Show Tec Titan Strobe blaze Bedienungsanleitung

Titan Strobe BLAZE V1

Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands

ENGLISH

Ordercode: 40297

MANUAL

 
 
 1 
 
Ordercode: 40297 
Titan Strobe BLAZE 
Table of contents 
 
Warning ...............................................................................................................................................................................2 
Safety Instructions .........................................................................................................................................................2 
Operating Determinations ..........................................................................................................................................4 
Rigging ............................................................................................................................................................................4 
Connection with the mains.........................................................................................................................................5 
Return Procedure..........................................................................................................................................................5 
Claims..............................................................................................................................................................................5 
 
Description of the device.................................................................................................................................................6 
Features ..........................................................................................................................................................................6 
Frontside..........................................................................................................................................................................6 
Backside .........................................................................................................................................................................7 
 
Installation...........................................................................................................................................................................7 
Installing the Lamp........................................................................................................................................................7 
 
Set Up and Operation .......................................................................................................................................................7 
Control Modes...............................................................................................................................................................8 
One Titan Strobe (Manual) ......................................................................................................................................8 
Multiple Titan Strobes (Master/Slave control).......................................................................................................8 
Multiple Titan Strobes (DMX Control) .....................................................................................................................9 
Fixture Linking...............................................................................................................................................................10 
Data Cabling...............................................................................................................................................................10 
Control Panel ...............................................................................................................................................................11 
Control Mode ..............................................................................................................................................................11 
DMX Addressing ..........................................................................................................................................................11 
Menu Overview...........................................................................................................................................................12 
Main Menu Options....................................................................................................................................................13 
1. Operation Modes ................................................................................................................................................13 
2. DMX Address (DMX Settings).............................................................................................................................13 
3. Channel Modes (DMX Settings)........................................................................................................................13 
4. DMX Error (DMX Settings) ...................................................................................................................................14 
5. Strobe Brightness (Manual Mode)....................................................................................................................14 
6. Strobe Frequency (Manual Mode) ..................................................................................................................14 
7. LED Master Dimmer (Manual Mode) ...............................................................................................................14 
8. LED Color Macros (Manual Mode) ..................................................................................................................14 
9. LED Color Switch/Flow Speed (Manual Mode) .............................................................................................14 
10. LED Color Switch/Color Flow Settings (Manual Mode) ..............................................................................15 
11. LED Strobe Frequency (Manual Mode) ........................................................................................................15 
DMX Channels .............................................................................................................................................................15 
3 Channels ................................................................................................................................................................15 
5 Channels ................................................................................................................................................................16 
9 Channels ................................................................................................................................................................17 
 
Maintenance....................................................................................................................................................................18 
Changing the Lamp...................................................................................................................................................18 
Replacing the Fuse.....................................................................................................................................................18 
 
Troubleshooting ...............................................................................................................................................................18 
No Light.........................................................................................................................................................................18 
No Response to DMX..................................................................................................................................................19 
 
Product Specifications....................................................................................................................................................20 
 
Dimensions........................................................................................................................................................................21 
 

Ordercode: 40297

Titan Strobe BLAZE

Warning

Unpacking Instructions

Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure

that all parts are present, and have been received in good condition. Notify the dealer immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be

returned to the factory, it is important that the fixture be returned in the original factory box and packing.

Your shipment includes:

Showtec Titan Strobe BLAZE

Pro power cable (1,5 m)

Mounting bracket

User manual

LED Expected Lifespan

LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration

of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular

optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is

significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower

operational temperatures. This may include climatic-environmental and the reduction of overall

projection intensity.

Safety Instructions

Every person involved with the installation, operation and maintenance of this device has to:

be qualified

follow the instructions of this manual

Before the initial start-up, please make sure that there is no damage caused by transportation.

Should there be any, consult your dealer and do not use the device.

To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to

follow the safety instructions and warning notes contained in this manual.

Please consider that damages caused by manual modifications to the device are not subject to

warranty.

This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

Ordercode: 40297

Titan Strobe BLAZE

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance of

this manual or any unauthorized modification to the device.

•Never let the power cord come into contact with other cables! Handle the power cord and all

connections with the mains with particular caution!

•Never remove warning or informative labels from the unit.

•Never use anything to cover the ground contact.

•Never run the device without lamp!

•Never ignite the lamp if the objective lens or any housing cover is open, as discharge lamps may

expose and emit a high ultraviolet radiation, which may cause burns.

•Never look directly into the light source.

•Never leave any cables lying around.

•Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord.

•Never strain the cable insert or the female part in the device. There must always be sufficient cable

going to the device. Otherwise, the cable will be damaged, which can cause serious damage.

•Never operate the stroboscope without protective shield! When the shield is cracked, replace it

before using the device again.

•Do not insert objects into air vents.

•Do not connect this device to a dimmer pack.

•Do not switch the device on and off in short intervals, as this would reduce the lamp’s life.

•Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).

•Do not shake the device. Avoid brute force when installing or operating the device.

•Only use device indoors, avoid contact with water or other liquids.

•Only operate the fixture after having checked that the housing is firmly closed and all screws are

tightly fastened.

•Only operate the device after having familiarized with its functions.

•Avoid flames and do not put close to flammable liquids or gases.

•Always replace the lamp, when it is damaged or deformed due to the heat.

•Always keep case closed while operating.

•Always allow free air space of at least 50 cm around the unit for ventilation.

•Always disconnect power from the mains, when device is not used, before cleaning or when

replacing lamp! Only handle the power cord by the plug. Never pull out the plug by tugging the

power cord.

•Make sure that the device is not exposed to extreme heat, moisture or dust.

•Make sure that the available voltage is not higher than stated on the rear panel.

•Make sure that the power cord is never crimped or damaged. Check the device and the power

cord from time to time.

•Make sure that the core diameter of extension cords and power cords is sufficient for the required

power consumption of the device.

•If device is dropped or struck, disconnect main power supply immediately. Have a qualified

engineer inspect for safety before operating.

•If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not

switch it on immediately. The arising condensation water might damage your device. Leave the

device switched off until it has reached room temperature.

•If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely

(preferably in the original packing material), and return it to your Showtec dealer for service.

•For adult use only. The fixture must be installed out of the reach of children. Never leave the unit

running unattended.

•For replacement use lamps of same type and rating only.

•Allow time to cool down, before replacing lamp.

•Keep away from direct insulation.

•This device is only allowed for an installation via the mounting bracket.

•The user is responsible for correct positioning and operating of the Titan Strobe. The manufacturer will

not accept liability for damages caused by the misuse or incorrect installation of this device.

•This device falls under protection class I. Therefore it is essential to connect the yellow/green

conductor to earth.

•The relative humidity must not exceed 50% with an ambient temperature of 35°C.

•Repairs, servicing and electric connection must be carried out by a qualified technician.

•WARRANTY: Till one year after date of purchase.

Ordercode: 40297

Titan Strobe BLAZE

Operating Determinations

•This device is not designed for permanent operation. Consistent operation breaks will ensure that the

device will serve you for a long time without defects.

•The minimum distance between light output and the illuminated surface must be bigger than 1

meter.

•To eliminate wear and improve lifespan, during periods of non-use, completely disconnect from

power via breaker or by unplugging.

•The maximum ambient temperature ta= 35°C must never be exceeded.

•The relative humidity must not exceed 50 % with an ambient temperature of 35°C.

•If this device is operated in any other way than the one described in this manual, the product may

suffer damages and the warranty becomes void.

•Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.

You endanger your own safety and the safety of others!

Rigging

Please follow the European and national guidelines concerning rigging, trussing and all

other safety issues.

Do not attempt the installation yourself !

Always let the installation be carried out by an authorized dealer !

Procedure:

•If the Titan Strobe is lowered from the ceiling or high joists, professional trussing systems have to be

used.

•Use a clamp to mount the Titan Strobe, with the mounting bracket, to the trussing system.

•The Titan Strobe must never be fixed swinging freely in the room.

•The installation must always be secured with a safety attachment, e.g. an appropriate safety net or

safety cable.

•When rigging, derigging or servicing the Titan Strobe, always make sure that the area below the

installation site is secured and that there are not any unauthorized people around.

The Titan Strobe BLAZE can be mounted to any kind of truss with a clamp.

Improper installation can cause serious injuries and/or damage of property!

Ordercode: 40297

Titan Strobe BLAZE

Connection with the mains

Connect the device to the mains with the power-plug.

Always check if the right color cable is connected to the right place.

International

EU Cable

UK Cable

US Cable

BROWN

RED

YELLOW/COPPER

PHASE

BLUE

BLACK

SILVER

NEUTRAL

YELLOW/GREEN

GREEN

PROTECTIVE GROUND

Make sure that the device is always properly connected to the earth!

Improper installation can cause serious injuries and/or damage of property!

Return Procedure

Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.

Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned

without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.

Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.

Be prepared to provide the model number, serial number and a brief description of the cause for the

return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the

customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace

product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.

Note: If you are given an RMA number, please include the following information on a piece of paper

inside the box:

01) Your name

02) Your address

03) Your phone number

04) A brief description of the symptoms

Claims

The client has the obligation to check the delivered goods immediately upon delivery for any short-

comings and/or visible defects, or perform this check after our announcement that the goods are at their

disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be

reported to the carrier upon receipt of merchandise.

It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is

damaged due to shipping. Transportation damage has to be reported to us within one day after receipt

of the delivery.

Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with

a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless

agreed otherwise in writing.

Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of

the invoice. After this period complaints will not be handled anymore.

Complaints will only then be considered if the client has so far complied with all parts of the agreement,

regardless of the agreement from which the obligation is resulting.

Ordercode: 40297

Titan Strobe BLAZE

Description of the device

Features

The Showtec Titan Strobe BLAZE is a perfect enhancement of the traditional Titan Strobe.

The RGB LEDs provide a colorful illumination of the reflector. The pre-programmed color macros are

divided into zones, in order to create color flows. The built-in lightning simulation, linear and random

strobe effects, blinder and single flash mode make the new Titan Strobe BLAZE the complete package for

all professional lighting operators.

•Input voltage: 240V AC, 50/60Hz

•Power consumption: 1800W

•Light source (strobe): Xenon 1500W tube

•Light source (blaze): 2 x RGB LED strip

•Light output: 120,000 lm

•Strobe (linear): 1-15Hz

•Strobe (blinder): 25Hz

•Control: Manual, Master/Slave, DMX-512/RDM

•DMX control: via standard DMX controller

•DMX channels: 3, 5, 9 channels

•Circuit breaker: 16A

•Color: Black

•Housing: Metal & flame-retardant plastic

•Connections: 3-pin/5-pin XLR IN/OUT, Pro power connector Blue IN

•IP rating: IP-20

•Dimensions: 495 x 160 x 265 mm (LxWxH)

•Weight: 5,9 kg

Frontside

Fig. 01

01) Mounting bracket with inclination screw

02) Adjustment screw

03) Lens

Ordercode: 40297

Titan Strobe BLAZE

Backside

Fig. 02

04) 16A circuit breaker (power switch ON/OFF)

05) 240V Pro power connector Blue IN

06) LCD display + LED indicators and control buttons

07) 3-pin DMX signal connector OUT

08) 3-pin DMX signal connector IN

09) Cooling fan

10) 5-pin DMX signal connector OUT

11) 5-pin DMX signal connector IN

Installation

Remove all packing materials from the Titan Strobe BLAZE. Check if all foam and plastic padding is

removed. Connect all cables.

Do not supply power before the whole system is set up and connected properly.

Always disconnect from electric mains power supply before cleaning or servicing.

Damages caused by non-observance are not subject to warranty.

Installing the Lamp

The Showtec Titan Strobe BLAZE uses the Showtec PX-1500 Xenon flashtube lamp, 1500W (ordercode

82690). Use only the appropriate lamp for your unit. Note that product versions, that use other lamps, may

be offered in the future. Check your product specification label for information.

Always disconnect from electric mains power supply before changing lamps.

The lamp has to be replaced when it is damaged or deformed due to the heat.

Do not install lamps of higher wattage! Lamps of higher wattage generate temperatures which the

device was not designed for.

Damages caused by non-observance are not subject to warranty.

DANGEROUS: Leave the device disconnected for 15 minutes, before opening.

Otherwise, you risk electrocution.

01) Disconnect from main power supply, and leave for 15 minutes.

02) Remove the glass cover. With the left hand, gently pull the lamp out of the spring, while pushing the

spring back with the right hand.

03) Remove the lamp. Read lamp instructions. Do not touch the lamp bulb glass. Oil on hands shortens

the lamp life. (If you touch the bulb glass, wipe off the glass with a clean, lint-free towel and rubbing

alcohol.) Hold the lamp with one hand and insert the lamp into the spring. Put the glass cover back.

Set Up and Operation

Follow the directions below, as they pertain to your preferred operation mode.

Before plugging the unit in, always make sure that the power supply matches the product specification

voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.

Connect the device to the main power supply.

Ordercode: 40297

Titan Strobe BLAZE

Control Modes

There are 3 modes:

•Manual

•Master/Slave

•DMX-512/RDM (3CH, 5CH, 9CH)

One Titan Strobe (Manual)

01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.

02) Plug the end of the electric mains power cord into a proper electric power supply socket.

03) When the Titan Strobe is not connected with a DMX cable, it functions as a stand-alone device.

Please see pages 14-15 for more information about Manual mode.

Multiple Titan Strobes (Master/Slave control)

01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.

02) Use a 3-pin/5-pin XLR cable to connect the Titan Strobe.

The pins:

01) Earth

02) Signal -

03) Signal +

03) Link the units as shown in fig. 03. Connect the first unit's DMX "out" socket with the second unit's "in"

socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.

You can use the same functions on the master device as described on pages 14-15 (Manual

mode). This means that you can set your desired operation mode on the master device and all

slave devices will react the same as the master device.

Multiple Titan Strobes (Master/Slave control)

Fig. 03

Ordercode: 40297

Titan Strobe BLAZE

Multiple Titan Strobes (DMX Control)

01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.

02) Always use a safety cable (ordercode 70140 / 70141).

03) Use a 3-pin/5-pin XLR cable to connect the Titan Strobes and other devices.

04) Link the units as shown in fig. 04. Connect the first unit's DMX "out" socket with the second unit's "in"

socket, using a DMX signal cable. Repeat this process to link the second, third, and fourth units.

05) Supply electric power: Plug electric mains power cords into each unit's Pro power socket, then plug

the other end of the mains power cord into proper electric power supply sockets, starting with the

first unit. Do not supply power before the whole system is set up and connected properly.

Multiple Titan Strobes DMX Set Up

Fig. 04

Note : Link all cables before connecting electric power

Inhaltsverzeichnis

Beliebte Arbeitsleuchte Handbücher anderer Marken

ANSMANN

ANSMANN POWERLIGHT 5.1 Bedienungsanleitung

RTRMAX

RTRMAX RTX1868 Bedienungsanleitung

FeinTech

FeinTech LAL00220 Bedienungsanleitung

Bunker Hill Security

Bunker Hill Security 64735 Bedienungsanleitung

Goobay

Goobay 30450 Bedienungsanleitung

REV Ritter

REV Ritter SPOT Bedienungsanleitung

Ignition

Ignition Stagepix Line 100 IP Bedienungsanleitung

SCANGRIP

SCANGRIP DUO CONNECT Bedienungsanleitung

Bosch

Bosch GLI 18 V Bedienungsanleitung

Bayco

Bayco SL-1514 Bedienungsanleitung

EUFAB

EUFAB SMD LED 8+1 Bedienungsanleitung

DeWalt

DeWalt DCL510 Bedienungsanleitung

PowerSmith

PowerSmith PWLD080T Bedienungsanleitung

MaxLite

MaxLite 73683 Bedienungsanleitung

Heitronic

Heitronic Trend 27867 Bedienungsanleitung

Monzana

Monzana Gore MZCL10 Bedienungsanleitung

EINHELL

EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung