672231900

Andere Shindaiwa Freischneider Handbücher

Shindaiwa

Shindaiwa BP530 Bedienungsanleitung

Shindaiwa

Shindaiwa X7502831600 Betriebsanleitung

Shindaiwa

Shindaiwa 81188 Betriebsanleitung

Shindaiwa

Shindaiwa BP45 Bedienungsanleitung

Shindaiwa

Shindaiwa 89302 Betriebsanleitung

Shindaiwa

Shindaiwa BP35 Betriebsanleitung

Shindaiwa

Shindaiwa 89304 Betriebsanleitung

Shindaiwa

Shindaiwa 81714 Betriebsanleitung

Shindaiwa

Shindaiwa C254 Betriebsanleitung

Shindaiwa

Shindaiwa 81704 Betriebsanleitung

Shindaiwa

Shindaiwa C344 Betriebsanleitung

Shindaiwa

Shindaiwa 80562 Kurzanleitung

Shindaiwa

Shindaiwa 65004 Betriebsanleitung

Shindaiwa

Shindaiwa BP530 Bedienungsanleitung

Shindaiwa

Shindaiwa C242 Betriebsanleitung

Shindaiwa

Shindaiwa B450 Bedienungsanleitung

Shindaiwa

Shindaiwa 89303 Betriebsanleitung

Shindaiwa

Shindaiwa AHS254 Betriebsanleitung

Shindaiwa

Shindaiwa BP35 Bedienungsanleitung

Shindaiwa

Shindaiwa C282 Betriebsanleitung

Shindaiwa

Shindaiwa C282 Betriebsanleitung

Shindaiwa

Shindaiwa 81359 Betriebsanleitung

Shindaiwa

Shindaiwa X7502825900 Betriebsanleitung

Shindaiwa

Shindaiwa 81644 Betriebsanleitung

Beliebte Freischneider Handbücher anderer Marken

Echo

Echo SRM-265ES Series Montageanleitung

Victus

Victus VB 260 L Bedienungsanleitung

Solo

Solo 128L Bedienungsanleitung

Stihl

Stihl FS 410 C-M Bedienungsanleitung

CanyCom

CanyCom CMX 253 Bedienungsanleitung

Makita

Makita EBH340U Bedienungsanleitung

EGO

EGO BCA1220 Bedienungsanleitung

VARO

VARO Powerplus POWXG3016 Bedienungsanleitung

Stihl

Stihl FS 510 C Bedienungsanleitung

Lawn-King

Lawn-King FW35E Bedienungs- und Montageanleitung

Husqvarna

Husqvarna 553RBX Bedienungsanleitung

Ryobi

Ryobi RBC430SBS Bedienungsanleitung

RedMax

RedMax EXtreme EXZ2401S-BC Betriebsanleitung

Vito Agro

Vito Agro VIR43E Bedienungsanleitung

Black & Decker

Black & Decker 82267 Bedienungsanleitung

Agrimate

Agrimate AM-3000-BC-2S-WC-PRO Bedienungsanleitung

Echo

Echo SRM-410ES Bedienungsanleitung

PrimAster

PrimAster PMAFS 40 Bedienungsanleitung