Siemens CU240E-2 Bedienungsanleitung

___________________

SINAMICS

SINAMICS G120

CU240B-2 and CU240E-2 Control

Units

Compact Operating Instructions

Edition 01/2017

01/2017

A5E39910322B AA

Fundamental safety

instructions

Scope of delivery

Installing

Commissioning

More information

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E39910322B AA

Ⓟ

01/2017 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CU240B-2 and CU240E-2 Control Units

Compact Operating Instructions, 01/2017, A5E39910322B AA 3

Table of contents

1 Fundamental safety instructions.............................................................................................................. 4

1.1 General safety instructions .......................................................................................................4

1.2 Industrial security ......................................................................................................................5

2 Scope of delivery .................................................................................................................................... 6

3 Installing ................................................................................................................................................. 7

3.1 Plugging the Control Unit onto the Power Module....................................................................7

3.2 Overview of the interfaces ........................................................................................................9

3.3 Terminal strips on CU240B-2 Control Units............................................................................11

3.4 Factory setting of the CU240B-2 interfaces............................................................................13

3.5 Terminal strips on CU240E-2 Control Units............................................................................15

3.6 Factory setting of the CU240E-2 interfaces............................................................................17

4 Commissioning ..................................................................................................................................... 19

4.1 Tools to commission the converter .........................................................................................19

4.2 Commissioning with BOP-2 operator panel............................................................................20

4.2.1 Quick commissioning with the BOP-2.....................................................................................20

4.2.2 Standard Drive Control ...........................................................................................................22

4.2.3 Dynamic Drive Control............................................................................................................24

4.2.4 Identifying the motor data and optimizing the closed-loop control .........................................26

4.3 Connecting the inverter to the fieldbus ...................................................................................28

4.4 Frequently required parameters .............................................................................................30

5 More information................................................................................................................................... 33

5.1 Overview of the manuals ........................................................................................................33

5.2 Technical support....................................................................................................................34

This manual describes how you install the CU240B-2 or CU240E-2 Control Unit of the

SINAMICS G120 inverter and commission it.

What is the meaning of the symbols in the manual?

Reference to further information in the manual

An operating instruction starts here.

This concludes the operating instruction.

Download from the Internet

DVD that can be ordered

CU240B-2 and CU240E-2 Control Units

4 Compact Operating Instructions, 01/2017, A5E39910322B AA

Fundamental safety instructions

1.1

General safety instructions

WARNING

Danger to life if the safety instructions and residual risks are not observed

If the safety instructions and residual risks in the associated hardware documentation are

not observed, accidents involving severe injuries or death can occur.

•Observe the safety instructions given in the hardware documentation.

•Consider the residual risks for the risk evaluation.

WARNING

Danger to life or malfunctions of the machine as a result of incorrect or changed

parameterization

As a result of incorrect or changed parameterization, machines can malfunction, which in

turn can lead to injuries or death.

•Protect the parameterization (parameter assignments) against unauthorized access.

•Respond to possible malfunctions by applying suitable measures (e.g. EMERGENCY

STOP or EMERGENCY OFF).

Fundamental safety instructions

1.2 Industrial security

CU240B-2 and CU240E-2 Control Units

Compact Operating Instructions, 01/2017, A5E39910322B AA 5

1.2

Industrial security

Note

Industrial security

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber

threats, it is

necessary to implement

– and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens products and solutions only represent one component of such a

concept.

The customer is responsible for preventing unautho

rized access to its plants, systems,

machines and networks. Systems, machines and components should only be connected to

the enterprise network or the internet if and to the extent necessary and with appropriate

security measures (e.g. use of firewalls and

network segmentation) in place.

Additionally, Siemens’ guidance on appropriate security measures should be taken into

account. For more information about industrial security, please visit:

Industrial security (

http://www.siemens.com/industrialsecurity).

Siemens’ products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends to apply product updates as soon as available and to

always use the latest product versions. Use of product versions that are no longer supported,

and failure to apply latest updates may increase customer’s exposure to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed at:

ndustrial security (http://www.siemens.com/industrialsecurity).

WARNING

Danger to life as a result of unsafe operating states resulting from software manipulation

Software manipulations (e.g. viruses, trojans, malware or worms) can cause unsafe

operating states in your system that may lead to death, serious injury, and property

damage.

•Keep the software up to date.

•Incorporate the automation and drive components into a holistic, state-of-the-art

industrial security concept for the installation or machine.

•Make sure that you include all installed products into the holistic industrial security

concept.

•Protect files stored on exchangeable storage media from malicious software by with

suitable protection measures, e.g. virus scanners.

CU240B-2 and CU240E-2 Control Units

6 Compact Operating Instructions, 01/2017, A5E39910322B AA

Scope of delivery

The delivery comprises at least the following components:

●A CU240B-2 or a CU240E-2 control unit with firmware, which is ready to run. Options for

upgrading and downgrading the firmware can be found on the Internet: Firmware

(http://support.automation.siemens.com/WW/news/en/67364620)

The fieldbus interface of the Control Unit depends on the Article No. The Article No., the

designation and the version of the hardware (e.g. 02) and firmware (e.g. 4.6) can be

found on the rating plate ①of the Control Unit.

Designation

Article number

Fieldbus

CU240B-2

6SL3244-0BB00-1BA1

USS, Modbus RTU

CU240B-2 DP

6SL3244-0BB00-1PA1

PROFIBUS DP

CU240E-2

6SL3244-0BB12-1BA1

USS, Modbus RTU

CU240E-2 F

6SL3244-0BB13-1BA1

CU240E-2 DP

6SL3244-0BB12-1PA1

PROFIBUS DP

CU240E-2 DP-F

6SL3244-0BB13-1PA1

CU240E-2 PN

6SL3244-0BB12-1FA0

PROFINET IO, EtherNet/IP

CU240E-2 PN-F 6SL3244-0BB13-1FA0

●Compact Operating Instructions in German and English

●The inverter contains open-source software (OSS). The OSS license terms are saved in

the inverter.

Transferring OSS license terms to a PC

Procedure

To transfer OSS license terms to a PC, proceed as follows:

1. Switch off the inverter power supply.

2. Insert an empty memory card into the card slot of the inverter.

Overview of the interfaces (Page 9)

3. Switch on the inverter power supply.

4. The inverter writes file "Read_OSS.ZIP" to the memory card within approximately

30 seconds.

5. Switch off the inverter power supply.

6. Withdraw the memory card from the inverter.

7. Insert the memory card into the card reader of a PC.

8. Please read the license terms.

You have transferred the OSS license terms to a PC.

CU240B-2 and CU240E-2 Control Units

Compact Operating Instructions, 01/2017, A5E39910322B AA 7

Installing

3.1

Plugging the Control Unit onto the Power Module

Permissible Power Modules

You may operate the Control Unit with the following Power Modules:

Power Module

✓= operation with Power Module permissible, --- = not per-

missible

CU240B-2

CU240E-2

PM230 IP20 and push-through

✓

PM230 IP55 --- ✓

PM240P-2

✓

PM240-2 ✓✓

PM250

✓

Installing the Control Unit - General

Each Power Module has an appropriate holder for the Control Unit and a release

mechanism.

Inserting the Control Unit

Proceed as follows to plug the Control

Unit onto a Power Module:

Place the two catches of the

Control Unit in the matching

grooves of the Power Module.

Press the Control Unit onto the

Power Module until you hear that it

latches.

You have now plugged the Control

Unit onto the Power Module.

Removing the Control Unit

Remove the Control Unit from the Power Module by pressing the release mechanism.

Installing

3.1 Plugging the Control Unit onto the Power Module

CU240B-2 and CU240E-2 Control Units

8Compact Operating Instructions, 01/2017, A5E39910322B AA

Special features for the PM230 Power Module IP55, FSA … FSC

To insert or detach the Control Unit, you must

release eight

or ten fixing screws of the cover

and then remove the cover.

The Power Module release mechanism is

shown in the diagram.

Attach the cover again before you commission

the inverter. Do not damage the seal of the

cover when attaching it.

Adapter for operating a PM230 IP55 Power Module

For operating the Control Unit with a PM230 IP55 Power Module, FSA … FSC, an adapter is

required between the Control Unit and operator panel (BOP-2 or IOP).

The adapter, which is included in the scope of delivery of the Power Module, is too short for

the CU240E-2 Control Unit. The matching adapter for the CU240E-2 Control Unit can be

ordered through the KnorrTec company.

Article number 10055500

Figure 3-1 Insert the KnorrTec adapter on the interface for the operator panel

Installing

3.2 Overview of the interfaces

CU240B-2 and CU240E-2 Control Units

Compact Operating Instructions, 01/2017, A5E39910322B AA 9

3.2

Overview of the interfaces

Interfaces at the front of the Control Unit

To access the interfaces at the front of the Control Unit, you must lift the Operator Panel (if

one is being used) and open the front doors.

①

Memory card slot

②

Terminal strips

③

Bus termination, only for

USS and Modbus field

buses

④

Fieldbus interface at the lower side

⑤

Selecting the fieldbus

address

On all Control Units with

the exception of

CU240E

-2 PN and

CU240E

-2 PN-F

⑥

Status

LED

⑦

USB interface for connection to a PC

⑧

Switch for AI

0 and AI 1 1)

(U/I)

•

I0/4 mA … 20 mA

•

U -10/0 V … 10 V

⑨

Interface to the operator panel

1) AI 1 is not available on the CU240B-2 Control Unit

Table 3- 1 Number of inputs and outputs

Digital

inputs DI

Digital

outputs DO

Analog

inputs AI

Analog

outputs AO

Fail-safe digital

inputs F-DI 1)

CU240B-2, CU240B-2 DP

CU240E-2, CU240E-2 DP,

CU240E-2 PN

6 3 2 2 1

CU240E-2 F, CU240E-2 DP-F,

CU240E-2 PN-F

6 3 2 2 3

1) Each fail-safe digital input F-DI used takes up two digital inputs DI

Installing

3.2 Overview of the interfaces

CU240B-2 and CU240E-2 Control Units

10 Compact Operating Instructions, 01/2017, A5E39910322B AA

Table 3- 2 Permissible cable and wiring options

Solid or flexible conduc-

tors

Finely stranded con-

ductor with non-

insulated end sleeve

Finely stranded con-

ductor with partially

insulated end sleeve

Two finely stranded

conductors with the

same cross-section

with partially insulated

twin end sleeves

Wiring the terminal strip in compliance with EMC

●If you use shielded cables, then you must connect the shield to the mounting plate of the

control cabinet or with the shield support of the inverter through a good electrical

connection and a large surface area.

●Use the shield connection plate of the Control Unit as shield support and strain relief.

Table 3- 3 Article numbers

Shield connection kit 2 for the CU240B-2 and CU240E-2 Control Units with

all fieldbus interfaces except for PROFINET.

6SL3264-1EA00-0HA0

Shield connection kit 3 for the CU230P-2 and CU240E-2 Control Units with

PROFINET interface

6SL3264-1EA00-0HB0

Additional information about EMC-compliant wiring is available on the Internet: EMC

installation guideline (http://support.automation.siemens.com/WW/view/en/60612658)

Interfaces at the lower side of the CU240B-2 and CU240E-2 Control Units

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens SQK349.00/209 Bedienungsanleitung

Siemens

Siemens SIMATIC NET SCALANCE WLC711 Bedienungsanleitung

Siemens

Siemens RWD68 Bedienungsanleitung

Siemens

Siemens SIPART DR19 Bedienungsanleitung

Siemens

Siemens Simatic S7-300 Bedienungsanleitung

Siemens

Siemens Simatic S7-300 Bedienungsanleitung

Siemens

Siemens SIMATIC 500 Bedienungsanleitung

Siemens

Siemens ST750 Bedienungsanleitung

Siemens

Siemens SIMATIC S5-90U Benutzerhandbuch

Siemens

Siemens AVS75.39 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Betriebsanleitung

Siemens

Siemens SQM40 Series Bedienungsanleitung

Siemens

Siemens SIDOOR AT40 Benutzerhandbuch

Siemens

Siemens MVI421 Series Bedienungsanleitung

Siemens

Siemens Flowrite 599 Series Bedienungsanleitung

Siemens

Siemens RXB39.1 Bedienungsanleitung

Siemens

Siemens SIMATIC S5 Series Bedienungsanleitung

Siemens

Siemens LOGO! 0BA7 Bedienungsanleitung

Siemens

Siemens SIMATIC HMI TP700 Comfort Bedienungsanleitung

Siemens

Siemens SIMATIC S5 Bedienungsanleitung

Siemens

Siemens IQHeat Bedienungsanleitung

Siemens

Siemens Simatic S7-300 Bedienungsanleitung

Siemens

Siemens REA23M Bedienungsanleitung

Siemens

Siemens SIRIUS ET 200S Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung