Shure Advance MXA310 Bedienungsanleitung

MXA310

Table Array Microphone

Complete user guide for the MXA310. Includes installation instructions, specifications, best practices, command strings, and more.

Version: 5 (2020-B)

Shure Incorporated
2/55
Table of Contents
MXA310Table Array Microphone 4
Overview 4
General Description 4
Features 4
System Overview 5
System Planning and Gear Requirements 5
Setting up the Audio Network 6
System Use Cases 8
Telephone Conference with Shure MXW Audio Network 
Interface 9
Telephone Conference with Dante-enabled Audio Proces-
sor 11
Telephone Conference with Breakout Boxes and Audio 
Processor 12
Web Conferencing Software with Dante Virtual Soundcard1
5
Video Conference 17
Hardware and Installation 18
Hardware 18
LED Light Ring 19
Installing the Cable-Exit Plug 20
Permanent Table Installation 20
Power Over Ethernet (PoE) 23
Microphone Placement 23
Seating Scenarios 23
Software Installation, Management, and Security 26
Controlling Devices with Shure Designer Software 27
Accessing the Web Application 27
Web Application Browser Compatibility 27
Accessing the Web Application without the Discovery App2
8
Firmware Updates 28
Microphone Configuration 28
Control Software Overview 29
Microphone Configuration 29
Adding or Removing a Channel 30
Custom Presets 30
Templates 31
Adjusting Levels 31
Mute and Fader Groups 32
Identifying Channels 32
Device Identification 32
LED Light Ring 32
Parametric Equalizer (PEQ) 33
Reset 35
Low-cut Filter 36
Mute Buttons 36
AES67 37
Encryption 38
Mute Synchronization 38
Setting Up Mute Sync on the MXA310 and P300 39
Automix Channel 39
Automix Settings 40
Automix Modes 40
Using a Third-Party Control System 41
Networking and Dante 41
Digital Audio Networking 41
Switch and Cable Recommendations for Dante Network-
ing 41
Compatibility with Dante Domain Manager 41
QoS (Quality of Service) Settings 42
Dante Transmit Flows 42

Shure Incorporated
3/55
Networking Best Practices 42
Network Audio and Shure Control Data 43
Device IP Settings 43
Configuring IP Settings 43
Manually Assigning Static IP Address 43
Setting Latency 44
Operating the Control Software over Wi-Fi 44
Packet Bridge 44
IP Ports and Protocols 45
Troubleshooting 46
Important Product Information 47
Information to the user 47
What's in the Box 48
Optional Accessories 48
Specifications 48
Frequency Response 50

Shure Incorporated

4/55

•

MXA310

Table Array Microphone

Overview

General Description

The Microflex Advance table array is a premium networked tabletop microphone for AV conferencing environments, including

boardrooms, huddle rooms, and multi-purpose spaces. Revolutionary technology from the Shure DSP suite includes Steerable

Coverage , with selectable polar patterns on 4 independent channels to capture participant audio. The innovative new toroid

polar pattern delivers 360° coverage, while rejecting sound from directly above the microphone. Control the microphone with

Shure Designer software, or a browser-based web application. The microphone integrates seamlessly with Dante digital net-

worked audio and third-party preset controllers, including Crestron and AMX, to deliver a high-quality AV conferencing experi-

ence that appeals equally to integrators, consultants, and meeting participants.

Features

Configurable Coverage

Steerable Coverage delivers precise pick-up for up to 4 independent lobes

Shure DSP Suite provides fast-acting automatic mixing and channel equalization

Innovative toroid polar pattern delivers 360° coverage, while rejecting sound from directly above the microphone to reduce

noise caused by HVAC systems or video projectors.

Software Control

Shure Designer software provides comprehensive microphone and pattern control

With Designer, you can also design coverage with online and offline devices, and route audio between Shure devices

If Designer isn't available, use the browser-based web application to control the microphone

Network Connectivity

Four discrete audio channels and an additional automix channel are delivered over a single network cable

Dante digital audio coexists safely on the same network as IT and control data, or can be configured to use a dedicated

network

Control strings available for third-party preset controllers including Crestron and AMX

Professional Design

Sleek, low-profile industrial design blends with contemporary board rooms and meeting spaces

Configurable multi-colored LED light ring matches the environment, displays mute settings, and confirms coverage set-

tings

Available in white, black, and aluminum finishes

®™

™

Shure Incorporated

5/55

System Overview

①Dante audio, power, and control

A single network cable delivers 4 discrete audio channels from each microphone onto the Dante network, where they can

be routed to any Dante-compatible devices.

②Analog audio (microphone to network)

Analog equipment, such as a wireless microphone system or a gooseneck microphone on a podium, connects to the Dante

audio network through a Shure Network Interface (model ANI4IN) for a completely networked conferencing system.

③Far-end audio (network to loudspeakers)

Dante -enabled loudspeakers and amplifiers connect directly to a network switch. Analog loudspeakers and amplifiers con-

nect through a Shure Network Interface (model ANI4OUT), which converts Dante audio channels into analog signals, de-

livered through 4 discrete XLR or block connector outputs.

④Device control and Dante audio

A computer running Dante Controller and Shure Designer provides control over the following:

Control:

A computer connected to the network controls the microphone with Shure Designer software. You can remotely control

coverage, muting, LED behavior, gain, and network settings.

Audio:

Route audio with Dante Controller or Shure Designer software. Dante Virtual Soundcard enables audio monitoring

and recording directly on the computer.

™

™ ™

Shure Incorporated

6/55

System Planning and Gear Requirements

Setting up the Audio Network

Shure networked conferencing systems are comprised of Microflex Advance microphones and network interfaces, which oper-

ate entirely on a Dante network. Additional hardware, including network switches, computers, loudspeakers, and audio proces-

sors are described in the hardware component index.

Shure components shown in this diagram:

Microflex Advance Microphones

The MXA910 and MXA310 are equipped with Dante outputs, and connect directly to a network switch.

Audio Network Interfaces

The interfaces are used to connect analog devices such as loudspeakers and analog microphones to the network.

ANI4IN: Converts 4 analog signals (separate XLR and block connector models available) into Dante digital audio signals.

ANI4OUT: Converts 4 channels of Dante audio from the network into analog signals.

This diagram shows the entire signal path through a networked conference system. Signals from the near end and far

end are exchanged through an audio processor connected to a phone system, or through a computer connected to

the internet. Analog microphones connect to the network through the Shure ANI4IN, while loudspeakers connect

through the Shure ANI4OUT.

Shure Incorporated

7/55

This diagram shows Microflex Advance components in context, with two rooms communicating through video codecs.

Controlling Hardware and Audio Over the Network

Audio and hardware settings are managed through a computer connected to the same network.

Shure Hardware and Audio

Each Microflex Advance component has a web application which provides mixing and configuration tools to optimize sound

quality.

Expanded Control for Analog Devices

Analog devices that are connected to the network through a Shure network interface (ANI4IN/ANI4OUT) benefit from additional

remote control: Volume levels, equalization, and signal routing are managed through the web application. For example, adjust-

ing loudspeaker volume or muting a wired microphone, which would normally be done from the hardware, can now be con-

trolled remotely over the network.

Dante Signal Routing

You can manage signal routing with Dante Controller or Shure Designer software.

Shure Incorporated

8/55

•

System Use Cases

These use cases will help you understand how Shure devices fit in conference rooms, huddle rooms, and multipurpose

spaces.

Each diagram includes:

Signal flow and connections

Required devices

Power Over Ethernet and Hardware Requirements

All Shure devices included in these use cases require Power over Ethernet (PoE, class 0). Refer to the Dante and Network-

ing section for additional information on cable and network switch requirements.

Shure Incorporated

9/55

Telephone Conference with Shure MXW Audio Network Interface

①Array microphone to Shure MXWANI

Connect the microphone output to port 1 on the MXWANI with a network cable. Port 1 provides the necessary Power over

Ethernet (PoE).

②Computer to Shure MWXANI

Connect a computer to the ANI on port 2 or 3 with a network cable to provide control of the array microphone and other net-

worked components.

Shure Incorporated

10/55

③Shure ANI analog outputs to audio processor

Step 1: Route signals with Dante Controller software

Route the channels from the microphone (Dante transmitter) to the MXWANI channels (Dante receiver). This establishes the

discrete channels to deliver through the analog outputs.

Step 2: Connect the MXWANI outputs to the processing device inputs

Block connector outputs on the MXWANI send balanced audio signals to the inputs on the processing device, which provides

digital signal processing (such as acoustic echo cancellation).

④Connection to far end

Connect the audio processor to a VOIP server or telephone line to send and receive audio between the near end and far

end.

⑤Audio from far end to amplifier

Route the far-end audio through the audio processor output to an amplifier.

⑥Amplified audio signal to loudspeakers

Connect the loudspeakers to the amplifier to hear the audio from the far end.

Andere Handbücher für Advance MXA310

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Shure Mikrofon Handbücher

Shure

Shure 526T Series II Super Punch Bedienungsanleitung

Shure

Shure SM58LC Bedienungsanleitung

Shure

Shure SM11 Bedienungsanleitung

Shure

Shure W10BT Bedienungsanleitung

Shure

Shure 512 Headset Microphone Bedienungsanleitung

Shure

Shure PG48 Bedienungsanleitung

Shure

Shure Advance MXA310 Bedienungsanleitung

Shure

Shure SM7B Bedienungsanleitung

Shure

Shure BETA 98/S Bedienungsanleitung

Shure

Shure Microflex MX200 Series Bedienungsanleitung

Shure

Shure PGA 52 Bedienungsanleitung

Shure

Shure Microflex MX405 Bedienungsanleitung

Shure

Shure SV100 Bedienungsanleitung

Shure

Shure Microflex MX391BP Series Bedienungsanleitung

Shure

Shure WL93 Bedienungsanleitung

Shure

Shure Dispatcher 520SL Bedienungsanleitung

Shure

Shure Microflex MX392 Bedienungsanleitung

Shure

Shure PG ALTA PGA 57 Bedienungsanleitung

Shure

Shure ROSWELLITE KSM313 Bedienungsanleitung

Shure

Shure SM89 Bedienungsanleitung

Shure

Shure AXIENT DIGITAL ADX2FD Bedienungsanleitung

Shure

Shure SM91A Bedienungsanleitung

Shure

Shure PG48 Bedienungsanleitung

Shure

Shure PGA 98H Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

JLab

JLab GO TALK Bedienungsanleitung

Renkforce

Renkforce TY-109 Bedienungsanleitung

Trust

Trust 31008 Bedienungsanleitung