Shure WCM16 ISOMAX Bedienungsanleitung

1/6

WCM16 -- Headset Condenser Microphone

General Description

The Shure Model WCM16 head-worn electret condenser microphone is intended for wireless use by performers,

lecturers, and others who require the highest quality voice pickup with maximum mobility. Its wide frequency re

sponse, low RF susceptibility and reliable operation at temperature and humidity extremes make the WCM16 suit

able for virtually any vocal application. When used with the Shure Body-Pack Transmitters, the performance of the

WCM16 closely resembles the finest conventional vocal microphones.

Miniaturized active circuitry included in the cartridge assembly provides equalization that tailors the low-frequency

response to resemble the warm proximity effect of larger vocal microphones. Because of this low-end response, it

is not necessary to position the microphone directly in front of the mouth, thus avoiding much popping and breath

noise, even without the supplied foam pop screen.

The microphone's hypercardioid unidirectional pickup pattern provides maximum isolation from ambient noise and

from adjacent sound sources such as musical instruments, loudspeakers and other performers. This permits high

er gain-before-feedback without loss or masking of vocals.

FEATURES:

•Extra lightweight, adjustable headband stays secure and virtually disappears while being worn

•Response comparable to the finest conventional vocal microphones

• Hypercardioid polar pattern provides maximum isolation from vocalist's own instrument and those of other per

formers

•Uniform polar pattern at all frequencies for maximum gain before feedback

•High input clipping level eliminates overload distortion

•Supplied acoustic foam pop screen

•Reliable at temperature and humidity extremes

Wearing the Microphone Headset

1. Place the microphone on the user's head so that the large diameter band is horizontal across the back of the

head. The band may be completely hidden under the hair. The ends of the headband should fit comfortably in

front of the ears. Extend or retract the adjustable headband (see Figure 1) to achieve this result.

2. For maximum gain before feedback, carefully extend or retract the boom (see Figure 1) so that the microphone

grille (silver side) is within 40 mm (1-1/2 in.) of the left corner of the mouth. It may be necessary to bend the

Shure Incorporated

2/6

headband tube just in front of the left ear for optimum microphone positioning. A slight bend downward and/ or

away is usually sufficient.

Note: The headband tubing will not withstand repeated bending, so make this adjustment only once, if neces

sary.

3. If breath noise or popping is audible, install the supplied pop screen so that the red dot on the pop screen cor

responds to the location of the microphone grille.

Figure 1: PARTS OF THE WCM16 HEAD-WORN MICROPHONE

Positioning the Microphone Pickup

The hypercardioid unidirectional pickup pattern of the WCM16 has maximum rejection of unwanted sound sources

at about a 110° angle each way from the front axis of the microphone (see Figure 1). Directly to the rear of the mi

crophone (at 180°) there is as little as 6dB rejection-not much less pickup than at the front of the microphone (at

0°).

Sound sources that may cause feedback (such as monitor or P.A. speakers) or sound that you do not want to pick

up with the WCM16 (such as percussion instruments or other performers) should NOT be placed directly to the

rear of the microphone. It is better to adjust positioning so that unwanted sound sources are located at the 110°

maximum rejection points. Note that when wearing the headset the rear of the microphone points out towards the

wearer's left.

Shure Incorporated

3/6

Connecting to a Transmitter

The WCM16 is configured for direct connection to a Shure Body-Pack Transmitter, such as models T1, T1G, T11,

SC1, EC1, or LX1, using the attached cable.

Microphone Powering

The WCM16 is designed to be powered from the +5 Vdc source at microphone connector pin 2 of a Shure trans

mitter.

Specifications

(Measured using test circuit in Figure 4)

Type

Condenser (electret bias)

Frequency Response

50 to 18,000 Hz

Polar Pattern

Hypercardioid, uniform with frequency

Output Level (close-talked at 1,000 Hz)

Open Circuit Voltage -55.0 dBV (1.8 mV at 0.6 m) 1 Pascal=94 dB SPL

Maximum Sound Pressure Level

150 dB at 1%THD

Dynamic Range

121 dB

Output Noise

29 dB equivalent SPL, A-weighted

Shure Incorporated

4/6

Signal-to-Noise Ratio

65 dB at 94 dB SPL

Polarity

Microphone Positive sound pressure on diaphragm produces positive voltage on pins 3 and 4 with respect

to pin 1 (ground) of microphone output connector

Receiver--1/4

in. Output

Positive sound pressure on diaphragm produces positive voltage on tip of receiver 1/4" output

connector

Receiver--

XLR Output

Positive sound pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3

of the XLR output connector

Current Drain

0.35 mA

Recommended Operating Voltage

+5 V DC (positive on pin 2, negative on pin 1)

Environmental Conditions

Operating Temperature -18° to 60° C (0° to 140° F)

Storage Temperature -29° to 66° C (-20° to 150° F)

Relative Humidity 0 to 95%

Cable

1.5m (5 ft), small-diameter, shielded, with 4-pin mini connector

Case Finish (Microphone/Headband)

Matte black enamel

Shure Incorporated

5/6

Net Weight

36 g (1.27 oz.)

Figure 2: TYPICAL FREQUENCY RESPONSE

Figure 3: TYPICAL POLAR PATTERNS

Shure Incorporated

6/6

Figure 4: TEST CIRCUIT AND WIRING

Replacement Parts

4-Pin Mini Connector (TA4F/TQG) WA330

Windscreen 36A624

Andere Handbücher für WCM16 ISOMAX

Inhaltsverzeichnis

Andere Shure Mikrofon Handbücher

Shure

Shure PE548V Unidyne IV Bedienungsanleitung

Shure

Shure A400SM Bedienungsanleitung

Shure

Shure KSM9HS Bedienungsanleitung

Shure

Shure SM7 Bedienungsanleitung

Shure

Shure 592T Bedienungsanleitung

Shure

Shure KSM9 Bedienungsanleitung

Shure

Shure Microflex MX391 Series Bedienungsanleitung

Shure

Shure WH20 Bedienungsanleitung

Shure

Shure VP89L Bedienungsanleitung

Shure

Shure Beta 53 Bedienungsanleitung

Shure

Shure Beta 58 Bedienungsanleitung

Shure

Shure BETA 87C Bedienungsanleitung

Shure

Shure SM12A Bedienungsanleitung

Shure

Shure PE54 Unidyne III Bedienungsanleitung

Shure

Shure MX690 Bedienungsanleitung

Shure

Shure Beta 98A Bedienungsanleitung

Shure

Shure VP64 Bedienungsanleitung

Shure

Shure 565 UNISPHERE I Bedienungsanleitung

Shure

Shure PEISL-SP Bedienungsanleitung

Shure

Shure Unisphere B PE588B-CN Bedienungsanleitung

Shure

Shure PG27-USB Montageanleitung

Shure

Shure KSM44 Bedienungsanleitung

Shure

Shure Beta 53 Bedienungsanleitung

Shure

Shure W10BT Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

JLab

JLab GO TALK Bedienungsanleitung

Renkforce

Renkforce TY-109 Bedienungsanleitung

Trust

Trust 31008 Bedienungsanleitung