Siemens OpenAir GCA Series Betriebsanleitung

OpenAir™

Technical Instructions

Document No. 155-173P25

EA GCA-1

May 19, 2014

GCA Series Spring Return 160 lb-in

Electronic Damper Actuators

Siemens Industry, Inc.

Description The OpenAir 24 Vac/dc spring return 160 lb-in (18 Nm) electronic actuator is designed for

digital or analog control of building HVAC dampers.

Features •Brushless DC motor technology with stall protection

•Bi-directional fail-safe spring return

•Patented self-centering shaft coupling

•Manual override

•160 lb-in (18 Nm) torque

•5° preload as shipped from factory

•Offset and span adjustment models available

•Models with independently adjustable dual auxiliary switches available

•UL and cUL listed; certified

Application These actuators are designed for use in constant or variable air volume installations for the

control of return air, mixed air, exhaust, and face and bypass dampers requiring up to

160 lb-in (18 Nm) torque. They are designed for applications that require the damper to

return to a fail-safe position when there is a power failure.

Technical Instructions OpenAir™ GCA Series Spring Return 160 lb-in Electronic Damper Actuator

Document No. 155-173P25

May 19, 2014

Page 2 Siemens Industry, Inc.

Product Numbers

Table 1.

Operating

Voltage

Control Cables

Built-in Control

Options

Product

Number

24 Vac ± 20%

24 Vdc ±10%

120 Vac ± 10%

0 to 10 Vdc

2 to 10 Vdc or

0 to 10 Vdc

Floating

2-position

Standard

Plenum

Position

Feedback

Dual Auxiliary

Switches

Signal Inversion

Offset 0 to 5 Vdc

Span 2 to 30 Vdc

GCA121.1U

●

GCA121.1P

●

GCA126.1U ●

●

●●●

GCA126.1P

●

GCA221.1U

●

GCA226.1U

●

GCA131.1U

●

GCA131.1P

●

GCA132.1U ●●●●●

GCA136.1U

●

GCA136.1P

●

GCA151.1U

●

GCA151.1P ●●●●

●

GCA156.1U

●

GCA156.1P

●

GCA161.1U ●

●

●●

●

GCA161.1P ●

●

●●

●

GCA163.1U

●

GCA163.1P

●

GCA164.1U ●

●

●●

GCA164.1P

●

GCA166.1U

●

GCA166.1P ●

●

●●

●

Warning/Caution Notations

WARNING:

Personal injury/loss of life may occur if you do not

perform a procedure as specified.

CAUTION:

Equipment damage may occur if you do not

perform a procedure as specified.

OpenAir™ GCA Series Spring Return 160 lb-in Electronic Damper Actuator Technical Instructions

Document No. 155-173P25

May 19, 2014

Siemens Industry, Inc. Page 3

Specifications

Ambient

Conditions

Ambient temperature

operation -25°F to 130°F (-32°C to 55°C)

storage and transport -40°F to 158°F (-40°C to 70°C)

Ambient humidity (non-condensing) 95% rh

Agency

Certification

Conformity

UL listed to UL60730

(to replace UL873)

cUL certified to Canadian Standard

C22.2 No. 24-93

Electromagnetic compatibility (EMC) 2004/108/EC

Immunity for all models, except GCA132.xx EN61000-6-2

Immunity for GCA132.xx EN61000-6-1

Emissions for all models EN61000-6-3

Power

Supply

GCA16x GCA15x GCA13x GCA12x GCA22x

24 Vac ± 20%

24 Vdc ± 10%

24 Vac ± 20%

24 Vdc ± 10%

24 Vac± 20%

24 Vdc ± 10%

24 Vac ±

20%

24 Vdc ±

10%

120 Vac ±

10%

—

Frequency

50/60 Hz

Power Consumption

running 7 VA/5W 7 VA/5W 7 VA/5W 7 VA/5W 8 VA

holding

5 VA/3W

6 VA

Control Signal

GCA16x

GCA15x

GCA13x

GCA12x

GCA22x

Input Signal

(Y–G0)

voltage input

0 to 10 Vdc

(max. 35 Vdc)

0 to 10 Vdc or

2 to 10 Vdc

(max. 35 Vdc)

Floating

2-Position

input resistance

>100K ohms

—

Feedback

Signal

GCA16x

GCA15x

GCA13x

GCA12X

GCA22x

Position output signal

(U-G0)

voltage output

0 to 10 Vdc

0 to 1000 ohms

<10 Ma

(GCA 132x only)

Load <1W

—

maximum output

current

±1 mA

+1 mA,

-.5 mA

—

Function

Running/spring return torque

Operating with 24 Vac 160 lb-in (18 Nm)

Maximum torque <360 lb-in (40 Nm)

Runtime for 90°

operating with motor 90 sec

closing (on power loss) with spring return 15 seconds typical

NOTE: At -25°F, spring return is 142 lb-in (16 Nm).

Equipment rating

Class 2, in accordance with UL/CSA

Technical Instructions OpenAir™ GCA Series Spring Return 160 lb-in Electronic Damper Actuator

Document No. 155-173P25

May 19, 2014

Page 4 Siemens Industry, Inc.

Specifications,

Continued

Mounting

Nominal angle of rotation 90°

Maximum angular rotation 95°

Shaft size 3/8-inch to 1-inch

(8 mm to 25.6 mm) diameter

1/4-inch to 5/8-inch

(6 to 18 mm) square

Minimum shaft length 3/4-inch (20 mm)

Auxiliary features

Control signal adjustment

Offset (start point) 0 Vdc to 5 Vdc

Factory setting 0 Vdc

Span 2 Vdc to 30 Vdc

Dual auxiliary switches

AC rating (Standard cable) 24 Vac to 250 Vac

AC 6A resistive

AC 2A FLA, 12 LRA

AC rating (Plenum cable) 24 Vac

AC 4A resistive

AC 2A, FLA, 12 LRA

DC rating (Standard/Plenum cable) 12 Vdc to 30 Vdc

DC 2A

Switch Range

Switch A 0 to 90° with 5° intervals

Recommended range usage 0 to 45°

Factory setting 5°

Switch B 0 to 90° with 5° intervals

Recommended range usage 45° to 90°

Factory setting 85°

Switching hysteresis 2°

WARNING:

Apply only AC-line voltage from the same phase or only UL-Class 2 voltage to

the switching outputs of both auxiliary switches A and B. Mixed operation is not

permissible.

NOTE: With plenum cables, only UL-Class 2 voltage is permitted.

Housing

Enclosure NEMA 2, IP54 per EN 60 529

in vertical to horizontal 90°

See Figure 17.

NEMA 3R rated when installed with

ASK75.1U Weather Shield in the

vertical position. See Figure 18.

See Accessories, Figure 9.

Material Die-cast aluminum alloy

Gear lubrication Silicone-free

OpenAir™ GCA Series Spring Return 160 lb-in Electronic Damper Actuator Technical Instructions

Document No. 155-173P25

May 19, 2014

Siemens Industry, Inc. Page 5

Miscellaneous

Pre-cabled connection 18 AWG

Cable length 3 feet (0.9 m)

Noise level <45 dBA (running)

Life cycle Designed for over 60,000 full strokes

and a minimum of 1.5 million

repositions at rated torque and

temperature.

Dimensions See Figure 31.

Weight 4.85 lb (2.2 kg)

Actuator

Components

Figure 1. Modulating GCA Actuator.

NOTE: Not all features are on all models.

See Table 1for a listing of features per

model.

Legend

1. Positioning scale for angle of

rotation

2. Manual override wrench

opening and direction of

rotation arrow

3. DIP switches

4. Span adjustment

5. Offset (start point) adjustment

6. Gear train lock pin

7. Auxiliary switch B

8. Auxiliary switch A

9. Position indicator

10. Self-centering shaft adapter

11. Shaft adapter locking clip

12. Position indicator adapter

13. Mounting bracket

14. Connection cables

Technical Instructions OpenAir™ GCA Series Spring Return 160 lb-in Electronic Damper Actuator

Document No. 155-173P25

May 19, 2014

Page 6 Siemens Industry, Inc.

Accessories NOTE: The control signal adjustment cannot be added in the field. Order the

product number that includes the option(s).

Figure 2. Floor Mount Kit.

ASK71.1U: Allows foot mounting of OpenAir

actuators. Should be used for in-the-air stream

applications, and generally, anywhere a foot-

mounted actuator can be mounted. Kit contains:

•Crank arm for changing angular rotation into

a linear stroke.

•Support bearing ring to minimize side

loading on the actuator’s output bearing.

•Mounting bracket.

•Required mounting fasteners.

Figure 3. Frame Mount Kit.

ASK71.2U: Allows mounting OpenAir actuators

directly to damper frame. Should be used with

louvers and vents and in applications where floor

mount kit is not possible. Kit contains:

•Crank arm for changing angular rotation into

a linear stroke.

•Support bearing ring to minimize side

loading on the actuator’s output bearing.

•Mounting bracket.

•Required mounting fasteners.

Figure 4. Crank Arm Kit.

ASK71.3: Allows direct-coupled actuator to

provide an auxiliary linear drive. Crank arm kit

can be used to simultaneously drive a set of

opposing or adjacent dampers with single

actuator. Kit includes:

•Crank arm to attach to the splined hub of the

shaft adapter.

•Other required mounting fasteners.

Figure 5. Crank Arm Kit with

Mounting Bracket.

ASK71.4: Allows economical mounting of

OpenAir actuator to a variety of surfaces. Kit

should be used in applications where the

actuator can be rigid-surface mounted and linear

stroke output is required. Kit includes:

•Crank arm to attach to the splined hub of the

shaft adapter.

•Mounting bracket.

•Other required mounting fasteners.

Figure 6. Tandem Mount

Bracket.

ASK73.1: Bracket provides an extended anti-

rotation pin allowing two OpenAir actuators to

directly drive a single damper shaft. Tandem

mounting bracket for two GCA 2-position and

floating control actuators mounted on the same

side of the damper shaft.

OpenAir™ GCA Series Spring Return 160 lb-in Electronic Damper Actuator Technical Instructions

Document No. 155-173P25

May 19, 2014

Siemens Industry, Inc. Page 7

Accessories,

Continued

Figure 7. Tandem Mount

Bracket.

ASK73.2U: Bracket provides an extended anti-

rotation pin allowing two OpenAir modulating

actuators to directly drive a single damper shaft.

Tandem mounting bracket for two GCA16x

(standard to 10 Vdc modulating control) Series

Actuators mounted on the same side of the

damper shaft.

NOTE:For applications requiring single

damper shaft operation by up to four

GCA modulating control signal

actuators mounted on each side of

the damper shaft, use the GCA15x

Series Actuator with Master/Slave

mode operation selected.

Figure 8. Special Shaft Adapter.

ASK74.1U: Shaft adapter will attach to a

1.05-inch (26.6 mm) diameter shaft; the

standard self-centering adapter will accept up

to a one-inch (25.4 mm) diameter shaft.

•Adapter can be used for coupling to

slightly oversized one-inch (25.4 mm)

jackshafts.

•Shaft adapter is 13/16-inches (20 mm)

shorter than the height of the self-

centering shaft adapter.

Figure 9. NEMA 3R Weather

Shield.

ASK75.1U: GCA Actuators are UL listed to

meet NEMA 3R requirements (a degree of

protection against rain, sleet, snow and

damage from external ice formation) when

installed with ASK75.1U Weather Shield and

outdoor-rated conduit fittings in the vertical

position.

For dimensions, see Figure 29.

Figure 10. NEMA Type 4X

Weather Shield.

ASK75.7U: GCA Actuators are UL listed to

meet NEMA Type 4X requirements (a degree

of protection against falling dirt, rain, sleet,

snow, windblown dust, splashing water, hose-

directed water, corrosion, and damage from

external ice formation) when installed with an

ASK75.7U Weather Shield and outdoor-rated

conduit fittings. This weather shield may be

mounted in any orientation.

For dimensions, see Figure 30.

Technical Instructions OpenAir™ GCA Series Spring Return 160 lb-in Electronic Damper Actuator

Document No. 155-173P25

May 19, 2014

Page 8 Siemens Industry, Inc.

Figure 11. Heater/Weather

Shield Assembly.

985-106: Provides protection for GIB, GBB

and GCA OpenAir actuators down to

temperatures of -58°F

(-50°C). Assembly includes:

•Weather Shield

•Heater Kit

Figure 12.

499 Ohm Resistor Assembly Kit.

985-124: Used for converting a 4 to 20 mA

controller output signal into a 2 to 10 Vdc

actuator signal.

Service Parts

985-003

Position Indicators

(10/pkg.)

985-004

Standard Shaft Adapter. 985-006

Anti-rotation (Mounting)

Bracket.

985-008

Conduit Adapter,

1/2-inch (12 mm)

for 1/2-inch NPT

Connector.

Figure 13. Orderable Service Parts.

Operation

GCA12x and GCA22x: 2-Position Control

When power is applied, the actuator coupling moves toward the open position 90°.

GCA13x: Floating Control

A floating control signal controls the damper actuator. The actuator's angle of

rotation is proportional to the length of time the signal is applied. A 24 Vac/dc control

signal to Y1 causes the actuator coupling to rotate clockwise. A 24 Vac/dc control

signal to Y2 causes the actuator coupling to rotate counterclockwise.

With no control voltage, the damper actuator holds its position.

GCA16x and GCA15x: Modulating Control

A continuous 0 to 10 Vdc or 2 to 10 Vdc signal from a controller to wire Y operates

the damper actuator. The angle of rotation is proportional (or inverse proportional) to

the control signal. A 0 to 10 Vdc, or 2 to 10 Vdc position feedback output signal is

available between wires U and G0 (system neutral) to monitor the position of the

damper actuator.

OpenAir™ GCA Series Spring Return 160 lb-in Electronic Damper Actuator Technical Instructions

Document No. 155-173P25

May 19, 2014

Siemens Industry, Inc. Page 9

In the event of a power failure or when the operating voltage is shut off, all actuator

models will return to the 0 position.

In the event of a blockage in a damper, actuators are overload protected over the

full range to prevent damage to the actuators.

Life expectancy An improperly tuned loop will cause excessive repositioning that will shorten the life

of the actuator.

Control Signal

Adjustment GCA 163 and GCA164

The offset (start point) and span of the control signal can be adjusted. The offset,

Uo, can be adjusted between 0 to 5 Vdc. The span, ∆U, can be adjusted between

2 to 30 Vdc.

Ys Mechanical positioning range

(100% = angle of rotation 90°)

Yu Control signal

Uo Offset (start point)

∆U Span

Uo = 0V, ∆U = 2V

The minimum working range for Ys = 100%

1. Uo = 5V, ∆U = 30V The maximum

working range for Ys = 100%

2. Uo = 0V, ∆U ≈10V Factory setting

Setting for

10V span

0V offset

Figure 14. The Minimum and Maximum Control Signal Adjustment.

Example:

Open the actuator from 0% to 50% (45°) using a control signal of

Umin = 2V to Umax = 10V.

Calculating the value of

∆

V16

50 2)

(10x100

%inrotation

ofangleWorking min)

Umax(U%]

[

100

−

∆

Technical Instructions OpenAir™ GCA Series Spring Return 160 lb-in Electronic Damper Actuator

Document No. 155-173P25

May 19, 2014

Page 10 Siemens Industry, Inc.

Settings Uo = 2Y; ∆U = 16V

Umin = minimum control signal

Umax = maximum control signal

Figure 15. Example.

Dual Auxiliary Switch GCAxx4, GCAxx6

Actuator rotary range with the shaft

adapter mounted at position "0".

Setting range for switches A and B

Setting interval: 5°

Switching hysteresis: 2°

To change the settings of A and B:

1. Make sure the actuator is in the "0", fail-

safe position. The scale is valid only in

the "0" position.

2. Use a flat-blade screwdriver to turn the

switch adjustment dials to the desired

setting at which a signal is to be given.

Factory setting:

Switch A 5°

Switch B 85°

Figure 16. Dual Auxiliary Switch

Dials.

NOTE: For GCA15x actuators with signal inversion switch set to Inverse Acting,

90° corresponds to either a 0 to 10 Vdc or a 2 to 10 Vdc. Vdc input signal

depends on the input signal selection.

Andere Handbücher für OpenAir GCA Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens Desigo PXC5.E003 Bedienungsanleitung

Siemens

Siemens SIMATIC S7 Benutzerhandbuch

Siemens

Siemens SIRIUS 3RW44 Bedienungsanleitung

Siemens

Siemens BT300 LonWorks Benutzerhandbuch

Siemens

Siemens Albatros2 RVA78.690 Bedienungsanleitung

Siemens

Siemens RVA63.280 Bedienerhandbuch

Siemens

Siemens Simatic S7-1500 Stücklistenhandbuch

Siemens

Siemens RDU340 Series Bedienerhandbuch

Siemens

Siemens OpenAir GBB161.1U Betriebsanleitung

Siemens

Siemens MKB-1 Bedienungsanleitung

Siemens

Siemens sqm50 Bedienungsanleitung

Siemens

Siemens PXC Series Bedienungsanleitung

Siemens

Siemens RAJA+ 3TE7111-2SC18-1A Series Betriebsanleitung

Siemens

Siemens SITRANS LUT400 Bedienungsanleitung

Siemens

Siemens Synco 700 Bedienungsanleitung

Siemens

Siemens RWD68 Bedienungsanleitung

Siemens

Siemens SIRIUS S2 Bedienungsanleitung

Siemens

Siemens SIMATIC S7-400H Bedienungsanleitung

Siemens

Siemens N350E Service-Handbuch

Siemens

Siemens SIPART DR22 Bedienungsanleitung

Siemens

Siemens N 543D31 Bedienungsanleitung

Siemens

Siemens ACVATIX SKB Series Bedienungsanleitung

Siemens

Siemens Acvatix SAS31.03 Bedienungsanleitung

Siemens

Siemens RVL471 Bedienerhandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung