Shure WH30XLR Bedienungsanleitung

WH30XLR

ONLY

MODEL WH30 CONDENSER HEADSET MICROPHONE

Models WH30TQG and WH30XLR User Guide

2003, Shure Incorporated

27D3121 (Rev. 4) Printed in U.S.A.

English

INTRODUCTION

The Shure Model WH30 is a light yet rugged headset microphone. Designed

for vocalists and instrument-playing vocalists, the WH30 utilizes a high quality

electret-condenser cartridge suitable for all applications where mobility,

comfort, low microphone-visibility, and high sound quality are required.

Because of its cardioid (unidirectional) pickup pattern, the WH30 provides

isolation from extraneous sound sources and high gain-before-feedback.

The wireframe and gooseneck adjust to any head size and shape. An

integrated elastic CROAKIESheadband comfortably pads and secures the

headset. The WH30 is supplied with two snap-on windscreens, clothing clip,

storage bag and cable-management device.

FEATURES

•Smooth, natural frequency response comparable to professional condenser

hand-held microphones

•Lightweight wireframe and headband adjust for a secure, comfortable fit

•Extra-strong, small-diameter microphone cable resists breakage

•Moisture-proof cartridge housing

•Sturdy gooseneck-boom holds mic securely in place

•lsolation shock mount for reduced handling noise

•Matte black finish for low visibility

•High input clipping level helps avoid overload distortion

•Low self-noise and high sound pressure level capability

•Reliable at temperature and humidity extremes

MODEL VARIATIONS

•WH30TQG: For wireless use, the WH30TQG has a 1.5m (5 ft.) high-flex cable

and a mini TA4F connector for direct connection to Shure body pack transmit-

ters. (Note: for information about use with Shure W10BT or other transmitters

without a mini TA4F connector, contact Shure Customer Service).

•WH30XLR: For wired applications, the WH30XLR is supplied with a 1.5m (5

ft.) hi-flex cable and high quality mic preamplifier (RPM420) with a three pin

XLR connector. The RPM420 preamplifier requires phantom power from any

11 – 52 V source.

English

MICROPHONE PARTS

The WH30 consists of the following parts (see Figure 1).

1. Microphone Cartridge

and Windscreen

2. Microphone Boom

and Cartridge Housing

3. Isolation Shock Mount

4. Boom Hinge (rotates

as shown)

5. Cable

6. Elastic Headband

7. Wireframe

8. RPM420 Preamplifier

(WH30XLR only)

FIGURE 1. WH30 HEADSET MICROPHONE PARTS

COLLAPSIBLE MICROPHONE BOOM

The WH30 headset features a collapsible boom for shipment and storage.

Before wearing the headset, unfold the boom by rotating it away from the

wireframe until it snaps into place. Refold for storage or transportation.

WEARING THE HEADSET

Place the headset wireframe around your head so that the elastic headband

band lay horizontally across the back of your head and the ends of the

wireframe fit over your ears. You may position the elastic headband either

above or below the wireframe for the greatest comfort and stability. The blue

“SHURE” logo should face outward (see Figure 2).

English

FIGURE 2. WEARING THE

HEADSET FIGURE 3. POSITIONING THE

MICROPHONE

ADJUSTING THE HEADSET

•If the headset feels loose or uncomfortable, carefully bend the sides of the

wireframe to make it tighter or looser (see Figure 4A). The angle of the wire-

frame earpieces may also need adjustment (see Figure 4B).

•Adjust the tension of the elastic headband across the back of the head by slid-

ing it up or down the ends of the wireframe (see Figure 5).

FIGURE 4. ADJUSTING THE WIREFRAME

English

FIGURE 5. ELASTIC HEADBAND ADJUSTMENT

USING THE CABLE RETAINER AND CLOTHING CLIP

Use the cable retainer on the wire frame of the headset to position the

microphone cable as desired. The supplied spring-loaded clothing clip secures

the microphone cable to the user’s clothing to help avoid entanglement.

POSITIONING THE MICROPHONE

For maximum gain-before-feedback, position the microphone and boom so

that the microphone is within 13 mm (1/2 inch) of the right corner of your mouth

(see Figure 3). This will also help minimize breath noise or “popping”.

CONNECTING THE WH30 TO A SOUND SYSTEM

WIRELESS APPLICATIONS (WH30TQG)

1. Connect the mini TA4F connector from the WH30 to a wireless microphone

transmitter such as the Shure T1 bodypack transmitter.

2. See the user guide for your wireless transmitter and receiver system for ad-

justing gain and other parameters.

WIRED APPLICATIONS (WH30XLR)

Connect the output of the RPM420 preamplifier to an input channel of a

mixing or recording console. Most consoles will provide phantom power to the

RMP420 preamplifier. If phantom power is unavailable, use a separate

phantom power supply such as the Shure PS1A.

WASHING THE ELASTIC HEADBAND

When necessary, remove and wash the elastic headband according to these

steps.

1. Remove the microphone cable retainer from the wireframe.

2. Slide the elastic headband off the wireframe.

English

3. Wash the headband in mild, soapy water and rinse it in clean water.

4. Allow the headband to air-dry thoroughly.

5. Slide the headband around the wireframe to its original position. Reattach the

cable with the plastic retainer.

WASHING THE FOAM WINDSCREEN

The foam windscreen protects the WH30’s microphone-element from dirt

and moisture. When necessary, it can be removed and cleaned in a mild soapy

water solution. Important: Never clean the windscreen with any liquid solution

without first removing the windscreen from the microphone boom.

1. Hold the windscreen loosely by the plastic retaining ring at its base.

2. Gently pull the windscreen away from microphone. The plastic retaining ring

will expand to allow the windscreen to slip off the microphone. If necessary,

you can expand the ring manually with a small screwdriver as you pull the

windscreen.

3. Immerse the windscreen in mild soapy water and gently squeeze it several

times.

4. Rinse the windscreen in clean water and dry it with a clean cloth or paper tow-

el. Allow it to air-dry thoroughly.

5. When the windscreen is dry, slide it over the WH30 microphone until the re-

taining ring snaps into place.

CERTIFICATION

The WH30XLR conforms to European EMC Directive 89/336/EEC, and is eligible to bear the

CE marking. Meets applicable tests and performance criteria in European standard EN 55103

(1996) parts 1 and 2, for residential (E1) and light industrial (E2) environments. The WH30TQG

conforms to European EMC Directive 89/33/EEC, and is eligible to bear the CE marking. Meets

EMC require–ments as an ancillary device per EN 300 445 (1996)

REPLACEMENT PARTS

Cable Connector (for WH30TQG only) WA330. . . . . . . . . . . . . . . . . . . . . . . . . . .

Connector Belt Clip (for WH30XLR only) RK200BC. . . . . . . . . . . . . . . . . . . . . . .

Elastic Headband 80A505B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wireframe, Headband, Boom Hinge, Boom, Shock Mount,

Cartridge Housing and Cable RPM520. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preamplifier Assembly RPM420. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Black Windscreens (2) and Clothing Clip 90WP1371. . . . . . . . . . . . . . . . . . . . . .

English

SPECIFICATIONS WH30TQG WH30XLR

Type Condenser, electret bias Condenser, electret bias with

integrated preamplifier

Frequency Response 40 to 20,000 Hz (See Figure 6)

Polar Pattern Unidirectional (cardioid) (see Figure 7)

Output Impedance

(at 1kHz)

2400 ΩRated 150 Ω (actual) (Tolerates

loads as low as 150 Ω with

reduced clipping level)

Output Level

(at 1 kHz; 0 dB = 1 V/Pascal)

–55.5 dB 〈1.7 mV) –54.5 dB (1.9 mV)

Signal to noise ratio

(ref. A-weighted noise)

63.0 dB at 94 dB SPL (IEC 651)

Output Clipping Level

(at 1000 Hz)

–22 dBV (0.08 V) 2.5KΩLoad: -8 dBV (0.4V)

1 KΩLoad: -8 dBV (0.4V)

Maximum SPL 130 dB 2.5KΩLoad: 142 dB

1 KΩLoad: 142 dB

Dynamic Range (max. SPL to

A-weighted noise level)

99 dB 111 dB

Output Noise

(equivalent SPL)

31 dB (typical, A–weighted)

Recommended

Operating Voltage 5 VDC

(pin 2 to pins 3 and 4) 11–52 VDC Phantom power

Polarity Positive sound pressure on

diaphragm produces positive

voltage on pins 3 and 4 relative to

pin 1 (ground) on the mini TA4F

connector.

Positive sound pressure on the

diaphragm produces positive

voltage on pin 2 relative to pin 3 of

preamplifier output connector.

Environmental Conditions Operating Temperature –7_to 49_C (20_to 120_F). .

Storage Temperature –29_to 74_C (–20_to 165_F). . .

Humidity: 0 to 95 % (operating or storage). . . . . . . . . . . . .

Cable 3.05 m (10 ft.) two-conductor, shielded

Cable Connector mini TA4F XLR

Net Weight Headset: 65 g (2.3 oz) Headset and cord: 60 g (2.1 oz)

Preamplifier: 99 g (3.5 oz)

English

FREQUENCY IN Hz

RELATIVE RESPONSE IN dB

1 cm. (0.4 in.)

61 cm. (24 in.)

FIGURE 6. WH30: TYPICAL FREQUENCY RESPONSE

FIGURE 7. WH30: TYPICAL POLAR PATTERNS

English

WIRING DIAGRAMS

MODEL WH30XLR

MODEL WH30TQG

CARTRIDGE

RED (to drain) (DC bias)

BLACK (to source) (audio)

SHIELD

BLACK (to source) (audio)

RED (to drain) (DC bias) PREAMP

XLR CONNECTOR

TA4F CONNECTOR

FILTER

FET

MIC

ELEMENT

MIC

ELEMENT

FIGURE 8. WIRING DIAGRAMS

Trademark Notices: The stylized Shure logo and the word “Shure” are registered

trademarks of Shure Incorporated in the United States. “Teflon” is a registered

trademark of E.I. duPont de Nemours and Company in the United States.

“Croakies” is a registered trademark of Life-Link International, Inc.

SHURE Incorporated Web Address: http://www.shure.com

5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: 800-257-4873 Fax: 847-600-1212

In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414

In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055

Elsewhere, Phone: 847-600-2000 Fax: 847-600-6446

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Shure Mikrofon Handbücher

Shure

Shure UNIDYNE II 55S Bedienungsanleitung

Shure

Shure PGA 98D Bedienungsanleitung

Shure

Shure 550L Bedienungsanleitung

Shure

Shure VP88 Bedienungsanleitung

Shure

Shure Microflex MX418D Bedienungsanleitung

Shure

Shure PE65 Series Bedienungsanleitung

Shure

Shure Microflex MX391 Series Bedienungsanleitung

Shure

Shure SM35 Bedienungsanleitung

Shure

Shure WL93 Bedienungsanleitung

Shure

Shure Microflex Advance MXA910 Bedienungsanleitung

Shure

Shure 33-44 Series Bedienungsanleitung

Shure

Shure SM58 Bedienungsanleitung

Shure

Shure UNI- DYNE B 15SB-GI8 Bedienungsanleitung

Shure

Shure PE25L Series Bedienungsanleitung

Shure

Shure Microflex MX395 Bedienungsanleitung

Shure

Shure 526T Series II Super Punch Bedienungsanleitung

Shure

Shure WL93 Bedienungsanleitung

Shure

Shure TK-3360 Bedienungsanleitung

Shure

Shure Beta 53 Bedienungsanleitung

Shure

Shure Microflex MX415DUAL Bedienungsanleitung

Shure

Shure SM57 Bedienungsanleitung

Shure

Shure UNISPHERE 586A Bedienungsanleitung

Shure

Shure Beta 98HC Bedienungsanleitung

Shure

Shure MX690 Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

JLab

JLab GO TALK Bedienungsanleitung

Renkforce

Renkforce TY-109 Bedienungsanleitung

Trust

Trust 31008 Bedienungsanleitung