Side-Power RC-12E Bedienungsanleitung
Installation & User Manual
Radio Remote RC-12E
Made in Norway
©Sleipner Motor AS version 1.0 - 2012
SLEIPNER MOTOR AS
P.O. Box 519
N-1612 Fredrikstad
Norway
Tel: +47 69 30 00 60
Fax: +47 69 30 00 70
www.side-power.com
sidepower@sleipner.no
Installation & User Manual, Radio Remote RC12E Page 2
Model range................................................................................................................................ 2
Technical specications .............................................................................................................. 3
Important precautions................................................................................................................. 4
Receiver installation ................................................................................................................... 6
“Visual” wiring diagram................................................................................................................ 6
Programming additional transmitters........................................................................................... 7
Replacing the batteries............................................................................................................... 8
User precautions ........................................................................................................................ 9
How to use the windlass remote................................................................................................ 10
Service Partners ...................................................................................................................... 12
Model range
Contents
We Sleipner Motor AS declare that this
device complies with health and safety
requirements according to the Directives
EN301 489-3 V1.4.1:2002
EN301 489-1 V1.4.1:2008
IEC 60533:1999
EN300 220-1 V2.3.1:2010
EN300 220-2 V2.3.1:2010
The radio remote control can control two independent windlasses. The receiver can receive the
signals of up to four transmitters.
Remote control kit (RC-12E) consists of:
- Receiver: Part no. RCR-1E
- Transmitter (incl. battery): Part no. RCT-12E
- Holding bracket for transmitter unit: Part no. RC-HOLDER
Additional transmitters can be ordered separatly: Part no. RCT-12E
Antenna is available as spare part no. RC-ANT
The transmitter and the receiver have the same factory preset code so no programming is neces-
sary. The battery is already inserted in the transmitter.
When additional transmitters are to be used, the receiver must be programmed again for all trans-
mitters (please see programming section on page 7).
Installation & User Manual, Radio Remote RC12E Page 3
Technical specications
• You should always install at least one original windlass panel.
•Use the remote only for shorter periods of time to preserve transmitter battery life. Use the
main control panel for longer runs of the windlass.
• This manual is intended to support educated / experienced staff and is therefore not sufcient
in all details for the correct installation.
• When installed in boats approved or classied according to international or special national
rules, the installer is responsible for following the demands in accordance with these regula-
tions / classication rules. The instructions in this guide can not be guaranteed to comply with
all different regulations / classication rules.
•The transmitter and the receiver have the same factory preset code so no programming is nec-
essary. When additional transmitters are to be used, the receiver must be programmed again
for all transmitters (please see programming section on page 7).
Transmitter Receiver
Model RCT-12E RCR-1E
Power feed 1 x 3V battery (type: CR2032) From windlass supply
Frequency (MHz) 433,2 433,2
Operation temp. -10°C / +55°C -15°C / +55°C
HxWxD (mm) 95x48x25 89x68x33
Weight (g) 60 135
Voltage: 8-30V
Load, max 4A
Operating range: 15m under normal operating conditions
Important precautions
Installation & User Manual, Radio Remote RC12E Page 4
Receiver installation
Prior to installation, it is important that the responsible installer reads this guide to ensure
necessary acquaintance with this product.
Warning!
• Remote receiver power supply negative lead must be connected to the windlass negative lead.
Caution!
• Install the receiver minimum 1 meter (3ft) from high power cables and NMEA cables or other
sources of electrical interference, i.e. navigation instruments, radio communication devices,
electro motors and generators.
• Install the receiver outside of shielded areas for radio signals, i.e. boxes made of steel or other
material with shielding properties.
• Install the receiver in a dry environment, with cables pointing downwards. (The receiver as-
sembly is not waterproof.)
• When additional transmitters are to be used, the receiver must be programmed again for all
transmitters (please see programming section on page 7).
• The receiver must have a separate power supply tted with a 5 Amp fuse in the positive lead
that has either a separate power switch or is shut of by the windlass main power switch.
• Mount the receiver using the two screw holes (please see picture on page 6).
If the receiver is mounted against a wall, use spacers between the receiver and the wall to
avoid moisture in the receiver.
Optimised installation (Fig. 1 - 3)
• The receiver antenna must be placed in a vertical position minimum 1 meter (3ft) above sea
level.
• The receiver has antenna with SMA connector. If there is a problem with signal transferring, try
to move the unit to a more optimised position or buy the antenna extension cable (RC-EXT) to
relocate the antenna.
- Above sea level
- Away from sources of electrical interference.
Note! Faulty installation will render all warranty given by Sleipner Motor AS void.
Installation & User Manual, Radio Remote RC12E Page 5
Installation & User Manual, Radio Remote RC12E Page 6
Visual wiring diagram
Mount the receiver by using
the 2 screwholes.
Receiver installation
If the receiver is mounted
against a wall, use spacers
between the receiver and the
wall to avoid moisture in the
receiver.
blue
grey
red (B+)
signal windlass up
windlass ctrl. power
signal w.lass down
Windlass 2
STERN
Yellow: Not in use
Red: 12/24V Batt. + (5A fuse!)
5 A
Fused power supply from a
circuit with ON/OFF switch!
Black: 12/24V Batt. -
blue
grey
red (B+)
signal windlass up
windlass ctrl. power
signal w.lass down
Windlass 1
Yellow: Not in use
Receiver Part# RCR-1E
BOW
Installation & User Manual, Radio Remote RC12E Page 7
Programming additional receivers
The original transmitter and receiver have the same factory preset code so that no programming
is necessary. When additional transmitters are to be used, the receiver must be programmed
again for all transmitters.
1. Deactivate the receiver and all transmitters (press “OFF” on all transmitters).
Turn off the main power switch for the windlass(es).
2. Turn on the power to the receiver.
3. Push the Pair Button on the receiver with a plastic stick (as shown above).The LED below the
button will start to blink.
4. The receiver and transmitter are programmed by pressing both “ON” buttons on the transmit-
ter. Within 5 seconds the LED will change from blinking to continous light when the program-
ming signal is received. The transmitter is then ready to use.
5. Additional transmitters must be programmed according to step 3-4 when the receiver is in
“Program mode”. You can pair up to 4 transmitters.
6. To clear all transmitters, hold Pair Button until LED blinks slow, continue to hold button pressed
until LED blinks quick indictaing that a reset process is started. When LED is turned off, the
reset process is completed, and the Pair button can be released. The LED will come on when
the receiver has completed the reset process and is ready to be paired (Step 3-4)
Push the Pair Button with a plastic stick
Installation & User Manual, Radio Remote RC12E Page 8
WARNING:
Before working on the transmitter, deactivate the transmitter and the receiver (push “OFF” on the
transmitter(s)) and turn off the power to the receiver as well as the windlass mainswitch.
1. Open the transmitter.
2. Take out the battery by inserting a screwdriver or similar between battery and holder at point A,
and gently ip the battery out, taking care not damaging the battery grips at point B
3. Insert the new battery (Type CR2032, 3V - Brand name recommended). Be sure to insert the
battery with the positive pole up diagonally into the battery holder, conrming that the edge of
the battery is under the battery grips (B). Press the battery down until secured at point A.
4. Close the transmitter. Put the cover back in place, ensure that the rubber seal between remote
upper and lower part is located correctly. Place the 3 screws (remember sealing washer) in
their recessed holes and tighten.
Replacing the battery
Battery
A
B
AB
Installation & User Manual, Radio Remote RC12E Page 9
Important user precautions
• Ensure that you know the location of the main battery switch that disconnects the windlass
from all power sources (batteries) so that the windlass can be turned off in case of a malfunc-
tion.
• How to activate the system:
Turn on the main power source for the windlass system. Turn on the power to the receiver.
The windlass system is then activated by pushing the two “ON” buttons on the transmitter (see
page 10). To turn of the radio remote control press the “OFF” button on the transmitter for 2 sec.
The LED below the Pair Button on the receiver will blink when a command signal is received.
• Alarms:
If transmitter/receiver is out of range, the transmitter will give an alarm sound.
If the voltage of the battery supplying the windlass gets below 8V, the alarm will sound.
If other alarm situations are detected by the receiver, the transmitter will give an alarm sound.
• The transmitter will automatically turn off after approx. 4 minutes of inactivity for safety reasons
When using a single transmitter
The system turns off automatically approx. 4 minutes after the last usage.
When using more than one transmitter
The system turns off automatically approx. 4 minutes after the last usage of the control unit that
initially activated the system even if other control units have been operated in the meantime.
The system is off even if these other control units still show the blinking LED on the transmitter.
To use these transmitters, the system must be activated again by pushing the two “ON” buttons.
• Remember to turn off the radio remote control by pushing the “OFF” button on the transmitter
for 2 seconds and to turn off the power switch for the receiver when nished using your wind-
lass
Installation & User Manual, Radio Remote RC12E Page 10
How to use the remote control
1. Turn the main power switch for the windlass on. Turn on the power to the receiver.
2. Turn on the transmitter by pushing the transmitter’s two “ON” buttons. The remote system is
now activated and then turns off automatically appr. 4 min. after the last usage (see page 9).
3. Use the remote only for shorter periods of time to preserve transmitter battery life. Use the main
control panel for longer runs of the windlass.
How to use the windlass
Please consult your windlass manual for use and precautions.
NB: Max. load on the windlass signal output is 4A!
If the windlass requires more than 4A, use extra control relay (ref. llustration next page)
Remote Control Deactivation
Push the transmitter’s “OFF” button for two seconds (the remote control deactivates automati-
cally after approx. 4 minutes after the last usage). Turn off the power switch for the receiver.
Remote control “ON” Windlass 2
Remote control “OFF”
Auto-OFF
appr. 4 min.
Down
Up
Hold for
2 seconds
Windlass 1
Down
Up
Inhaltsverzeichnis
Andere Side-Power Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
