Siemens RCC-2/R Bedienungsanleitung

Installation Instructions

Model RCC-2/R and RSE-1

Remote Control Centers

INTRODUCTION

The Model RCC-2/R Remote Command Center

from Siemens Industry, Inc. (See Figure 1)

provides the option to remotely annunciate and

control MXL and MXL-IQ system status. The

RCC-2/R and RSE-1 provide for mounting and

control of the PIM-1 printer interface module.

The following modules come already installed in

an RCC-2/R:

• Keypad

• LCD Display

• ANN-1 Driver Board

• PS-5N7 Power Supply

The following modules come already installed in

an RSE-1:

• ANN-1 Driver Board

• PS-5N7 Power Supply

The RCC-2/R has a mounting location for an

optional PIM-1. The RSE-1 has the same

mounting and requires the PIM-1.

The RCC-2/R comes with a clear lens on a

secure door. This limits access to the control of

the system or the display. The door is secured

with a T-45 lock set.

OPERATION

The keypad on the RCC-2/R operates the same

as the MKB in the MXL enclosure. See Section 3

of the MXL Installation, Operation and Mainte-

nance Manual, P/N 315-092036, for the com-

plete operating instructions for the control panel.

INSTALLATION

Always remove all power before installa-

tion, first the battery and then the AC.

Setting the Network Address

Before installing the RCC/RSE, set the network

address on S1-SW1 and S1-SW2 of the ANN-1

board. Refer to Table 1 for switch settings. (See

also Setting the Network Address in Section 2,

INSTALLATION of the MXL/MXLV Manual, P/N

315-092036.)

TABLE 1

SWITCH SETTINGS ON THE ANN-1

SWITCH

ADDRESS SETTINGS FOR:

248 249 250 251

S1-SW1 Open-

OFF Closed-

ON Open-

OFF Closed-

S1-SW2 Open-

OFF Open-

OFF Closed-

ON Closed-

S1-SW3 Closed-

ON Closed-

S1-SW4 Closed-

ON Closed-

S1-SW5 Closed-

ON Closed-

NOTE: Switches S1-SW3 and S1-SW4 are for

future use. Switch S1-SW5 is used to

select supervision.

Figure 1

RCC-2/R Remote Command Center

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

P/N 315-099160-8

Setting Supervision

Use switch S1-SW5 on the ANN-1 to select or

deselect supervision. If your ANN-1 has a switch

with position 1 indicated on the left-hand side,

ignore the printing on the switch. SW1 on S1 is at

the extreme right-hand side of S1, regardless of

any other marking.

To set for supervision

S1-SW5 = Closed (ON)

To set for non-supervision

S1-SW5 = Open (OFF)

NOTE: When you select non-supervision for

an annunciator, there must also be

one and only one supervised annun-

ciator at the same address.

Mounting

Before mounting the RCC/RSE, follow these

steps:

1. Remove the cover assembly from the

backbox.

2. Disconnect at P1 the cable from the PS-5N7.

3. Remove the PS-5N7 from the backbox (See

Figures 2 and 3).

4. Set the panel to one side.

Consider the following when mounting the

backbox:

• Mounting height for visual and manual

access to the keypad

• Weight and size of the enclosure

• Local mounting codes

To mount the RCC/RSE, follow these steps:

1. Fasten the RCC/RSE backbox securely to a

clean, dry, shock-free, and vibration-free

surface using the four mounting holes

provided. (Refer to Figure 4 for the

dimensions of the backbox and the location

of the mounting holes.) Position the RCC/

RSE backbox clear of obstructions so that

the door opens freely and the indicators and

controls are easily accessible.

2. Pull all field wiring into the backbox and

dress the wiring to the approximate location

to which it will go. Install field wiring to the

PS-5N7 (Refer to PS-5N7 Installation

Instructions,

P/N 315-092729).

3. If a PIM-1 is required, mount it to the set of

four standoffs to the right of the PS-5N7

(See Figures 2 and 3).

Connect P1 on the PIM-1 to P1 on the ANN-1,

using the 14 inch cable, P/N 555-192242.

Connect P2 on the PIM-1 to P1 on the PS-5N7,

using the 14 inch cable, P/N 555-192242

(Refer to PS-5N7 Installation Instructions,

P/N 315-092729, PIM-1 Installation

Instructions, P/N 315-091462 and Figure 6).

4. If a PIM-1 is not installed, reconnect P1 on

the ANN-1 to P1 on the PS-5N7.

5. Reattach the cover assembly to the

backbox.

6. Refer to the MXL/MXLV Manual, P/N 315-

092036, for additional information on the

operation of the keypad.

ELECTRICAL RATINGS

Refer to the following Installation Instructions as

needed:

MMB-2 P/N 315-095097

MMB-3 P/N 315-048860

PSR-1 P/N 315-090911

PS-35 P/N 315-085062

PLM-35 P/N 315-093495

PAD-3 P/N 315-099082

SMB-2 P/N 315-095931

MXL/MXLV Manual P/N 315-092036

WIRING

tnerruCeludoMCDV5evitcAAm0

eludoMCDV42evitcA tnerruC Am51+Am56 desusi1-MIPfi

eludoMCDV42ybdnatS tnerruC Am51+Am56 desusi1-MIPfi

Figure 2

RCC-2/R Exploded View

LCD DISPLAY

ANNUNCIATOR

PANEL

COVER PIM-1

(OPTIONAL)

ANN-1

RCC-2/RSE-1

OUTER DOOR

RCC-2/RSE-1

BACKBOX

PS-5N7

PIM-1

(REQUIRED)

ANN-1

RSE-1 OUTER DOOR

RSE-1

BACKBOX

PS-5N7

Figure 3

RSE-1 Exploded View

Notes:

1. Use a minimum wire gauge of 18 AWG.

2. Use a maximum of 80 ohms per pair of

wires for the network connections.

3. Use shielded twisted pair for network

connections.

4. Terminate the shield ONLY at the MMB/SMB

enclosure.

5. PSR-1 only allowed in systems with MMB-2.

Figure 5

PS-5N7 Power Supply and Network Wiring Diagram in RCC/RSE Enclosure (Style 4)

654321

PS-5N7

(INSTALLED IN AN

RCC-2/RSE-1

ENCLOSURE)

TB1

TB4

EOLR 120 OHMS

1/4W, 5%

P/N 140-820150

DO NOT USE

PSR-1

TB4

EOLR

CHASSIS

SHIELD

MMB-2 / SMB-2

EOLR 120 OHMS

1/4W, 5%

P/N 140-820150

EOLR

Figure 4

RCC-2/R, RSE-1 Dimensions

NOTE: The RCC/RSE MUST have an earth ground connected to the chassis. Wire shield or conduit is

not an acceptable ground. Use any available unused, unpainted stud for chassis grounding.

6. DO NOT place the PS-5N7 at the end of

the network (Style 7 only).

7. This configuration is power limited to NFPA

70 according to NEC 760.

8. All wiring supervised.

9. Refer to Wiring Specification for MXL, MXL-IQ

and MXLV Systems, P/N 315-092772 revision

6 or higher, for additional wiring information.

10. MNET: Maximum voltage: 8V peak to peak

Maximum current: 150mA

MAKE THIS CONNECTION TO ANY

OF THE FOLLOWING TERMINATIONS:

MMB

SMB

PSR-1

PLM-35

(Used with PS-35)

ALARMSAF

(Model BN4-002-UL)

PAD-3

TB5, 9-12

TB3, 3-6

TB1, 1-2

DC1

TB2, 18-19

MOM-4

TB1 P5

TB6

PSR-1

TB4

P7 FOR

NET-7

1234

NET-7

CABLE P/N 555-190967

MMB-2 / SMB-2

POWER

TO MOM-4

TB1

CABLE

P/N 600-290505

CHASSIS

SHIELD

123 4 5 6 7 8 9 10 11 12 13 14 16

EOLR

120 OHM,

1/4W, 5%

P/N 140-820150

NETWORK A (PRIMARY)

SUPERVISED

POWER LIMITED

NETWORK B (SECONDARY)

SUPERVISED

POWER LIMITED

+24 VDC

-24 VDC RETURN

SUPERVISED

POWER LIMITED

RCC-2 / RSE-1

PS-5N7

(INSTALLED IN AN

RCC-2/RSE-1

ENCLOSURE)

TB1

TB2

Figure 6

PS-5N7 Power Supply and Network Wiring Diagram in RCC/RSE Enclosure (Style 7)

Notes:

1. Use a minimum wire gauge of 18 AWG.

2. Use a maximum of 80 ohms per pair of

wires for the network connections.

3. Use shielded twisted pair for network

connections.

4. Terminate the shield ONLY at the MMB/SMB

enclosure.

5. PSR-1 only allowed in systems with MMB-2.

6. DO NOT place the PS-5N7 at the end of

the network (Style 7 only).

7. This configuration is power limited to NFPA

70 according to NEC 760.

8. Refer to Wiring Specification for MXL, MXL-IQ

and MXLV Systems, P/N 315-092772 revision 6

or higher, for additional wiring information.

9. MNET: Maximum voltage: 8V peak to peak

Maximum current: 150mA

This page is intentionally blank.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

P/N 315-099160-8

This page is intentionally blank.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens SIMATIC S7 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RV2.2 Bedienungsanleitung

Siemens

Siemens SINUMERIK 802D Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens WFZ661 Installations- und Betriebshandbuch

Siemens

Siemens VRD Series Betriebsanleitung

Siemens

Siemens MICROMASTER 420 Bedienungsanleitung

Siemens

Siemens SIMATIC Bedienungsanleitung

Siemens

Siemens SENTRON PAC RS485 Bedienungsanleitung

Siemens

Siemens SINAMICS G130 Bedienungsanleitung

Siemens

Siemens SENTRON Series Bedienungsanleitung

Siemens

Siemens MJ-4 Series Bedienungsanleitung

Siemens

Siemens SIPROTEC 7SJ61 Gebrauchsanweisung

Siemens

Siemens SIPLUS CMS4000 IFN VIB-A Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens SITRANS RD500 Bedienungsanleitung

Siemens

Siemens XT55 GPS Startup Bedienungsanleitung

Siemens

Siemens SIMATIC 6DL1 136-6AA00-0PH1 Bedienungsanleitung

Siemens

Siemens 3RK2 Series Bedienungsanleitung

Siemens

Siemens SIMOTION D425-2 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D Stücklistenhandbuch

Siemens

Siemens SINUMERIK 808D Kurzanleitung

Siemens

Siemens EcoView Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung