SI FlexGlass In-Wall Gen 2 Bedienungsanleitung
Owner’s Manual
FlexGlass In-Wall
FlexGlass In-Wall Gen 2 2
www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C
FlexGlass Screen Material (Ships in separate package)
2X Horizontal Frame
2X Vertical Frame
3X Flat Horizontal Trim
4X Flat Vertical Trim
1X 45º Horizontal Trim
Frame and Trim
FlexGlass In-Wall Gen 2 3
www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C
Hardware Box contents
8 x Corner Brackets
Gloves
Wood Screws
9/64 Ball Point Hex Driver
Shims
11/32 Nut Driver
8-32 Hex Nuts
Driver Bit For
Wood Screws
1/8 Hex Key
FlexGlass In-Wall Gen 2 4
www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C
Pre-Assemble The Frame
1) Insert 8 Corner brackets into the slots in the shorter vertical frame pieces.
2) Make sure that the viewing sides stickers and posts in the tensioners are pointing the same
direction a, then slide the corner brackets into the horizontal frame pieces, make sure all corners
align well, and lock all set screws to secure corner brackets.
Tighten all Set Screws in corner brackets
Tensioners Facing the same way
FlexGlass In-Wall Gen 2 5
www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C
Install the Frame in the wall
3) Make sure the rough opening in the wall has been prepared such that it is 1/4’’ to 1/2’’ larger than
the assembled frame.
4) Slide the frame into the rough opening and secure the bottom frame piece to the sill with the wood
screws. Make sure the viewing side stickers and the posts in the tensioners are all facing the
audience.
FlexGlass In-Wall Gen 2 6
www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C
5) Use the shims to fill the gaps around the sides and top of the frame. Then Secure the side and top
frame pieces to the rough opening with the wood screws drilled directly through the shims. Make sure
the frame components are secured to the wall and straight before proceeding.
6) Once the frame is secured to the rough opening around all four sides, then bend the shims to snap
off the excess material that sticks out of the back and front of the opening.
Install the Flex Glass Material in the Frame
7) Unroll the Flex Glass material onto a clean floor keeping the packaging foam in between the ma-
terial and the floor.
Note: Shiny Side of FlexGlass faces the projector and Matte side faces the audience.
FlexGlass In-Wall Gen 2 7
www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C
8) Spread out the tensioners approximately evenly spaced along the top and bottom frame. Then
carefully lift the screen material up into the frame and onto the threaded posts on the tensioners.
Secure the screen material to the tensioners with the hex nuts. Make sure the projection side is
facing the projector location.
9) Continue to secure the screen material to all the tensioners with the hex nuts.
FlexGlass In-Wall Gen 2 8
www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C
Tension the FlexGlass Material in the Frame
10) Tension the FlexGlass by turning the screws on the tensioners as shown below.
11) Continue applying tension to the screen all the way around until the FlexGlass is tight and flat.
You will need to make at least 2 passes around the screen to achieve proper tightness. If the frame
starts to bend then release tension until it goes straight. The frame must be straight to finish
installing the trim in following steps.
FlexGlass In-Wall Gen 2 9
www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C
Attach the Trim
12) Snap in the vertical trim pieces first as shown.
13) Snap in the remaining trim pieces. Note that the single 45º trim piece goes on the projector side
along the bottom if the projector is mounted on the floor or along the top if the projector is mounted
on the ceiling.
Audience
45º trim to
accommodate
ultra short throw
projectors.
FlexGlass In-Wall Gen 2 10
www.screeninnovations.com Installation Questions: 512-832-6939 FGIWG2-C
LIMITED ONE YEAR WARRANTY
ON SCREEN INNOVATIONS PRODUCTS
Screen Innovations warrants its products to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original
purchaser provided they are properly operated according to Screen Innovations’ instructions and
are not damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental
damage, or which has been tampered with or repaired by a person other than authorized Screen
Innovations personnel.
Screen Innovations’ sole obligation under this warranty shall be to repair or to replace (at Screen
Innovations’ option) the defective part of the merchandise. Returns for service should be made to
your Screen Innovations’ dealer. If it is necessary for the dealer to return the screen or part to
Screen Innovations, transportation expenses to and from Screen Innovations are payable by the
purchaser and Screen Innovations is not responsible for damage in shipment. To protect yourself
against damage or loss in transit, insure the product and prepay all transportation expenses.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY. Any implied
warranties of fitness for use, or merchantability, that may be mandated by statute or rule of law are
limited to the one (1) year warranty period. This warranty gives you specific legal rights, and you
may also have other rights, which vary from state-to-state. NO LIABILITY IS ASSUMED FOR
EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF
EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY
NATURE.
In the event that there is a defect in materials or workmanship of a Screen Innovations product, you
may contact our Sales Partners at 9715-B Burnet Road Suite 400, Austin, TX 78758, (512) 832-
6939.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND SCREEN INNOVATIONS SHALL
NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN
ACCORDANCE WITH SCREEN INNOVATIONS’ WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
Inhaltsverzeichnis
Andere SI Projektorzubehör Handbücher
