Siemens HMS-2S Bedienungsanleitung

Siemens Industry, Inc.

BuildingTechnologies Division

P/N 315-033430-6

INTRODUCTION The Model HMS-2S/-SA Manual Station from Siemens

Industry, Inc., is a field installed addressable device

containing advanced control panel communication

technology. This technology, which provides two-

direction communication with the control panel,

produces an Intelligent Initiating Device.

PROGRAMMING Refer to Figure 1 to locate the opening on the HMS cover that allows access to the

programming holes which are on the HMS printed

circuit board.

To connect the HMS to the DPU Programmer/Tester,

insert the plug from the DPU cable provided with the

Programmer/Tester into the opening on the HMS as

shown in Figure 2. Because HMS devices are polarity

insensitive, the programming plug can be inserted into

the programming holes in either direction.

To prevent potential damage to the DPU DO NOT

connect an HMS to the DPU until at least one wire is

removed from terminals 1 or 2 of the HMS.

Follow the instructions in the DPU Manual (P/N 315-033260) to program the HMS to

the desired address. Record the device address on the label located on the HMS

front panel.The HMS can now be installed and wired to the system.

OPERATION The HMS manual station operates with the FireFinder-XLS Control Panel via the DLC

Device Loop Card.

The HMS-2S/-SA manual station housing has a pull down lever that locks in position

after releasing a spring loaded switch. (See Figure 4.) To indicate the manual station is

activated, the pull down lever remains down and locked until the station is physically

reset.The HMS-2S/-SA manual station has a set of normally closed auxiliary contacts

which are available for releasing door holders and magnetic door locks.

The HMS-2S has a keyswitch which can activate a second address.

The unit is reset by opening the hinged housing cover with an Allen key and then

closing and locking the cover, or by returning the keyswitch to its original position.

Figure 1

HMS Cover

Dual Stage Manual Pull Station (For Canadian Two-Stage Applications)

Single Stage Manual Pull Station with Auxiliary Contacts

Installation Instructions

Models HMS-2S / HMS-SA

OPENING TO

PROGRAMMING

POINTS

PLUG FROM

DPU

LOCATING TAB

PROGRAMMING

POINTS

Figure 2

Connecting the DPU Plug

INSTRUCTIONS

3½ INCH DEEP

SWITCH BOX

(USER SUPPLIED)

MODEL

MC-5

BACKPLATE

SURFACE

MOUNTING

ENCLOSURE

FLUSH

MOUNTING

ENCLOSURE

HOUSING HINGED

TO BACKPLATE

HOUSING

LOCKING

SCREW

KEYSWITCH

5½ in.

3 in.

4 in.

2¾ in.

3½ in.

NAMEPLATE

WIRING

The use of limited energy cable is not allowed.

INSTALLATION Distribute the manual station boxes throughout the protected area so that they

are unobstructed, readily accessible, and located in the normal exit path. Place the

manual station according to the regulations of the authorities having jurisdiction.

Surface Mounting Mount the backplate to a Model MC-5 Backbox as shown in Figure 4.

Flush Mounting Mount the backplate to a user supplied single gang switchbox as shown in Figure 4.

Do not overtighten the screws. Overtightening may distort the backplate.

Figure 4

Mounting The HMS

Figure 3

HMS-2S / HMS-SA Wiring Information

PROGRAMMABLE

N/C AUX CONTACT

24 VDC, 2A

(DOOR HOLDER OR

A MAGNETIC LOCK

RELEASE, ETC.)

ONLY CONNECT TO

POWER LIMITED SOURCE

PIGTAIL LEADS

TO NEXT ADDRESSABLE DEVICE

DLC LINE 1

DLC 1LINE

DLC 2LINE

EARTH GROUND

FROM INITIATING CONTROL PANEL

OR PREVIOUS ADDRESSABLE DEVICE

NOTES:

1. Recommended wire sizes:

18 AWG minimum, 14 AWG maximum

2. Wire larger than 14 AWG can damage the connector.

3. When using shielded cable without metal raceway or with

nonmetallic raceway, the shields should be terminated at the device

ground terminal. If the device box is already grounded by another

means, such as being mounted to a grounded structure, the wire

shields should be continuous and must be grounded solely at the point

of origin; for example, at the control panel.

4. When using shielded cable with metal raceway, the wiring shields

shall be continuous and grounded solely at the point of origin.The

device ground terminal shall be connected to the grounded device box.

5. When using metal raceway without shielded cable, connect the

device ground terminal to the grounded device box.

6. Metal raceway should be thoroughly grounded throughout the system.

7. Addressable Device Loop ratings:

Voltage: 31V max.

18V min. (pulsing)

Current maximum: 1mA

In supervisory: HMS-2S / HMS-SA draws 1mA.

8. The HMS-2S / HMS-SA is a polarity insensitive device. Line 1 and Line 2

can be either line of the loop.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

P/N 315-033430-6

ELECTRICAL RATINGS

pooLCLD-SF/CLD

tnerruC.xaMAm1

Dieses Handbuch passt für folgende Modelle

Andere Siemens Controller Handbücher

Siemens

Siemens Simatic S7 Series Benutzerhandbuch

Siemens

Siemens 1PL618 Series Bedienungsanleitung

Siemens

Siemens SQD Series Bedienungsanleitung

Siemens

Siemens SIRIUS 3SE5000-0A Series Bedienungsanleitung

Siemens

Siemens REV23.03RF Bedienungsanleitung

Siemens

Siemens MO310 Bedienungsanleitung

Siemens

Siemens OpenAir GDB111.1E/KN Bedienungsanleitung

Siemens

Siemens GIB 1 Series Bedienungsanleitung

Siemens

Siemens GEB-1E Series Bedienungsanleitung

Siemens

Siemens SQM5 Series Betriebsanleitung

Siemens

Siemens Simatic SM331 Bedienungsanleitung

Siemens

Siemens ACVATIX G B111.9E/KN Series Bedienungsanleitung

Siemens

Siemens OpenAir GBB161.1U Betriebsanleitung

Siemens

Siemens SIPART DR19 Bedienungsanleitung

Siemens

Siemens SIMOVERT MASTERDRIVES MC Series Bedienungsanleitung

Siemens

Siemens SITRANS LUT400 Benutzerhandbuch

Siemens

Siemens SIMATIC S7-400H Bedienungsanleitung

Siemens

Siemens RVL479 Bedienungsanleitung

Siemens

Siemens RLU2 Series Bedienungsanleitung

Siemens

Siemens SQM5 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 810D Merkblatt

Siemens

Siemens Sirius 3RA6 Benutzerhandbuch

Siemens

Siemens SIMATIC S7-200 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Benutzerhandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung