Siemens MPS-6 Bedienungsanleitung

Installation Instructions

Model MPS-6

Power Supply Module

P/N 315-090334-8

OPERATION

The Model MPS-6 from Siemens Industry, Inc. is a

fully supervised power supply that provides the MXL

System with primary 24 VDC power. It is rated at 6.5

amps and is unfiltered and unregulated. The MPS-6

supplies the MXL Control Panel or PSR-1 and its

expansion modules with the power required for

normal operation. The module incorporates a 2 amp

resettable circuitbreaker on the primary input and

includes a built-in AC line filter for surge and noise

suppression. The MPS-6 mounts in an MXL enclo-

sure backbox.

INSTALLATION

Always remove power before installation.

The installation kit for the MPS-6 includes the

following:

Four #10 nuts

Two #10 lockwashers

Two #10 flat washers

Two ¼" nuts

One 14 gauge green ground strap

The MPS-6 is designed to operate from a 120 VAC,

60 Hz power source. Use a separate or dedicated

circuitbreaker. Wire in accordance with local codes

and Article 760 of the NEC, NFPA 70, latest edition.

Run the earth ground from a suitable source to the

MPS-6. Check local requirements. Conduit is not

an acceptable conductor.

1. Make sure that the dedicated circuitbreaker

for the MPS-6 is turned off at the mains.

2. Place the mounting bracket for the MPS-6 over

the two studs provided in the enclosure. (Refer to

Figure 1.)

3. Secure the MPS-6 to the enclosure by slipping the

flat washers, then the lockwashers, and finally the

nuts over the two studs. Tighten them securely.

4. Connect the AC mains to the MPS-6:

Terminal

Black (hot) 1

White (neutral) 2

Green (earth ground) 3

5. Install the 14 gauge green ground strap spade lug

side to Terminal 3 (green, earth ground) of the

MPS-6. Secure the ring lug side of the ground

strap to the nearest available stud in the enclo-

sure. The stud size may vary depending on the

actual system modules and enclosure used.

Because the stud may be either a #10 thread or

¼" thread, nuts for both have been provided. The

ground strap provided is long enough for all

applications and the ring lug is good for both #10

and ¼" studs. If possible, install the ring lug under

one of the lock-washers and nuts which secure

the MPS-6 itself.

6. When used with a PSR-1:

Connect the 3-wire cable coming from the MPS-6

to the PSR at P12.

When used with an MMB-1/-2/-3 or SMB-1/2:

Connect the 3-wire cable coming from the MPS-6

to the MMB-1/-2/-3 or the SMB-1/2 at P1.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

P/N 315-090334-8

Figure 2

Front of MPS-6

Figure 1

MPS-6 in MXL Enclosure

POWER CABLE TO:

MMB-1/-2/-3, P1

SMB-1/-2, P1

PSR-1, P12

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens SIMATIC TI505 Bedienungsanleitung

Siemens

Siemens SINUMERIK 828D Turning Betriebsanleitung

Siemens

Siemens HTRI-M Bedienungsanleitung

Siemens

Siemens SIMATIC RF120C Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens HCP Bedienungsanleitung

Siemens

Siemens Cerberus Pyrotronics NIM-1M Bedienungsanleitung

Siemens

Siemens S-60 Bedienungsanleitung

Siemens

Siemens XCI2001-U1 Leitfaden

Siemens

Siemens SIMATIC ET 200SP IM 155-6 PN/2 HF Bedienungsanleitung

Siemens

Siemens Simatic ET200pro Bedienungsanleitung

Siemens

Siemens SIMOTION D4x5-2 Bedienungsanleitung

Siemens

Siemens SCALANCE W788C-2 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens QPA228.FWNC Series Bedienungsanleitung

Siemens

Siemens SINAMICS G120 Datenblatt

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SINAMICS S120 Technisches Dokument

Siemens

Siemens ZIC-4AC Bedienungsanleitung

Siemens

Siemens 8GK9735-1KK.0 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840C Bedienungsanleitung

Siemens

Siemens SINUMERIK Series Stücklistenhandbuch

Siemens

Siemens ASIC SIM 1-2 Stücklistenhandbuch

Siemens

Siemens SIMATIC NET CP 142-2 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung