Shuttle HOT-617 Bedienungsanleitung

User's Manual 1

HOT-617

Pentium™Pro processor

Based PCI MAIN BOARD

User's Manual

User's Manual 2

NOTICE

Manual Ver 1.0

All information, documentation, and specifications contained in this manual are subject to change without

prior notification by the manufacturer.

The author assumes no responsibility for any errors or omissions which may appear in this document nor

does it make a commitment to update the information contained herein.

TRADEMARKS

Intel is a registered trademark of Intel Corporation

Pentium™ Pro Processor is a registered trademark of Intel Corporation

PC/AT is a registered trademark of International Business Machine Corporation.

PS/2 is a registered trademark of IBM Corporation.

All other brand and product names referred to in this manual are trademarks or registered trademarks of

their respective holders.

FCC Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used properly, in

strict accordance with the manufacturer’s instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help and for additional suggestions.

The user may find the following booklet prepared by the Federal Communications Commission helpful “How to Identify

and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office.

Washington, DC 20402, Stock 004-000-00345-4

FCC Warning

The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user’s

authority to operate this equipment.

Note : In order for an installation of this product to maintain compliance with the limits for a Class B device, shielded

cables and power cord must be used.

CE Notice:

Following standards were applied to this product, in order to achieve compliance

with the electromagnetic compatibility:

- Immunity in accordance with EN 50082-1: 1992

- Emmitions in accordance with EN 55022: 1987 Class B.

User's Manual 3

TABLE OF CONTENTS

PREFACE ....................................................................................4

CHAPTER 1 INTRODUCTION .............................................................5

Specification.........................................................................................................................5

CHAPTER 2 HARDWARE CONFIGURATION ........................................... 7

Jumpers.................................................................................................................................7

CPU Clock Speed Selection................................................................................................8

Onboard Voltage Regulators...............................................................................................9

Onboard Voltage Regulatro VIO Output - JP9, JP10........................................................9

Clear CMOS - JP8...............................................................................................................9

Flash EEPROM Jumper - JP1...........................................................................................10

Connectors & Sockets........................................................................................................11

CHAPTER 3 MEMORYCONFIGURATION ............................................ 12

CHAPTER 4 AWARD BIOS SETUP ................................................. 13

The Main Menu.................................................................................................................14

Standard CMOS Setup......................................................................................................16

BIOS Features Setup.........................................................................................................18

Chipset Features Setup......................................................................................................20

Power Management Setup.................................................................................................24

PCI Configuration Setup...................................................................................................26

Integrated Peripherals........................................................................................................28

Password Setting................................................................................................................30

User's Manual 4

HOT-617 mainboard is a highly integrated IBM PC/AT compatible system board. The design

will accept Intel Pentium Pro processors with size of 256KB and 512KB cache. The memory

subsystem is designed to support up to 512 MB of EDO, Burst EDO, and Fast Page Mode

DRAM Module in standard 72-pin SIMM socket. A type 8 Pentium processor socket

provides access to future processor enhancements.

HOT-617 mainboard provides a new level of I/O integration. Intel's 82440FX PCIset chipset

provides increased integration and improved performance over other chipset designs. The

82440FX PCIset chipset provides an integrated Bus Mastering IDE controller with two high

performance IDE interfaces for up to four IDE devices.

The onboard Giga I/O controller provides the advanced and standard PC I/O functions:

keyboard controller, floppy interface, Real Time Clock, two FIFO serial ports, an IrDA device

port and a SPP/EPP/ECP capable parallel port.

Up to five PCI local bus slots provide a high bandwidth data path for data-movement

intensive functions such as graphics, and up to three ISA slots complete the I/O function.

The HOT-617 mainboard provides the foundation for cost effective, high performance, highly

expandable platforms, which deliver the latest in Pentium Pro processor and I/O standard.

Preface

User's Manual 5

Chapter1 Introduction

CPU

Supports 180MHz or 200MHz Pentium™ Pro CPU on a ZIF socket 8.

Note : HOT-617 main board doesn't support older Pentium ™Pro processors without

VID(Voltage Identification) supported

Chipset

Features Intel's i440FX PCIset with ITE Giga I/O subsystems.

Memory

Supports four 72-pin SIMMs of 4MB, 8MB, 16MB, 32MB, 64MB, and

128MB to form a memory size from 8MB to 512MB.

Supports Fast Page Mode (FPM), Extended Data Output (EDO), and

Burst Extended Data Output (BEDO) DRAM Module.

Supports Error Checking and Correcting (ECC) function, when using

parity DRAM modules can detect and correct 1 bit memory errors.

Cache Memory

Support Pentium™ Pro's built-in 256KB or 512KB level 2 cache so that

no external cache chips are required.

Power Management Function

Provides four power management modes : Full on, Doze, Standby, and

Suspend.

Supports Microsoft APM 1.2.

Provides EPMI (External Power Management Interrupt) pin

Specification

User's Manual 6

Expansions

32-bit PCI bus slot x 5

16-bit ISA bus slot x 3

2-channel PCI IDE port support up to 4 IDE devices.

- PIO Mode 4, DMA Mode 2 transfers up to 22 MB/sec

- Integrated 8 x 32-bit buffer for PCI IDE burst transfers

One floppy port

One parallel port

- SupportsSPP (PS/2 compatible bidirectional Parallel Port),

EPP (Enhanced Parallel Port), and

ECP (Extended Capabilities Port) high performance parallel port.

Two serial ports

- Supports 16C550 compatible UARTS.

- Supports IrDA (Infrared) communication.

One PS/2 mouse mini DIN connector (option)

Two USB (Universal Serial Bus) ports

System BIOS

Award 4.51PG Pentium Pro™ PCI BIOS

Support DMI (Desktop Management Interface)

Board Design

Dimension 220mm x 280mm

User's Manual 7

Jumpers

Chapter2Hardware Configuration

User's Manual 8

CPU Clock Speed Selection

HOT-617 mainboard features a clock generator to provide adjustable System Bus Clocks

and PCI Bus Clocks. JP3 is a 6-pin jumper that determine the System Bus Clock from 50

MHz to 66 MHz and PCI Bus Clock from 25MHz to 33MHz.

HOT-617 mainboard also provides Jumper JP4 to figure the CPU Core Clock multiplier.

By inserting or removing jumper caps on JP4, the user can change theSystem Bus

Clock/CPU Core Clockratio from 1 : 2 to 1 : 4.

System Bus Clock & PCI Bus Clock Selection - JP3

System Bus Clock 50 MHz 60 MHz 66 MHz

PCI Bus Clock 25 MHz 30 MHz 33 MHz

JP3

PentiumProProcessorFrequencyReference Table

PentiumProSystemBus

Clock-JP3Multiplier-JP4Remark

180MHz60MHz3X

200MHz66MHz3XFactoryDefault

CPU Frequency Multiplier Selection - JP4

Frequency

Multiplier 2 X 2.5 X 3 X 3.5 X 4 X

JP4

User's Manual 9

Onboard Voltage Regulators

HOT-617 mainboard is designed with onboard voltage regulator to

provide power for Pentium™ Pro processor, external VRM wasn't

needed.

Pentium™ Pro processors required different voltages. Current

processors (marked "Pentium™ Pro") support VID and will

automatically adjust the voltage regulator so that no jumper

settings are required and provided on

HOT-617.

HOT-617 doesn't support older Pentium Pro processors

without VID supported .

Onboard Voltage Regulator VIO Output- JP9, JP10

HOT-617 mainboard is designed an additional feature to adjust VIO voltage which

provide power to CPU and chipsets.

VIO voltages adjustable from 3.1V to 3.8 V by jumpers JP9 and JP10. Normally, VIO

adjust by the user is not required. Factory default is 3.3V.

VioOutputSelection -JP,JP10

Voltage Vio 3.1 V 3.2 V 3.3 V Default 3.4 V 3.5 V 3.8 V

JP9,JP10

This jumper clears the CMOS data stored in the ITE 8680 Giga I/O chip. To clear the

CMOS data please follow list steps:

1) Turn off the PC,

2) Remove the jumper cap from Pin 1-2,

3) Insert the jumper cap on Pin 2-3 for a while

4) Remove the jumper cap from Pin 2-3,

5) Reinsert the jumper cap on Pin 1-2,

6) Turn on the PC.

Clear CMOS - JP8

Selection JP8

Normal Operation

Clear CMOS

User's Manual 10

Flash EEPROM Jumper - JP1

HOT-617 mainboard supports two types of flash EEPROM, 5 volt and 12 volt. By

setting up jumper JP1, you can update both types of flash EEPROM with new system

BIOS files as they come available.

Normal, JP1 was set by factory, the user need not to change.

JP1 Pin 2-3 Close for 5V

JP1 Pin 1-2 Close for 12V

BIOS UPGRADES

Flash memory makes distributing BIOS upgrades easy. A new version of the BIOS can

be installed from a diskette.

Please note the following when making the BIOS updates.

** Flash utility can't work under protected/virtual mode. Memory manager

like QEMM.386, EMM386should not be loaded. (or Simply bypass all

config.sysand autoexec.baton system boot up.

** Flash utility supports both 5V and 12V Flash EEPROM.

Inhaltsverzeichnis

Andere Shuttle Hauptplatine Handbücher

Shuttle

Shuttle FV25 Bedienungsanleitung

Shuttle

Shuttle AN35 Ultra Bedienungsanleitung

Shuttle

Shuttle FN41V3 Bedienungsanleitung

Shuttle

Shuttle AV18 Bedienungsanleitung

Shuttle

Shuttle Spacewalker AV40 Bedienungsanleitung

Shuttle

Shuttle FN85 Bedienungsanleitung

Shuttle

Shuttle HOT-433 Bedienungsanleitung

Shuttle

Shuttle HOT-641/P Bedienungsanleitung

Shuttle

Shuttle AB48 Bedienungsanleitung

Shuttle

Shuttle MZ11 Bedienungsanleitung

Shuttle

Shuttle Spacewalker AE14 Bedienungsanleitung

Shuttle

Shuttle FB77 Bedienungsanleitung

Shuttle

Shuttle FB65 Bedienungsanleitung

Shuttle

Shuttle HOT-559 Bedienungsanleitung

Shuttle

Shuttle AN50R Bedienungsanleitung

Shuttle

Shuttle HOT-603 Bedienungsanleitung

Shuttle

Shuttle HOT-591 Bedienungsanleitung

Shuttle

Shuttle FB51 Bedienungsanleitung

Shuttle

Shuttle SH610R4 Series Bedienungsanleitung

Shuttle

Shuttle Spacewalker AK32 Bedienungsanleitung

Shuttle

Shuttle AN51R Bedienungsanleitung

Shuttle

Shuttle FS58 Bedienungsanleitung

Shuttle

Shuttle FN45 Bedienungsanleitung

Shuttle

Shuttle FS56 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung