Showven SPARKULAR FALL Bedienungsanleitung

USER MANUAL

SPARKULAR®FALL

V2.1

2022/06/24

Showven Technologies Co., Ltd.

Thanks for choosing SPARKULAR®FALL, we wish it will sparks up your show.

Please read the following manual carefully before operating this product.

ΔSafety Instructions

\Unauthorized repair are prohibited, it may cause serious incident.

\Keep SPARKULAR®FALL dry and do NOT use in rain or snow.

\Make sure lid of feeding hopper are well covered when use SPARKULAR®FALL.

\Accidentally burning of consumable can only use sands to extinguish.

\Consumable should keep away from moisture and stored in a dry sealed environment.

\Check whether there is consumable aggregate in the output nozzle both before and after

each show, if any, please clean it up, or it will affect the firing effect, damage machine, even

cause serious incident.

\The SPARKULAR®FALL power supply cable maximum allowed cascade of 6pcs (BT04) / 3pcs

(BT05), exceed connecting may result in damage or even cause fire.

\For better heat dissipation, block the air intake and air outlet is prohibited.

\Cover the output nozzle of SPARKULAR®FALL is forbidden, inspect the machine before each

show, making sure no objects or material will block the output nozzle.

\Never touch the nozzle of SPARKULAR®FALL, danger of getting burnt.

\Never touch the sparks which shooting out from the nozzle.

\Make sure no staff, audience and flammable materials stays under the SPARKULAR®FALL.

Safety Distance

\Keep audience and flammable material at a minimum distance of 3m from SPARKULAR®

FALL.

\Make sure sparks shoot out from SPARKULAR® FALL can NOT touch any objects. And keep a

clearance with minimum 2m from the setting maximum effect length.

\Human, animal or flammable materials are not allowed to close to the underside area where

hanging SPARKULAR® FALL.

\In windy environment, increase the safety distance according to the wind direction and speed.

\The safety zone area shifts accordingly when machine installed in tilt position. Please increase

the safety distance in the direction which machine tilt.

\Sparks and consumables from the machine can lead to serious eye injury. Always wear safety

goggles when enter the safety zone.

ΔDescription

SPARKULAR®FALL is hanging special effects equipment for indoor/outdoor use to generate

dazzling silver “waterfall” sparks effects. According to different usage scenarios, operator can

self define various types of “spark curtain” effects vary from 2m to 7m by use of different types

of HC8200.

ΔStructure of SPARKULAR®FALL

1. Safety Loop

2. Clamp

3. Feeding Hopper Lid

4. Air Intake

5. DMX IN

6. DMX OUT

7. Power Switch

8. Fuse

9. Power IN

10. Power OUT

11. LCD Screen

12. Cooling Fan

Schematic diagram of the top fixing hole

ΔTechnical Specifications

\MODEL: BT04/BT05

\DIMENSION: 196× 208× 192mm

\WEIGHT: 6.0kg

\VOLTAGE: 220V(BT04)/110V(BT05), 50/60Hz

\WORK POWER: 500W

\EFFECT HEIGHT: 2-7m(according to HC8200 type)

\INTERFACE: 3-pin XLR, POWER IN/OUT

\CONTROL: DMX 2 channels, Wireless Remote

\ADAPTABLE TRUSS SIZE: 40-60mm

ΔOperation Panel

1. LED display area:

READY DMX FAULT HEAT

READY: Flash means machine is preparing, LED keeps on means ready to work

DMX: Flash means DMX signal is connected, light OFF means there is no DMX signal

FAULT: Light ON when error occurs

HEAT: Light ON when system is heating up

2. Control button area:

MENU Press to switch through menu, press and hold for 3s enter advanced menu

-: Parameters down

+: Parameters up

ENTER: Confirm and save parameters.

3. Bottom Indication Light

Off: Preheating not activated or machine is firing

Quick Flashing: Preheating

Long on: Preheated

Slow Flashing: Error warning

The indication light can be turned off in menu.

4. RFID area

Composite Ti with RFID card, swiping cards used to identify parameters and types of granules.

The RFID card is disposable, one card can only use one time.

ΔInterface

1. Main Interface

First line: Display DMX address is “1”

Second line: Display the present inner core temperature and the temperature progress bar;

displays remaining time is 7 minutes and 24 seconds.

2. Error information

3. Setting Menu

Press “MENU” to enter the Setting interface, press the “MENU” button to enter different

options until you return to the main interface

4. Advanced Menu

Press and hold “MENU” for 3s to enter the advanced setup interface, press MENU key to enter

different options, wait 3 seconds to return to the main interface

Error information

Explanation

E0 System IC

Systematic error

E2 Temp. Sensor

Temperature sensor is not connected or damage

E3 P Temp. Over

Chassis over-temperature

E4 Time Remain

Insufficient granules or remaining time, please swiping time card

E5 K Temp. Over

Heating chamber over-temperature

E6 Heat Fail

Heating failed

Options

Range

Default

Explanation

Set DMX Address

1-512

Set the DMX address, machine become a wireless host

and can send out DMX signal when its address is “1++”

Wireless Control

ON/OFF

OFF

Wireless function switch, you can match machine with

remote controller when at “ON” status

Manual Fountain

ON/OFF

OFF

Manual fountain switch, for testing purposes only

Fountain Height

1 / 6

1 is low level, 6 is high level

Options

Range

Default

Explanation

Set Temperature

480-620

580

Setup inner Core temperature

Auto Heat

ON/OFF

OFF

Auto preheat function switch after turn

on machine

Density

70-100

Adjust the sparks density

Mode Selection

Factory Mode

User Mode

Factory Mode is factory debugging

mode, User Mode is using mode

DMX Channel

Mode

2 / 4 / 2+3 DMX

Channel

2 DMX Channel

Don’t change. 4 DMX Channel and 2+3

DMX Channel are for special use.

Default

Parameter

Useless

Standby Switch

ON/OFF

OFF

When ON, the machine can firing only

when heating up was finished

Status LED

ON/OFF

Bottom indicate light ON/OFF

5. DMX mode

When using the DMX controller, SPARKULAR®FALL occupy 2 DMX channel

The First channel

Functions

0-15

Firing OFF

16-135

Low Level Fountain ON

136-255

High Level Fountain ON

The second channel

Functions

60-80

Clear Material

20-40

Emergency Stop

0-10

Pre-heat OFF (Disable in Auto-heat)

240-255

Pre-heat ON (Disable in Auto-heat)

ΔOperation Guide

1. Check output nozzle of SPARKULAR®FALL

Check carefully the output nozzle of each machine, make sure the output nozzle is in good

shape and there is no powder aggregate.

2. Fill SPARKULAR®FALL

a) Open powder bags and fill the feeding hopper. Hopper capacity of SPARKULAR®FALL is

280g.

b) Choose correct consumable according to the hanging height and safety distance.

c) Make sure the lid of hopper is locked tight after filling.

3. Install SPARKULAR®FALL

a) Vertical hanging installation is preferred for SPARKULAR®FALL. If need to installed

SPARKULAR®FALL in angles, please turn the Tip over to OFF status first, maximum firing

angle is 45 ° and can only be angled to the front side of the machine as below picture.

b) Make sure the machine is securely hanging on truss to avoid falling. An extra safety rope is

required for extra safety.

HC8200

Fall length (Low Level)

Fall length (High Level)

MEDIUM

LARGE

LARGE-Ⅰ

LARGE-Ⅱ

4. Connect Power / DMX cable

a) Connect a power cable to the POWER IN socket of SPARKULAR® FALL. Connect the other

end of power cable to the power source. Make sure power supply in consistent with the

rated voltage of the equipment, and the socket must well grounded.

b) If connect machine in sequence, please connect a power link cable to the POWER OUT of

previous machine, connect the other end of the power link cable to POWER IN of the next

machine.

c) The SPARKULAR® FALL power supply cable maximum allowed cascade of 6pcs (BT04) / 3pcs

(BT05). Do not connect exceed units to a single electrical circuit.

d) Power ON all SPARKULAR®FALL.

e) Assign DMX address for each unit of SPARKULAR®FALL. If use SHOWVEN host controller or

FXcommander to control the machine please allocate a unique DMX address for each unit

of machine.

If use remote controller to control SPARKULAR® FALL wirelessly, please set machine to

wireless ON status and match machine with remote controller. For DMX cable control please

execute below operations (f to h).

f) Connect a DMX cable to the DMX IN socket of first unit of SPARKULAR® FALL, connect the

male connector end of DMX cable to your DMX controller (FXcommander, HOST

CONTROLLER, light console etc).

g) Connect a DMX cable to the DMX OUT of previous machine, and the other end of to the

DMX IN of next machine. Connect all devices in series in this way.

h) Suggest to plug in a DMX terminator into the DMX OUT in last unit of machine to improve

signal reliability. Signal amplifier is required for long distance (>200m) DMX signal

transmission.

5. Activate SPARKULAR®FALL by swipe RFID card

a) Swipe an RFID card. Read the card as show below. SPARKULAR®FALL shows time remain if

read successfully.

b) SPARKULAR®FALL will report E4 when remaining time is less than 10 minutes.

c) Please note each RFID card come with 200g package HC8200 can increase single machine

20min working time, the maximum recharge time for SPARKULAR®FALL is 30min, when

time remain reached 30min, it can’t recharge anymore RFID card.

C N .00000001

6. Programming and Firing

a) Programming SPARKULAR®FALL, set the firing height, firing sequences etc.

b) Heating up machine, it takes around 5min. it various according to the voltage and

environment temperature.

c) Make sure the prescribed safety zone is clear.

d) Suggest to clear material before firing.

e) Firing. In order to prevent overheat in the heating chamber and protect machine, the

maximum continuous firing time for SPARKULAR®FALL is 30s.

f) The operator should always have a clear view of the device, so that he/she can stop the

show immediately when there is danger.

g) Clear material for SPARKULAR® FALL for 5s after show, clear material will remove the

remaining particles from heating chamber. For angled installation please elongate clear

material time.

7. Turn off and Clean up

a) Power off SPARKULAR®FALL, allow SPARKULAR®FALL to cool down.

b) Disconnect all POWER and DMX cables. Remove the machine from truss carefully.

c) Empty the remaining HC8200 in hopper, and store the remaining HC8200 in a dry sealed

bottle for next time use. Never touch the output nozzle of SPARKULAR® FALL when empty

the hopper. DANGER OF GET BURNT!

d) Clean the surroundings to remove powder residues.

ΔWireless Control Information

1. Wireless remote control mode:

When use wireless remote control, please unplug DMX cable connection on machine, set

Wireless Control at ON status, match the remote controller with machine, pull out the antenna

on remote controller.

1 ON

DMX address “1” ON

1 OFF

DMX address “1” OFF

2 ON

DMX address “3” ON

2 OFF

DMX address “3” OFF

3 ON

DMX address “5” ON

3 OFF

DMX address “5” OFF

SET

Match the machine with

remote

CLEAR

Clean material for 3

seconds

5 S

All firing 5s

15 S

All firing 15s

30 S

All firing 30s

OFF

All stop

NOTE:

a) When the indicator light becomes weak on the remote controller, please replace the

battery.

b) When the machine is occasionally not working, may be caused by interference, please press

the start button again.

c) Wireless control is easily influenced by interference, suggests to stay as close to machine as

possible when use remote controller, and machines cannot use metal shielding

3. Wireless host SPARKULAR®FALL mode (requires communication cables)

a) In occasion of strong interference, using the wireless host can avoid interference, ensure

stable control.

b) Set the first unit of SPARKULAR®FALL DMX address into “1++”, this machine address is “1”,

but it can also output DMX signal and turns into wireless host SPARKULAR®FALL.

c) Use communication cables to connect all SPARKULAR®FALL, the host SPARKULAR®FALL

will receive the signal from remote controller and transfer to all other SPARKULAR®FALL

via communication cable to realize stable signal transmission.

ΔMaintenance

a) Empty the feeding hopper before shipment of machine.

b) Empty the feeding hopper if long time not use, for high humidity environment we suggest

to empty feeding hopper after show.

c) Clear material both before and after the show.

d) Recommended to wash or replace the air intake filter every two months.

Andere Handbücher für SPARKULAR FALL

Dieses Handbuch passt für folgende Modelle

Andere Showven DJ-Equipment Handbücher

Showven

Showven Circle Flamer X-F1800 Bedienungsanleitung

Showven

Showven SPARKULAR PRO BT71 Bedienungsanleitung

Showven

Showven SPARKULAR FALL Bedienungsanleitung

Showven

Showven PyroSlave X16 Bedienungsanleitung

Showven

Showven SPARKULAR miniFALL BT14 Bedienungsanleitung

Showven

Showven uFIamer PF10 Bedienungsanleitung

Showven

Showven uFlamer PF10 Bedienungsanleitung

Showven

Showven X-F3600 Bedienungsanleitung

Showven

Showven SONICBOOM X Bedienungsanleitung

Showven

Showven Sparkular mini BT06 Bedienungsanleitung

Showven

Showven uFlamer Bedienungsanleitung

Showven

Showven SPARKULAR SPIN BT81 Bedienungsanleitung

Showven

Showven SONICBOOM PLUS SMOKEJET Bedienungsanleitung

Showven

Showven SPARKULAR TRIPLE BT51 Bedienungsanleitung

Showven

Showven SONICBOOM PLUS SMOKEJET Bedienungsanleitung

Showven

Showven SPARKULAR SPIN Bedienungsanleitung

Showven

Showven SE-SVBT85 Bedienungsanleitung

Showven

Showven uFlamer X1800 Bedienungsanleitung

Showven

Showven SPARKULAR PRO Bedienungsanleitung

Showven

Showven SPARKULAR miniFALL BT14 Bedienungsanleitung

Showven

Showven SPARKULAR II Bedienungsanleitung

Showven

Showven SE-SVBT72 Bedienungsanleitung

Showven

Showven SPARKULAR TRIPLE BT51 Bedienungsanleitung

Showven

Showven SPARKULAR WAVER Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung