SICK GRSE18 4 Series Bedienungsanleitung

OPERATING INSTRUCTION

GRSE18

Round photoelectric sensors

BETRIEBSANLEITUNG

GRSE18

Rund-Lichtschranken

Described product

GR18

GRSE18

Manufacturer

SICK AG

Erwin-Sick-Str. 1

79183 Waldkirch

Germany

Production location

Legal information

This work is protected by copyright. Any rights derived from the copyright shall be

reserved for SICK AG. Reproduction of this document or parts of this document is

only permissible within the limits of the legal determination of Copyright Law. Any modi‐

fication, abridgment or translation of this document is prohibited without the express

written permission of SICK AG.

The trademarks stated in this document are the property of their respective owner.

Original document

This document is an original document of SICK AG.

2006/42/EC

SAFETY

8016954.1ABM / 2020-12-21 | SICK

Subject to change without notice 3

Contents

1 General safety notes......................................................................... 5

2 Notes on UL approval........................................................................ 5

3 Correct use......................................................................................... 5

4 Commissioning.................................................................................. 5

4.1 Check the application conditions............................................................ 5

4.2 Mounting................................................................................................... 6

4.3 Electronics................................................................................................. 7

4.4 Alignment.................................................................................................. 8

4.5 Adjustment................................................................................................ 8

5 Additional functions.......................................................................... 9

6 Troubleshooting................................................................................. 9

7 Disassembly and disposal............................................................... 10

8 Maintenance...................................................................................... 10

9 Technical specifications................................................................... 10

9.1 Dimensional drawings.............................................................................. 11

CONTENTS

48016954.1ABM / 2020-12-21 | SICK

Subject to change without notice

1 General safety notes

■Read the operating instructions before commissioning.

■

Connection, mounting, and configuration may only be performed by trained

specialists.

■

2006/42/EC

SAFETY

Not a safety component in accordance with the EU Machinery Directive.

■

Do not install the sensor at locations that are exposed to direct sunlight

or other weather influences, unless this is expressly permitted in the operating

instructions.

■These operating instructions contain information required during the life cycle of

the sensor.

2 Notes on UL approval

UL: Only for use in applications in accordance with NFPA 79. These devices shall be

protected by a 1 A fuse suitable for 30 V DC.

Adapters listed by UL with connection cables are available.

Enclosure type 1.

3 Correct use

The GRSE18 is an opto-electronic through-beam photoelectric sensor (referred to as

"sensor" in the following) for the optical, non-contact detection of objects, animals, and

persons. A sender (GRS) and a receiver (GRE) are required for operation. If the product

is used for any other purpose or modified in any way, any warranty claim against SICK

AG shall become void.

4 Commissioning

4.1 Check the application conditions

Observe the application conditions: Adjust the distance between the sender and the

receiver according to the corresponding diagram (x = sensing range, y = operating

reserve).

If several through-beam photoelectric sensors which are installed next to one another

are to be used, we recommend swapping the sender/receiver arrangement at every

second through-beam photoelectric sensor and ensuring that there is sufficient dis‐

tance between the through-beam photoelectric sensors. By doing this, mutual interfer‐

ence can be prevented.

GENERAL SAFETY NOTES 1

8016954.1ABM / 2020-12-21 | SICK

Subject to change without notice 5

(feet)

(13.12)

(26.25)

(39.37)

(52.49)

100

1000

Operating reserve

Distance in m (feet)

Figure 1: H

Receiver

Sender

Receiver

Figure 2: I

4.2 Mounting

Mount sensors (sender and receiver) using suitable mounting brackets (see the SICK

range of accessories). Align the sender and receiver with each other [K].

Observe the maximum permissible tightening torque of the sensor of 2.0 Nm for

metal/0.9 Nm for plastic [K].

4 COMMISSIONING

68016954.1ABM / 2020-12-21 | SICK

Subject to change without notice

Figure: K: GRSE18-x24x7

Figure: K: GRSE18-x24x2

4.3 Electronics

The sensors must be connected in a voltage-free state (VS = 0 V). The information in the

graphics [B] must be observed, depending on the type of connection:

– Male connector connection: pin assignment

– Cable: core color

+ (L+)

- (M)

Test

brn

blu

blk

not connected

wht

+ (L+)

brn

blk

wht

- (M)

blu

Figure 3: B: GRSE18-x11xx

1Sender

2Receiver

Only apply voltage/switch on the power supply (VS > 0 V) once all electrical connections

have been completed. The green LED indicator lights up on the sensor.

Explanations of the connection diagram (Graphic B):

Switching outputs Q and /Q (according to Graphic B):

GRSE18-P (PNP: load -> M)

GRSE18-N (NPN: load -> L+)

COMMISSIONING 4

8016954.1ABM / 2020-12-21 | SICK

Subject to change without notice 7

Test = test input (see Additional functions)

4.4 Alignment

Align the sender (GRS18) with the receiver (GRE18). Select the position so that the red

emitted light beam hits the receiver. Tip: Use white paper or a reflector as an alignment

aid. The sender must have a clear view of the receiver, with no object in the path of

the beam [see figure 4]. You must ensure that the optical openings (front screen) of the

sensors are completely clear.

Figure 4: Alignment

4.5 Adjustment

Sensor with potentiometer:

The sensitivity is adjusted with the potentiometer (type: 270°). Clockwise rotation:

operating reserve increased; counterclockwise rotation: operating reserve reduced. We

recommend setting the potentiometer to "Maximum."

The sensor is adjusted and ready for operation. Refer to graphics C and G to check the

function. If the switching output fails to behave in accordance with graphic C, check

application conditions. See section Fault diagnosis.

(PNP)

(NPN)

Figure: C

4 COMMISSIONING

88016954.1ABM / 2020-12-21 | SICK

Subject to change without notice

Figure: G

5 Additional functions

Test input: The GRSE18 sensor features a test input ("TI" or "Test" on the connection

diagram [B]), which can be used to switch the sender off and therefore check that the

sensor is functioning correctly: If female cable connectors with LED indicators are used,

you must ensure that the TI is assigned accordingly.

There must be no object between the sender and receiver; activate the test input (see

the connection diagram [B], TI at 0 V). The send LED is shut down or the detection of

an object is simulated. Refer to graphics C and G to check the function. If the switching

output fails to behave in accordance with graphic C, check application conditions. See

section Fault diagnosis.

6 Troubleshooting

The Troubleshooting table indicates measures to be taken if the sensor stops working.

Table Fault diagnosis

LED indicator/fault pattern Cause Measures

Green LED does not light up No voltage or voltage below

the limit values

Check the power supply,

check all electrical connec‐

tions (cables and plug connec‐

tions)

Green LED does not light up Voltage interruptions Ensure there is a stable power

supply without interruptions

Green LED does not light up Sensor is faulty If the power supply is OK,

replace the sensor

Green LED lights up, no output

signal when object is detected

Test input (Test) is not con‐

nected properly

See the note on connecting

the TI

Yellow LED flashes Sensor is still ready for oper‐

ation, but the operating condi‐

tions are not ideal

Check the operating condi‐

tions: Fully align the beam

of light (light spot) with the

receiver. / Clean the optical

surfaces . / Readjust the sen‐

sitivity (potentiometer) / If the

potentiometer is set to the

max. sensing range: Reduce

the distance between the

sender and the receiver and

check / Check sensing range

COMMISSIONING 4

8016954.1ABM / 2020-12-21 | SICK

Subject to change without notice 9

LED indicator/fault pattern Cause Measures

and adjust if necessary, see

„Check the application condi‐

tions“, page 5.

Yellow LED lights up, no object

in the path of the beam

The beam of light of a pho‐

toelectric through-beam sen‐

sor hits the receiver of

another (neighboring) photo‐

electric through-beam sensor

Swap the sender and receiver

arrangement at every sec‐

ond through-beam photoelec‐

tric sensor and ensure that

there is sufficient distance

between the through-beam

photoelectric sensors, see

figure X.

7 Disassembly and disposal

The sensor must be disposed of according to the applicable country-specific regula‐

tions. Efforts should be made during the disposal process to recycle the constituent

materials (particularly precious metals).

NOTE

Disposal of batteries, electric and electronic devices

•According to international directives, batteries, accumulators and electrical or

electronic devices must not be disposed of in general waste.

•The owner is obliged by law to return this devices at the end of their life to the

respective public collection points.

•

WEEE: This symbol on the product, its package or in this document,

indicates that a product is subject to these regulations.

8 Maintenance

SICK sensors are maintenance-free.

We recommend doing the following regularly:

•Clean the external lens surfaces

•Check the screw connections and plug-in connections

No modifications may be made to devices.

Subject to change without notice. Specified product properties and technical data are

not written guarantees.

9 Technical specifications

GRSE18-xxx4x GRSE18-xxx2x

Recommended sensing range for the best performance 0 ... 15 m 0 ... 15 m

Sensing range max. 0 ... 15 m 0 ... 15 m

Light spot diameter/distance 250 mm / 10 m 250 mm / 10 m

Supply voltage UBDC 10 ... 30 V1) DC 10 ... 30 V1)

Ripple

Output current Imax. 100 mA 100 mA

7 DISASSEMBLY AND DISPOSAL

10 8016954.1ABM / 2020-12-21 | SICK

Subject to change without notice

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere SICK Sicherheitssensor Handbücher

SICK

SICK KTS-WB51141142ZZZZ Bedienungsanleitung

SICK

SICK GTE6 Series Bedienungsanleitung

SICK

SICK WL24-2 Series Bedienungsanleitung

SICK

SICK GSE6V Bedienungsanleitung

SICK

SICK Prime KTX-WB9114225UZZZZ Bedienungsanleitung

SICK

SICK GTE6V Bedienungsanleitung

SICK

SICK UM18-2 Pro Bedienungsanleitung

SICK

SICK Prime KTX-WP91342252ZZZZ Bedienungsanleitung

SICK

SICK OLM200 Bedienungsanleitung

SICK

SICK Prime KTS-WP91241152ZZZZ Bedienungsanleitung

SICK

SICK C4000 Select Betriebsanleitung

SICK

SICK deTem4 Core Ex Bedienungsanleitung

SICK

SICK AS30 Prime Edge Bedienungsanleitung

SICK

SICK KTX Prime Bedienungsanleitung

SICK

SICK DL100 Pro Bedienungsanleitung

SICK

SICK LD-OEM15 Series Bedienungsanleitung

SICK

SICK SIM4 00 Series Bedienungsanleitung

SICK

SICK Core KTS-WB41141142ZZZZ Bedienungsanleitung

SICK

SICK WTB4F Bedienungsanleitung

SICK

SICK UE410-SD Bedienungsanleitung

SICK

SICK deTem2 Core Bedienungsanleitung

SICK

SICK WLL80 Analog Bedienungsanleitung

SICK

SICK miniTwin4 Bedienungsanleitung

SICK

SICK PowerProx WTT12L Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung