Siemens A62 Bedienungsanleitung

right page (1) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:20)

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Overview.fm

Overview of the phone

VAR Language: en; VAR issue date: 041111

Overview of the phone

1Display indicators

Signal strength/GPRS/battery level.

2Soft keys

Press the soft key to call up the function

that is displayed as §Text§ or icon on the

grey fields above the key.

3ACall key

Dial displayed phone number or name,

accept calls. In standby mode: Display the

last calls.

4BOn/Off/End key

• Switched off: press and hold to

switch on.

• During a conversation or in an

application: press briefly to finish.

• In menus: press briefly to go back a

level. Press and hold to return to

standby mode.

•Instandbymode:press and hold to

switch off phone.

5Navi-key

In lists and menus

GScroll up and down.

DFunction call.

CBack a menu level.

During a call

DOpen call menu.

In standby mode

FOpen Phonebook.

DOpen menu.

CGPRS info.

6*Press and hold

• In standby mode: switch on/off all

signal tones (except alarm).

• For incoming calls: only switch off ring

tones.

7Press and hold

In standby mode: switch key lock on/off.

_ªg

Service provider

17.02.2005 09:15

New SMS Menu

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Main.fm

left page (2) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:22)

Getting started

VAR Language: en; VAR issue date: 041111

Getting started

Using the SIM card/battery

Your phone's display is delivered with a

protective film. Remove this film before get-

ting started. The service provider supplies

you with a SIM card on which all the im-

portant data for your account is stored. If

the SIM card is credit card-sized, snap out

the smaller segment and trim any rough

edges.

Remove the battery cover upwards 1.

Insert SIM card 2and push it fully into

the locating slot (make sure the angled

corner is in the correct position 3). Then

push the retaining catch over the top of

the SIM card 4.

Insert the battery sideways into the

phone 5, then press downwards 6

until it engages.

To remove, press the retaining tab 7

then lift the battery out.

Insert the battery cover by the tabs at the

bottom 8, then press downwards 9,

until it engages.

Always switch off phone before removing

the battery!

Only 3 V SIM cards are supported. Please

contact your service provider if you have

an older card.

Charging the battery

The battery is not supplied fully charged.

Plug the charger cable into the bottom of

the phone, plug the power supply unit

into a mains power socket and charge for

at least two hours.

right page (3) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:22)

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Main.fm

Switch on/off, PIN entry

VAR Language: en; VAR issue date: 041111

Charging time

The charging time is 2 hours. Ambient

temperature of 5 °C to 40 °C (icon flashes

as a warning when 5 °C above/below this).

Switch on/off, PIN entry

Switch on/off

Press and hold On/Off/End keyBto

switch on or off.

Enter PIN

The SIM card can be protected with a

4–8 digit PIN. Enter the PIN code using

the number keys (the display shows a

series of asterisks, if you make a mistake

press §Clear§). Confirm your input with §OK§.

Logging on to the network will take a few

seconds.

First time switching on phone, the time

and date must be set.

Standby mode

When the name of the service provider/

logo appears on the display, the phone is

in standby mode and ready for use.

Press and hold the On/Off/End keyBto

return to standby mode from any menu

option.

Security

The phone and SIM card are protected

against misuse by several security codes.

Keep these confidential numbers in a safe

place where you can access them again if

required.

§Menu§ ¢m¢Security ¢Codes

¢Select a function.

PIN control

The PIN is usually requested each time

the phone is switched on. You can deacti-

vate this feature but you risk unauthor-

ised use of the phone. Some service pro-

viders do not permit deactivation of the

control.

Change PIN

You can change the PIN to any 4–8 digit

number you may find easier to remember.

Change PIN2

(Displayed only if PIN2 is available.)

Proceed as with Change PIN.

Change phonecode

You define and enter the phone code

(4–8 digits) when calling a phone code

protected function (e.g. Direct call, p. 5)

for the first time. It is then valid for all

protected functions. If it is entered incor-

rectly three times the phone is locked.

Contact the Siemens Service.

Clear SIM card barring

If the PIN is entered incorrectly three

times, the SIM card is barred. Enter the

PUK (MASTER PIN) provided by your serv-

ice provider with the SIM card. If the PUK

(MASTER PIN) has been lost, please con-

tact your service provider.

Prevent accidental activation

Even if PIN use is deactivated confirma-

tion is required to switch on the phone.

This prevents accidental activation of the

phone, e.g. when you are carrying it in

a bag or when you are travelling in an

aircraft.

After pressing and holding the On/Off/End

keyBselect §OK§ to switch on the phone

or abort the operation with any key

except §OK§.

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Main.fm

left page (4) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:22)

Making a phone call

VAR Language: en; VAR issue date: 041111

Making a phone call

Dialling with number keys

The phone must be switched on (standby

mode). Enter the number (always with

prefix, if necessary with the international

dialling code). Press §Clear§ to clear the last

digit, press and hold to clear the entire

phone number. To dial press theAkey.

End call

Press the End keyBbriefly. Press this key

even if the person on the other end of the

line has hung up first.

Set volume

Use the scroll keyEto start adjusting

the volume during conversation. Set vol-

ume withG.

Redial previous numbers

To redial the phone number last called,

press the Call keyAtwice. To redial other

numbers that were dialled previously,

pick out the required phone number from

the list withG, then pressAto dial.

When a number is busy

For automatically dialling the phone

number for up to 15 minutes at increas-

ing intervals, press §Auto dial§. For phone

ringing when the busy number is free,

press §Call back§ (L). Press §Prompt§ and a

beep will remind you to redial the dis-

payed phone number after 15 minutes.

Accept call

The phone must be switched on (standby

mode). An incoming call will interrupt

any other use of the phone.

Press §Answer§ orA.

If the phone number has been transmitted

by the network, it is displayed. If the number

and the name are stored in the Phonebook,

the corresponding name is displayed in-

stead. If set, an animation can be dis-

played instead of the bell icon.

Reject call

§Reject§ or Bpress briefly.

Swapping between 2 calls b

Make a new connection during a call with

ymenu§ ¢Hold ¢J(dial new phone

number, also from Phonebook:F). With

§Swap§ you can swap back and forth be-

tween both calls.

Additional costs will be incurred for the

2nd phone connection.

Conference b

Make a new connection during a call with

ymenu§ ¢Hold ¢J(dial a new phone

number).

With ymenu§ ¢Conference you can join

the held call. Repeat this procedure until

all participants are linked together (up to

5participants).

All calls in the conference are ended si-

multaneously when the End keyBis

pressed.

Additional costs will be incurred for every

additional phone connection.

Handsfree

You can put the phone down during a

call. You can then hear the caller via the

loudspeaker. Press §Handsfr.§ and §Yes§

to activate handsfree function. Press

§Handsfr.§ to switch off.

Warning!

Please make sure you have accepted the

call before holding the phone to your ear.

This will prevent a loud ring tone from

damaging your hearing!

right page (5) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:22)

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Main.fm

Phonebook

VAR Language: en; VAR issue date: 041111

Call menu

Several functions are only available

during a call:

ymenu§ ¢Select a function.

Direct call

The phone can be locked, so it's only pos-

sible to dial a defined number.

Switch on

§Menu§ ¢m¢Security ¢Direct call

Press §Select§ and enter phone code. When

first prompted you define and enter the

phone code (4–8 digits). Please do not for-

get this code! Confirm input with §OK§ and

press §Change§. Select phone number from

the Phonebook or enter a new one. With

§OK§ confirm ON.

Use

Press and hold the right soft key

>to dial.

Switch off

Press and hold and enter phone code.

Confirm input with §OK§ and press §Change§.

With §OK§ confirm OFF.

Phonebook

Open Phonebook (in standby mode)

Fselect <New entry> ¢§Select§

¢GActivate input fields.

Number: Always enter phone number with

an area dialling code.

Name: Enter first name or surname.

Group: Organise entries in groups, select

with §Change§.

Location: Select location: SIM (SIM card),

Mobile (phone memory) or Protected SIM

(special SIM card).

Record no.: This is automatically assigned

to the entry. Change with §Change§.

Press §Save§ to store the new entry.

Text entry

Press number key repeatedly until the re-

quired letter appears. The cursor advanc-

es after a short delay. Example:

2Press once for a, twice for b etc.

Press and hold to write the

number.

Ä, ä, 1–9 Umlauts and numbers are dis-

played after the relevant letters.

§Clear§ Press briefly to delete the letter

before the cursor, press and hold

to delete the whole word.

HMove the cursor (forwards/back).

Press briefly: Switch between:

abc, Abc, ABC, T9abc, T9Abc,

T9ABC, 123. Status indicator in

the top line of the display.

Press and hold: All input modes

are displayed.

*Press briefly: Select special

characters.

Press and hold: Open input menu.

0Press once/repeatedly:

. , ? ! ’ “ 0 - ( ) @ / : _ + ~ &

Press and hold: Writes 0.

1Writes blank. Press twice =

skip line.

Call/search for an entry

Open PhonebookF, select name by typ-

ing first letter or scroll and dial withA.

Call with record no.

A record number is automatically assigned

to every new entry in the Phonebook.

JEnter record number (in standby

mode) ¢¢A

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Main.fm

left page (6) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:22)

Messages (SMS)

VAR Language: en; VAR issue date: 041111

Edit entry

G¢Select entry ¢§Options§ ¢Edit

¢G(select required input field)

¢Make changes ¢§Save§

Assign picture

If a picture is assigned to an entry, this

picture is displayed for the appropriate

call.

G¢select entry ¢§Options§ ¢Picture

¢Iselect picture ¢§Open§ ¢§Select§

Groups

If there are many Phonebook entries it is

best to assign them to a group, e.g.:

Family, Friends, VIP

A special ring tone can sound and/or a sym-

bol can be displayed if the phone number

of a call is registered in a group.

Select a group

FOpen Phonebook in standby mode

¢<Groups> ¢Gselect a group

¢§Select§

All entries of the selected group are

displayed.

Change group assignment

You can assign a Phonebook entry to a

group when you enter it.

FOpen Phonebook ¢GSelect entry

¢§Edit§ ¢G(scroll to group) ¢§Change§

¢Select a new goup ¢§Save§

Group call tones

You can assign different ringtones to

groups.

§Menu§ ¢ç¢Group calls

¢GSelect a group ¢§Select§

¢GSelect ring tone ¢§Select§

Messages (SMS)

Read messages

A new message is indicated on the display

with …. Press the left soft key to read the

message. Scroll through the message line

by line withG.

§Reply§ Functions for a direct reply.

Inbox/outbox/archive

§Menu§ ¢]¢Inbox or

Outbox or SMS archive

The list of saved messages is shown.

Compose a message

§Menu§ ¢]¢New SMS ¢Write text

¢A¢J/Q(enter phone

number or select from Phonebook)

¢§OK§

The SMS is sent to the service centre for

transmission.

SMS to group

Write text ¢§Options§ ¢Send ¢§Group§

select group members and send SMS.

Picture&sound

Insert pictures/sounds in the message

text.

Write text ¢§Options§ ¢Picture&sound

¢GSelect picture/sound. The picture/

sound is inserted in the SMS.

Text menu

§Options§ Open the text menu.

Write text fragments

§Menu§ ¢]¢Predef. texts

¢§Options§ ¢<New entry>

¢J(write textfragment) ¢§Save§

right page (7) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:22)

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Main.fm

Profiles

VAR Language: en; VAR issue date: 041111

Use text fragments

J(write message text) ¢§Options§

¢Predef. texts ¢G(select text frag-

ment from the list) ¢§Select§

The text fragment is inserted into the text

to the left of the cursor.

Text entry with T9

T9 deduces the correct word from the in-

dividual key entries by making compari-

sons with an extensive dictionary. Write a

word and finish it without looking at the

display. Simply press the keys where the

relevant letter is located once. If several

options are found in the dictionary the

most probably is displayed first. For fur-

ther options please press the right

softkey.

Profiles

§Menu§ ¢~

Three profiles are standard with default

settings, they can be changed however:

Normal envi., Quiet environ., Noisy environ.,

Car Kit (only with an original Siemens

handsfree Car kit), Headset (only with an

original Siemens headset).

You can set two personal profiles

(<No Title>).

The special profile Aircraft mode cannot be

changed.

Activate

Select default profile or personal pro-

file:G¢§Activate§.

Change setting

GSelect profile ¢§Options§

¢Change sett.

The list of available functions is displayed.

Aircraft mode

The phone will automatically switch off if

you select this profile. Even the alarm

tone is deactivated. An alarm is only

shown on the display. It is not possible to

modify this profile.

The next time you switch on the phone

the default profile will be activated.

T9® Text Input is licensed under one or more

of the following:

U.S. Pat. Nos. 5,818,437, 5,953,541, 5,187,480,

5,945,928 and 6,011,554;

Canadian Pat. No. 1,331,057;

United Kingdom Pat. No. 2238414B;

Hong Kong Standard Pat. No. HK0940329;

Republic of Singapore Pat. No. 51383;

Euro.Pat. No. 0 842 463 (96927260.8)

DE/DK, FI, FR, IT, NL, PT, ES, SE, GB;

and additional patents are pending worldwide.

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Main.fm

left page (8) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:22)

Setup

VAR Language: en; VAR issue date: 041111

Setup

Display

§Menu§ ¢m¢Display

¢Select a function.

Language

Set the language of the display text.

"Automatic" will set the language of your

home service provider. Reset to this lan-

guage in standby status:

*# 0 0 0 0 # A

Screensaver

The screensaver shows a picture on the

display as soon as a period that can be set

by you has elapsed. The function is ended

by an incoming call or by pressing any key.

Call setup

§Menu§ ¢m¢Call setup

¢Select a function.

Hide ID b

When switched off, the display of the call-

ing party shows your phone number (de-

pendent on service provider). To suppress

this display, you can activate the "Hide ID"

mode.

Call waiting b

If you are registered for this service, you

can check whether it is set and you can

activate/deactivate it with Call waiting.

Any to answer

Incoming calls can be accepted by press-

ing any key(except forB).

Minute beep

During the call, you will hear a beep after

each minute as a reminder of the time

elapsed. The receipt does not hear the

beep.

Divert

You can set the conditions for which calls

are diverted to your mailbox or other

numbers.

§Menu§ ¢m¢Divert

¢Select a function.

Set up call divert (example)

All calls b

All calls are diverted. nis shown in the

top line of the display in standby mode.

Unanswered calls b

Includes Unanswered, Not reachable,

No reply, Busy.

§Select§ ¢Set ¢J(Enter the phone

number to which the call should be

diverted) ¢§OK§

After a short pause, the setting is con-

firmed by the network.

Status check

After a short pause the current informa-

tion is shown.

pCondition set.

oNot set.

sDisplay, if status is unknown

(e.g. on a new SIM card).

Clear all b

All set diversions are cleared.

Clock

§Menu§ ¢m¢Clock

¢Select a function.

right page (9) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:22)

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Main.fm

Setup

VAR Language: en; VAR issue date: 041111

Security

§Menu§ ¢m¢Security

¢Select a function.

Direct call

Only one phone number can be dialled.

Press and hold the right soft key.

This SIM only b

Your phone is prevented from being used

with a different SIM card.

Only ‚b

Restrict calls to SIM-protected numbers in

the Phonebook.

Last 10 only

Limit calls tocall list of "dialled numbers".

Barrings b

Network barring restricts the use of your

SIM card.

All outgoing: Outgoing calls, except emer-

gency 999 calls, are blocked.

Outgo internat: Only national calls can be

made.

Out.int.x home: International calls are not

permitted, except for calls to your home

country.

All incoming calls: The phone is blocked

from receiving all incoming calls.

When roaming: You do not receive any calls

outside your home network.

Status check: Query the status of your

barrings.

Clear all: Clear all barrings. Password pro-

tected!

Phone identity

The phone identity number (IMEI) is

displayed.

Factory settings

The phone is reset to the default values

(does not apply to SIM card and network

settings).

Alternative input in standby mode:

*# 9 9 9 9 # A

Network

§Menu§ ¢m¢Network

¢Select a function.

Line b

Two independent phone numbers have to

be registered.

Network info

The list of GSM networks currently availa-

ble is displayed.

Auto network

If activated, the next network is dialled in

the order of your "preferred networks".

Choose network

The network search is restarted.

Preferred network

Set the service providers you prefer when

you leave your home network.

Fast search

Speed up network reconnection.

Siemens AG 2003, E:\Auftrag\Siemens\MobilePhones\A62 Artemis V2\en\Artemis_Main.fm

left page (10) of A62 Artemis en, A31008-H5890-A1-2-7619 (29.12.2004, 11:22)

Ring tones

VAR Language: en; VAR issue date: 041111

Ring tones

§Menu§ ¢ç¢Select a function.

Set the tones to match your needs.

Ringer setting

Activate/deactivate the ring tone or

reduce it to a short beep.

Silent alert

Activate/deactivate the silent alert

(functions in addition to ringer).

Volume

Set the same volume for all ring tones.

GSet volume.

§OK§ Confirm.

dCalls, Group calls, Other calls,

Alarm clock, Messages

The ring tones for the stated types of call/

functions can be set separately.

More tones...

Call screening b

Only calls from numbers that are in the

Phonebook or in a predefined group are

signalled audibly or by silent alert. Other

calls are only displayed.

Key tones

Set acoustic key acknowledge:

Click or Tone or Silent

Minute beep

During the call, you will hear a beep once

a minute as a reminder.

Info tones

Set service and alarm tones.

Andere Handbücher für A62

Inhaltsverzeichnis

Andere Siemens Handy Handbücher

Siemens

Siemens Gigaset SL56 Bedienungsanleitung

Siemens

Siemens SX66 Bedienungsanleitung

Siemens

Siemens PEGASUS-DTC AX72 Bedienungsanleitung

Siemens

Siemens Gigaset Gigaset S1 Bedienungsanleitung

Siemens

Siemens S65 Bedienungsanleitung

Siemens

Siemens M46 Bedienungsanleitung

Siemens

Siemens A62 Einrichtungshandbuch

Siemens

Siemens C75 Einrichtungshandbuch

Siemens

Siemens Gigaset S2 HiPath 4000 Bedienungsanleitung

Siemens

Siemens SK65 Sicherheitsleitfaden

Siemens

Siemens ST55 Bedienerhandbuch

Siemens

Siemens A65 Bedienungsanleitung

Siemens

Siemens SXG75 Einrichtungshandbuch

Siemens

Siemens SL45i Bedienungsanleitung

Siemens

Siemens C55 Bedienungsanleitung

Siemens

Siemens XELIBRI 2 Bedienungsanleitung

Siemens

Siemens S40 Bedienungsanleitung

Siemens

Siemens sx45 Bedienungsanleitung

Siemens

Siemens Gigaset S56 Bedienungsanleitung

Siemens

Siemens SOMATOM Sensation Cardiac Version A60 Bedienungsanleitung

Siemens

Siemens Gigaset Powerline Adapter 200 Bedienungsanleitung

Siemens

Siemens EF81 Bedienungsanleitung

Siemens

Siemens CX70 Bedienungsanleitung

Siemens

Siemens M75 Bedienungsanleitung

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LG LM-X420QN Bedienungsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

LG LM-K420EMW Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung