Showhome ZW112 Bedienungsanleitung

FCC/IC

Federal CommunicationsCommission (FCC)Statement

FCC Caution: Anychangesormodi cationsnot expresslyapproved bythe partyresponsible for

compliancecould void the user’sauthoritytooperatethisequipment.

ThisdevicecomplieswithPart 15 of the FCC Rules.

Operation issubject tothe following two

conditions: (1)Thisdevicemaynot causeharmful interference, and (2)thisdevicemust accept any

interferencereceived, including interferencethat maycauseundesired operation.

NOTE: Thisequipment hasbeen tested and found tocomplywiththe limitsforaClass Bdigital device,

pursuant toPart 15 of the FCC Rules. Theselimitsaredesigned toprovide reasonable protection

against harmful interferencein aresidential installation.

Thisequipment generates, usesand can

radiateradio frequencyenergyand, if not installed and used in accordancewiththe instructions,

maycausharmful interferencetoradio communications.However, thereisno guarantee that

interferencewill not occurin aparticularinstallation.

If thisequipment doescauseharmful interference

toradio ortelevision reception, whichcan be determined byturning the equipment off and on,

the userisencouraged totrytocorrect the interferencebyone ormoreof the following measures:

Reorient orrelocatethe receiving antenna.Increasethe separation between the equipment and

receiver.Connect the equipment intoan outlet on acircuit different fromthat towhichthe receiver

isconnected.Consult the dealeroran experienced radio/TVtechnician forhelp.Thisequipment

should be installed and operated withminimumdistance20cmbetween the radiatorand yourbody.

ICCaution:

Doorwindow sensor

ThisdevicecomplieswithIndustryCanada licence-exempt RSS standard(s). Operation issubject

tothe following two conditions: (1)thisdevicemaynot causeinterference, and (2)thisdevicemust

accept anyinterference, including interferencethat maycauseundesired

operation of the device.

DECLARATIONDECONFORMITED'INDUSTRIECANADA

Ce périphérique a ététestéet reconnu conformeauxlimitesspéci éesdansRSS-210.

Son utilisation est soumiseauxdeuxconditionssuivantes:

(1)il ne doit pasprovoquerd'interférencesgênanteset

(2)il doit tolérerlesinterférencesre.ues, notamment cellessusceptiblesd'en perturberle fonctionnement.

Show HomeProductswarrantsthisproduct tobe free frommanufacturing defectsfor

W112 Motion Sensor

Motion Sensor

WARRANTY

Show HomeProductswarrantsthisproduct tobe free frommanufacturing defectsfor

aperiod of two years fromthe original dateof consumerpurchase. Thiswarrantyislimited

tothe repairorreplacement of thisproduct onlyand doesnot extend toconsequential or

incidental damage tootherproductsthat maybe used withthisproduct.

Thiswarrantyisin lieu of all otherwarranties, expressed orimplied. Somestatesdo not

allow limitationson how long an implied warrantylastsorpermit the exclusion orlimitation RISK OF FIRE

of incidental orconsequential damage, sothe abovelimitationsmaynot applytoyou. RISK OF ELECTRICALSHOCK

RISK OF BURNS

Thiswarrantygivesyou speci

crights, and you mayalsohaveotherrightswhichvaryfrom

CONTROLLING APPLIANCES:

statetostate. if the unit should provedefectivewithin the warrantyperiod. EXERCISE EXTREMECAUTIONWHENUSING Z-WAVE

DEVICES TO CONTROLAPPLIANCES. OPERATION

OF THEZ-WAVE DEVICEMAY BE INADIFFERENT

ROOMTHANTHECONTROLLEDAPPLIANCE, ALSO AN

UNINTENTIONALACTIVATIONMAY OCCUR IF THEWRONG

BUTTONONTHEREMOTEISPRESSED. Z-WAVE DEVICES

Model:ZW112 MAY AUTOMATICALLYBE POWEREDONDUETO TIMED

Powersupply: batteryCR123A, 3V. EVENTPROGRAMMING. DEPENDING UPONTHEAPPLI-

Signal (Frequency): 908.42 MHz. ANCE, THESE UNATTENDEDORUNINTENTIONALOP-

Operating Range: Up to100 feet line of sight

ERATIONSCOULD POSSIBLYRESULTINAHAZARDOUS

Operating Temp.: -15°C~60°C(5°F ~140°F) CONDITION. FORTHESE REASONS, WERECOMMEND

Wireless Controllerand the closest Z-Wave DO NOTRETURN THISPRODUCTTO THESTORE

receivermodule. THEFOLLOWING:

Speci cationssubject tochange without notice DO NOTUSE Z-WAVE DEVICES TO CONTROLELECTRIC

due tocontinuing product improvement HEATERSORANYOTHERAPPLIANCES WHICH MAY PRESENT

Website www.ishowlights.com AHAZARDOUSCONDITIONDUETO UNATTENDEDOR

UNINTENTIONALORAUTOMATICPOWERONCONTROL.

1.Do not attempt to disassemble the Motion Sensor,unless described in the user’s manual. There are no user serviceable parts.

2.Handle with Care –Avoid striking or shaking.Improper use or storage could damage the Motion Sensor. Modifying or tampering

the device or its internal components can cause a malfunction and void the Motion Sensor’s warranty.

3.Ifyou feel the Motion Sensor or anypart ofthe Choice Alert systemis not operating correctlyor as described, please contact us.

SPECIFICATIONS

WARNING

Importantsafeguards

The Motion Sensor is designed to be used indoor or outdoor. When mounted properlyit can monitor large or open areas such as

entrances, living rooms, familyrooms, driveways, backyards, walkways, workshops,etc. When the Sensor detects motion, it

will transmit a signal to the controller. The zone selection and setting on the Controller determine ifan alarmor an

alert sounds.

Preparing the Motion Sensor for Installation

1.The Motion Sensor consists of2 parts –The Sensor(Transmitter) and the wall mount. Before installing,remove the screwfrom

the batterydoor on the back ofthe Sensor. You’ll need to attach the batteryleads to CR123A 3V battery;Take care to note the

polaritymarkings. Replace the batterycover and secure screw.

2.Use the ball-head mount to mount the Sensor. The minimumspacing recommended is 5-6 ft, depending on where you want to

mount the Motion Sensor. Once the location is selected, before mounting you should performa manual test to con rmthe

Motion Sensor is within range ofController. Mount the ball-head joint to the location with screws provided. Once the ball-head

joint is mounted to the wall, slide the back ofthe sensor onto the ball-head joint. The mounting angle can be adjusted.

3.Erasing the Sensor froma Zone

Ifyou need to remove the Sensor froma Zone, the systemwill erase the entire Zone, so anyother Sensors will need to be put

back into that particular Zone.Step 1 - To erase a Zone, press and hold the Learn button on the Control Center. The unit will

beep once.Step 2 - While holding the Learn button, press and hold the Zone button to be erased. After ve seconds the Control

Center will sound two beeps and the Zone LED indicator will ﬂash twice.Step 3 - Release all buttons. The Zone has been erased.

and delaytime for next Trigger : 35 sec.

Note:

The Motion Sensor cannot be erased if: The sensor has been triggered for an Alert or alarm.

The Sensor must be reset when loss ofsignal fromthe Sensor to the Controller (such as lowbattery, or out ofrange).

The lowbatterystatus will be checked each hour and reported.

TO return your device to factory default:

Use certificated controller to remove device fromnetwork will reset it to factorydefault.

Please use this procedure onlyin the event that the network primarycontroller is missing or otherwise inoperable.

Adding to -Wave network

1) Install the battery. Visual indicator showstatus (blue flashing - device readyfor adding, LED off - device added),

2) Make sure the device is located within direct range ofthe Z-Wave controller.

3) Followthe instructions ofcertified controller to include a device fromdifferent manufactures into the Z-Wave network.

4) Once the controller is readyto include your device, triple click Tamper switch.

5) Motion Sensor will be detected and added in the Z-Wave network.

Removing from -Wave network

1) Followthe instructions for your Z-Wave certified controller to exclude a device fromthe Z-Wave network.

2) Once the controller is readyto Exclude your device,triple click Tamper switch to exclude it fromZ-Wave network.

Note:

Instruction

Note:

1. The association group supports five nodes and lifeline function.

2. This product can be operated in anyZ-Wave network with other Z-Wave certified devices from

other manufacturers. All non-batteryoperated nodes within the network will act as repeaters

regardless ofvendor to increase reliabilityofthe network.

Motion Sensor with

mounting bracket - 1pcs

Screw- 2pcs

Plastic anchors - 2pcs Top view

Ball-head joint - 1pcs

Detection pattern:

100 degree 10x10Mat 25°C

Side View

Packagecontent:

Inhaltsverzeichnis

Andere showhome Sicherheitssensor Handbücher

showhome

showhome ZW1101 Bedienungsanleitung

showhome

showhome ZW112 Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung