Siemens OCC-1 Bedienungsanleitung

INTRODUCTION

The Model OCC-1 Output Control Card

from Siemens Building Technologies, Inc.

is an MXLV module that controls Voice

system cards (such as the zone cards)

that plug into the OMM-1 Output Master

module. Commands received from the

MXL system through the network bus are

processed by the OCC-1. The commands

are then sent to the other cards in the

system for implementation.

At least one OCC-1 is required in each

MXLV System. It supervises and controls

up to 11 plug-in cards, each having a

unique subaddress. Several types of

system cards connect to the OCC-1.

1. Up to three audio risers connect to the

OCC-1. These signals are available to

the power amplifiers.

2. The BTC-1 Backup Tone card is an

optional module that also plugs into

the OCC-1. In an installation with

distributed amplification, the BTC

provides the tone for the degrade

mode of operation; then, if Network

Communications fail and a local alarm

is detected, the tone from BTC-1 is

available at the Channel A amplifier

input.

3. The telephone riser also connects to

the OCC-1. The telephone signal is

routed through the OMM-1 telephone

riser bus to any ZCT-8B telephone

zone control cards that are plugged

into the OMM-1.

P/N 315-090918-12

Installation Instructions

Model OCC-1

Output Control Card

The OCC-1 supervises the cards under its

control, such as the ZC zone card series.

As each card is supervised by the OCC-1,

the card responds with its status. The

status information is then sent to the MXL.

The OCC-1 occupies a network address.

Set the address on switch S1. When

installing an OCC-1 card, use the CSG-M

(AccuLINK) configuration printout to locate

the address of the card. Follow the switch

setting instructions in Table 1 to set the

desired address.

For additional information on the Voice

System, refer to the MXL/MXLV Manual,

P/N 315-092036.

INSTALLATION

Remove all system power before

installation, first the battery and

then AC. (To power up, connect the

AC first and then the battery.)

1. Remove the card from its protective

bag. Do not touch the gold edge of the

board.

2. Refer to the CSG-M configuration

printout for the address of the module.

Fire Safety

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

Figure 1

OCC-1 Output Control Card Module

3. Set the card address on switch S1

using dipswitches SW1-SW8.

a. Refer to Figure 1 for the location of

switch S1.

b. Refer to Table 1 for the switch

settings.

c. Set the address (See NOTE below).

NOTE: To open a dipswitch, press

down on the side of the dipswitch

marked OPEN. To close a dip-

switch, press down on the side of

the dipswitch opposite the side

marked OPEN.

To open a slide switch, push

the slide to the side opposite the

side marked ON. To close a slide

switch, push the slide to the side

marked ON.

4. There is a jumper E1 on the OCC-1.

Refer to Figure 1 for its location. If the

EL-410C/D amplifier is used, place

jumper E1 in the right-hand position.

This connects the backup amplifier

input negative side to the MXLV power

supply.

5. Switch S2 is not presently used, but it

must be left in place.

6. Do NOT install the card in its edge

connector until ALL OMM-1/-2 field

wiring is completed and checked for

shorts, opens, and other faults. Refer

to Wiring and to the OCC-1 Wiring

Checkout Chart. Replace the card in

its protective bag if the wiring is not

complete.

7. Place the user key from the installa-

tion kit in the OMM-1/-2 card edge

connector for the OCC-1 (See Figure

2). See Figure 3 for the exact location

of the key for this module. This pre-

vents installation of any other card

type in the OCC-1 slot.

CAUTION

At all times handle any plug-in

cards with extreme care. When in-

serting or removing a card, be

sure the card is kept at right

angles to the OMM board. Other-

wise, the plug-in card can damage

or displace other components.

8. Two keys to prevent reverse installa-

tion of the card are already factory

installed in the OMM-1/-2 edge con-

nectors (See Figure 3).

9. After completing and checking all field

wiring, place the card in its card edge

connector. The components on the

board must face the 22-position

terminal block where the wiring is

terminated. Press the card firmly in

place to be sure it is seated properly in

the edge connector.

WIRING

(Refer to Figure 4)

All wiring must comply with

national and local codes.

Maximum wire size:

14 AWG shielded twisted pair

Minimum wire size:

18 AWG shielded twisted pair

Maximum loop resistance:

20 ohms for both wires

End of Line Resistors

Audio risers: 10K, 1/2W, 5%

(P/N 140-820396)

Telephone risers: 5.6K, 1/2W, 5%

(P/N 140-820390)

Figure 2

Installing the User Key in the OMM

Card Edge Connector

Figure 3

Location of the User Key for the OCC-1

ELECTRICAL RATINGS

tnerruCeludoMCDV5evitcAAm01

tnerruCeludoMCDV42evitcAAm01

tnerruCeludoMCDV42ybdnatSAm51

Figure 4

Typical Riser Connections

All wiring must conform to National and Local codes.

AUDIO RISER 1 +

AUDIO RISER 1 -

AUDIO RISER 1 SHIELD

TO THE NEXT

OCC-1 IN THE

SYSTEM

FROM THE TBM

OR PREVIOUS

OCC-1 IN THE

SYSTEM

SUPERVISED, POWER LIMITED

SEE NOTES 1 AND 2

EOL

SHIELD

AUDIO

RISER 2

AUDIO

RISER 3

TELEPHONE

RISER

TO CHANNEL A AMPLIFIER 1 INPUT +

TO CHANNEL A AMPLIFIER 1 INPUT -

TO CHANNEL B AMPLIFIER 2 INPUT +

TO CHANNEL B AMPLIFIER 2 INPUT -

TO CHANNEL C AMPLIFIER 3 INPUT +

TO CHANNEL C AMPLIFIER 3 INPUT -

TERMINATE THE

SHIELD ONLY AT

THE EL-410C/D

AMPLIFIER

SUPERVISED, POWER LIMITED

PLACE AMPLIFIER INPUT AND OUTPUT CABLES

IN SEPERATE CONDUITS

SEE NOTE 4

TO TERMINAL 8,

EL-410C/D

FOR USE WITH PL864-25S ONLY

*CONNECT AN EOL ONLY IF

THIS IS THE LAST OCC-1 CARD

Notes:

1. If this OCC-1 is the last or the only OCC-1, terminate the

inputs shown as follows:

Audio risers: 10K, ½W, 5% (P/N 140-820396)

Telephone riser: 5.6K, ½W, 5% (P/N 140-820390)

2. Maximum loop resistance: 20 ohms for telephone and audio

risers.

3. Minimum wire size: 18 AWG twisted pair, shielded

Maximum wire size: 14 AWG twisted pair, shielded

4. Configure Generic input with CSG-M for either NC or NO dry

contact input or normally low or normally high 5/24 VDC input.

Generic input supervision is enabled in CSG-M for any type of

power failure.

a. Wire the NC or NO dry contact input across terminals

13 and 14.

b. Wire the normally low or normally high 5/24 VDC input

to terminal 14. (Normally low = high going input;

Normally high = low going input. The EL-410C/D power/

battery supervision is normally low input.)

5. Refer to Wiring Specification for MXL, MXL-IQ and MXLV

Systems, P/N 315-092772 revision 6 or higher, for additional

wiring information.

6. Positive and negative ground fault detected at <70K ohms

for terminals 17-22.

OCC-1 WIRING CHECKOUT CHART

Resistence

Between

Terminals

Resistance

Desired

Possible Cause of

Problem

1 to 2

4 to 5

7 to 8

10K

Line shorted

Line open

No EOL

Wrong EOL

10 to 11 5.6K

Line shorted

Line open

No EOL

Wrong EOL

1-22 to chassis > 1 Meg Short in wiring

2 to 3

3 to 4

5 to 6

6 to 7

8 to 9

9 to 10

11 to 12

12 to 13

> 1 Meg Short in wiring

17 to 18

19 to 20

21 to 22

> 1 Meg Line shorted

16 to 17

18 to 19

20 to 21

> 1 Meg Short in wiring

1ELBAT

GNIMMARGORPSSERDDAKROWTEN

RDDA12345678RDDA12345678RDDA12345678RDDA12345678

000

100

200

300

400

500

600

700

800

900

010

110

210

310

410

510

610

710

810

910

020

120

220

320

420

520

620

720

820

920

030

130

230

330

430

530

630

730

830

930

040

140

240

340

440

540

640

740

840

940

050

150

250

450

550

650

750

850

950

060

160

260

360

LAGELLI

XXOOOOOO

OOXOOOOO

XOXOOOOO

OXXOOOOO

XXXOOOOO

OOOXOOOO

OOXOOOO

OXOXOOOO

XXOXOOOO

OOXXOOOO

XOXXOOOO

OXXXOOOO

XXXXOOOO

OOOOXOOO

XOOOXOOO

OXOOXOOO

XXOOXOOO

OOXOXOOO

XOXOXO

OXXOXOOO

XXXOXOOO

OOOXXOOO

XOOXXOOO

OXOXXOOO

XXOXXOOO

OOXXXOOO

XOXXXOOO

OXXXXOOO

XXXXXOOO

OOOOOXOO

XOOOOXOO

OXO

OOXOO

XXOOOXOO

OOXOOXOO

XOXOOXOO

OXXOOXOO

XXXOOXOO

OOOXOXOO

XOOXOXOO

OXOXOXOO

XXOXOXOO

OOXXOXOO

XOXXOXOO

OXXXOXOO

XXXXOXOO

OOOOXXOO

XOOOXXOO

OXOOXXOO

XXOOXXOO

OOXOXXOO

XOXOXXOO

OXXOXXOO

XXXOXXOO

OOOXXXOO

XOOXXXOO

OXOXXXOO

XXOXX

XOO

OOXXXXOO

XOXXXXOO

OXXXXXOO

XXXXXXOO

460

560

660

760

860

960

070

170

270

370

470

570

670

770

870

970

080

180

280

380

480

580

680

780

880

980

090

190

290

390

490

590

690

790

890

990

001

101

201

301

401

501

601

701

801

901

011

111

211

311

411

511

611

711

811

021

121

221

321

421

521

621

721

OOOOOOXO

XOOOOOXO

OXOOOOXO

XXOOOOXO

OOXOOOXO

XOXOOOXO

OXXOOOXO

XXXOOOXO

OOOXOOXO

XOOX

OOXO

OXOXOOXO

XXOXOOXO

OOXXOOXO

XOXXOOXO

OXXXOOXO

XXXXOOXO

OOOOXOXO

XOOOXOXO

OXOOXOXO

XXOOXOXO

OOXOXOXO

XOXOXOXO

XXOXOXO

XXXOXOXO

OOOXXOXO

XOOXXOXO

OXOXXOXO

XXOXXOXO

OOXXXOXO

XOXXXOXO

OXXXXOXO

XXXXXOXO

OOOOOXXO

XOOOOXXO

OXOOOX

XXOOOXXO

OOXOOXXO

XOXOOXXO

OXXOOXXO

XXXOOXXO

OOOXOXXO

XOOXOXXO

OXOXOXXO

XXOXOXXO

OOXXOXXO

XOXXOXXO

OXXXOXXO

XXX

XOXXO

OOOOXXXO

XOOOXXXO

OXOOXXXO

XXOOXXXO

OOXOXXXO

XOXOXXXO

OXXOXXXO

XXXOXXXO

OOOXXXXO

XOOXXXXO

OXOXXXXO

XXOXXXXO

OOXXXXXO

XOXXXXXO

OXXXXXXO

XXXXXXXO

821

921

031

131

231

331

431

531

631

731

831

931

041

141

241

341

441

541

641

741

841

941

051

151

251

351

451

551

651

751

851

951

061

161

261

361

461

561

661

761

861

961

071

171

271

371

471

571

671

771

871

971

081

181

281

381

581

681

781

881

981

091

191

OOOOOOOX

XOOOOOOX

OXOOOOOX

XXOOOOOX

OOXOOOOX

XOXOOOOX

OXXOOOOX

XXXOOOOX

OOOXOOOX

XOOXOOO

OXOXOOOX

XXOXOOOX

OOXXOOOX

XOXXOOOX

OXXXOOOX

XXXXOOOX

OOOOXOOX

XOOOXOOX

OXOOXOOX

XXOOXOOX

OOXOXOOX

XOXOXOOX

OXXO

XOOX

XXXOXOOX

OOOXXOOX

XOOXXOOX

OXOXXOOX

XXOXXOOX

OOXXXOOX

XOXXXOOX

OXXXXOOX

XXXXXOOX

OOOOOXOX

XOOOOXOX

OXOOOXOX

XOOOXOX

OOXOOXOX

XOXOOXOX

OXXOOXOX

XXXOOXOX

OOOXOXOX

XOOXOXOX

OXOXOXOX

XXOXOXOX

OOXXOXOX

XOXXOXOX

OXXXOXOX

XXXXOX

OOOOXXOX

XOOOXXOX

OXOOXXOX

XXOOXXOX

OOXOXXOX

XOXOXXOX

OXXOXXOX

XXXOXXOX

OOOXXXOX

XOOXXXOX

OXOXXXOX

XXOXXXOX

OOX

XXXOX

XOXXXXOX

OXXXXXOX

XXXXXXOX

291

391

491

591

691

791

891

991

002

102

202

302

402

502

602

702

802

902

012

112

212

312

412

512

612

712

812

912

022

122

222

322

422

522

622

722

822

922

032

132

232

332

432

532

632

732

832

932

042

142

242

342

442

542

642

742

842

052

152

252

352

452

552

OOOOOOXX

XOOOOOXX

OXOOOOXX

XXOOOOXX

OOXOOOXX

XOXOOOXX

OXXOOOXX

XXXOOOXX

OOOXOOXX

XOOXOOXX

OXOOXX

XXOXOOXX

OOXXOOXX

XOXXOOXX

OXXXOOXX

XXXXOOXX

OOOOXOXX

XOOOXOXX

OXOOXOXX

XXOOXOXX

OOXOXOXX

XOXOXOXX

OXXOXOX

XXXOXOXX

OOOXXOXX

XOOXXOXX

OXOXXOXX

XXOXXOXX

OOXXXOXX

XOXXXOXX

OXXXXOXX

XXXXXOXX

OOOOOXXX

XOOOOXXX

OXOOOXXX

XXOO

OXXX

OOXOOXXX

XOXOOXXX

OXXOOXXX

XXXOOXXX

OOOXOXXX

XOOXOXXX

OXOXOXXX

XXOXOXXX

OOXXOXXX

XOXXOXXX

OXXXOXXX

XXXXOXXX

OOOXXXX

XOOOXXXX

OXOOXXXX

XXOOXXXX

OOXOXXXX

XOXOXXXX

OXXOXXXX

XXXOXXXX

LAGELLI

LAG

ELLI

LAGELLI

)NOro(DESOLC=X)FFOro(NEPO=O

P/N 315-090918-12

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens 3NP1 Series Bedienungsanleitung

Siemens

Siemens S-60 Bedienungsanleitung

Siemens

Siemens SIMOTION D4 Series Technisches Dokument

Siemens

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Bedienungsanleitung

Siemens

Siemens Simatic RTU3030C Bedienungsanleitung

Siemens

Siemens SINUMERIK 808D Installationsanleitung

Siemens

Siemens SINAMICS Series Technisches Dokument

Siemens

Siemens SINAMICS G130 Bedienungsanleitung

Siemens

Siemens Flowrite 599 Series Betriebsanleitung

Siemens

Siemens SCALANCE W788C-2 Bedienungsanleitung

Siemens

Siemens SINAMICS G130 Bedienungsanleitung

Siemens

Siemens Sinumerik 840DiE sl Bedienungsanleitung

Siemens

Siemens SIRIUS 3RA2712-.A Series Bedienungsanleitung

Siemens

Siemens SINAMICS S120 Technisches Dokument

Siemens

Siemens IP-Module Bedienungsanleitung

Siemens

Siemens TL-30U Bedienungsanleitung

Siemens

Siemens SIRIUS 3RW44 Bedienungsanleitung

Siemens

Siemens SIMATIC RTLS4330G Bedienungsanleitung

Siemens

Siemens SIMOTION SCOUT Merkblatt

Siemens

Siemens AZL2 Series Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Stücklistenhandbuch

Siemens

Siemens SIMOTION D410-2 Bedienungsanleitung

Siemens

Siemens HCP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Technisches Dokument

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung