Siemens SINAMICS G120 Bedienungsanleitung

CU250S-2 Control Units

___________________

SINAMICS

SINAMICS G120

CU250S-2 Control Units

Compact Operating Instructions

Edition 01/2016

01/2016

A5E37058195B AA

Fundamental safety

instructions

Scope of delivery

Installing

Commissioning

More information

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E37058195B AA

Ⓟ

01/2016 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CU250S-2 Control Units

Compact Operating Instructions, 01/2016, A5E37058195B AA 3

Table of contents

1 Fundamental safety instructions.............................................................................................................. 4

1.1 General safety instructions .......................................................................................................4

1.2 Industrial security ......................................................................................................................5

2 Scope of delivery .................................................................................................................................... 6

3 Installing ................................................................................................................................................. 7

3.1 Installing the Control Unit..........................................................................................................7

3.2 Overview of the interfaces ........................................................................................................8

3.3 Terminal strips behind the upper front door............................................................................10

3.4 Operator panels ......................................................................................................................14

4 Commissioning ..................................................................................................................................... 15

4.1 Commissioning with STARTER or Startdrive .........................................................................16

4.2 Connecting the inverter to the fieldbus ...................................................................................24

4.3 Frequently required parameters .............................................................................................26

5 More information................................................................................................................................... 29

5.1 Overview of the manuals ........................................................................................................29

5.2 Technical support....................................................................................................................30

This manual describes how you install a SINAMICS G120 converter with CU250S-2 Control

Unit and commission it.

What is the meaning of the symbols in the manual?

Reference to further information in the manual

An operating instruction starts here.

This concludes the operating instruction.

Download from the Internet

DVD that can be ordered

CU250S-2 Control Units

Compact Operating Instructions, 01/2016, A5E37058195B AA 4

Fundamental safety instructions

1.1

General safety instructions

WARNING

Risk of death if the safety instructions and remaining risks are not carefully observed

If the safety instructions and residual risks are not observed in the associated hardware

documentation, accidents involving severe injuries or death can occur.

•Observe the safety instructions given in the hardware documentation.

•Consider the residual risks for the risk evaluation.

WARNING

Danger to life or malfunctions of the machine as a result of incorrect or changed

parameterization

As a result of incorrect or changed parameterization, machines can malfunction, which in

turn can lead to injuries or death.

•Protect the parameterization (parameter assignments) against unauthorized access.

•Respond to possible malfunctions by applying suitable measures (e.g. EMERGENCY

STOP or EMERGENCY OFF).

Fundamental safety instructions

1.2 Industrial security

CU250S-2 Control Units

Compact Operating Instructions, 01/2016, A5E37058195B AA 5

1.2

Industrial security

Note

Industrial security

Siemens provides products and solutions with indust

rial security functions that support the

secure operation of plants, solutions, machines, equipment and/or networks. They are

important components in a holistic industrial security concept. With this in mind, Siemens’

products and solutions undergo continu

ous development. Siemens recommends strongly

that you regularly check for product updates.

For the secure operation of Siemens products and solutions, it is necessary to take suitable

preventive action (e.g. cell protection concept) and integrate each comp

onent into a holistic,

state

-of-the-art industrial security concept. Third-party products that may be in use should

also be considered. For more information about industrial security, visit this address

(

http://www.siemens.com/industrialsecurity).

To stay informed about product updates as they occur, sign up for a product

-specific

newsletter. For more information, visit this address (

http://support.automation.siemens.com

WARNING

Danger as a result of unsafe operating states resulting from software manipulation

Software manipulation (e.g. by viruses, Trojan horses, malware, worms) can cause unsafe

operating states to develop in your installation which can result in death, severe injuries

and/or material damage.

•Keep the software up to date.

You will find relevant information and newsletters at this address

(http://support.automation.siemens.com).

•Incorporate the automation and drive components into a holistic, state-of-the-art

industrial security concept for the installation or machine.

You will find further information at this address

(http://www.siemens.com/industrialsecurity).

•Make sure that you include all installed products into the holistic industrial security

concept.

CU250S-2 Control Units

Compact Operating Instructions, 01/2016, A5E37058195B AA 6

Scope of delivery

The delivery comprises at least the following components:

●A CU250S-2 Control Unit ready for operation with installed firmware.

Options for upgrading and downgrading the firmware can be found on the Internet:

Firmware (http://support.automation.siemens.com/WW/news/en/67364620)

The fieldbus interface of the Control Unit depends on the order number.

The order number, the designation and the version of the hardware (e.g. 02)

and firmware (e.g. 4.6) can be found on the rating plate

①

of the Control Unit.

Designation

Order number

Fieldbus

CU250S-2

6SL3246-0BA22-1BA0

USS, Modbus RTU

CU250S-2 DP

6SL3246-0BA22-1PA0

PROFIBUS

CU250S-2 PN

6SL3246-0BA22-1FA0

PROFINET, EtherNet/IP

CU250S-2 CAN 6SL3246-0BA22-1CA0 CANopen

●Compact Operating Instructions in German and English

●The inverter contains open-source software (OSS). The OSS license terms are saved in

the inverter.

Reading the OSS license terms

The inverter contains open-source software (OSS). OSS comprises open source text and

satisfies special license terms. If you wish to read the license terms, you must transfer them

from the inverter to a PC.

Procedure

To transfer the OSS license terms from the inverter to a PC, proceed as follows:

1. Switch off the inverter power supply.

2. Insert an empty memory card into the card slot of the inverter.

Overview of the interfaces (Page 8)

3. Switch on the inverter power supply.

4. When you have switched on the power supply, wait 30 seconds.

During this time, the inverter writes the "Read_OSS.ZIP" file onto the memory card.

5. Switch off the inverter power supply.

6. Withdraw the memory card from the inverter.

7. Use a card reader and load the file to a PC.

You have then transferred the OSS license terms from the inverter to a PC, and you can now

read the license terms.

CU250S-2 Control Units

Compact Operating Instructions, 01/2016, A5E37058195B AA 7

Installing

3.1

Installing the Control Unit

Installing the Control Unit - General

Each Power Module has an appropriate holder for the Control Unit and a release

mechanism.

Inserting the Control Unit

Proceed as follows to plug the Control

Unit onto a Power Module:

Place the two catches of the Control

Unit in the matching grooves of the

Power Module.

Press the Control Unit onto the

Power Module until you hear that it

latches.

You have now plugged the Control Unit

onto the Power Module.

Removing the Control Unit

Remove the Control Unit from the Power Module by pressing the release mechanism.

Special features for the PM240 FSGX Power Module

To insert or detach the Control Unit, you must r

elease the two screws

at the front cover, slightly shift the front cover upwards and remove

towards the front.

Reattach the front cover before you commission the device.

Permissible Power Modules

You may operate the Control Unit with the following Power Modules:

•

PM240

•

PM240-2

•

PM250

•

PM260

•

PM340 1AC

Installing

3.2 Overview of the interfaces

CU250S-2 Control Units

8Compact Operating Instructions, 01/2016, A5E37058195B AA

3.2

Overview of the interfaces

To access the interfaces at the front of the Control

Unit, you must unplug the Operator Panel (if one is

being used) and open the front doors.

①

Terminal strips

②

Fieldbus interface

Selecting the fieldbus address:

•

PROFIBUS

•

USS

•

Modbus RTU

•

CanOpen

③

Status LED

④

USB interface for connection to a PC

⑤

No function. Keep the switch in the "Vector"

position.

⑥

Switch for analog inputs

0/4 mA … 20 mA

10/0 V … 10 V

⑦

Connection to the operator panel

⑧

Memory card slot

Installing

3.2 Overview of the interfaces

CU250S-2 Control Units

Compact Operating Instructions, 01/2016, A5E37058195B AA 9

Interfaces at the lower side of the Control Unit

Table 3- 1 Permissible encoders on the DRIVE-CLiQ interface X100

DRIVE-CLiQ

encoder

Resolver

HTL

encoder

TTL

encoder

SSI

encoder

Endat 2.1

sin/cos

encoder

Direct connection

✓

---

Connection via Sensor Module SMC10,

SMC20, SMC30, SME20 or SME25

--- ✓✓✓✓✓✓

The permissible combinations of encoders for speed control and position control are listed in

the "Basic Positioner" Function Manual:

Overview of the manuals (Page 29)

Installing

3.3 Terminal strips behind the upper front door

CU250S-2 Control Units

10 Compact Operating Instructions, 01/2016, A5E37058195B AA

3.3

Terminal strips behind the upper front door

All terminals with reference potential "GND" are connected with one another in the inverter.

Terminals 31, 32

Connection of the optional 24 V supply has the following advantages:

•The Control Unit remains in operation after disconnection of the Power Module from the line sup-

ply. The Control Unit thus maintains the fieldbus communication, for example.

•You can use terminals 51 … 54 as digital outputs.

Power supplies in conformance with SELV (Safety Extra Low Voltage) or PELV (Protective Extra Low

Voltage) are permissible.

If you use a common external power supply for terminals 31, 32 and the digital inputs, you must con-

nect GND and the reference potential of the digital input ("DI COM1/2/3") with each other.

Terminals 3, 4 and 10, 11: You may use the internal 10 V supply or an external power supply for the analog inputs. For

an internal 10 V supply: Connect AI 0, respectively AI 1- with GND.

Image 3-1 Interconnection example of the digital inputs with external 24 V power supply

Andere Handbücher für SINAMICS G120

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens Desigo RXC20.1 Bedienungsanleitung

Siemens

Siemens SQL36E series Bedienungsanleitung

Siemens

Siemens SINAMICS V20 Inverter Bedienungsanleitung

Siemens

Siemens AOP Bedienungsanleitung

Siemens

Siemens SIRIUS 3RA1.5 Bedienungsanleitung

Siemens

Siemens ST950 Bedienungsanleitung

Siemens

Siemens SSE161.05U Bedienungsanleitung

Siemens

Siemens instabus JB526C23 Bedienungsanleitung

Siemens

Siemens Ertec 400 Bedienungsanleitung

Siemens

Siemens SINUMERIK 828D Turning Bedienungsanleitung

Siemens

Siemens i-3 Bedienungsanleitung

Siemens

Siemens 7SC80 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RW30 Bedienungsanleitung

Siemens

Siemens ACVATIX SKB Series Bedienungsanleitung

Siemens

Siemens CU240E-2 Bedienungsanleitung

Siemens

Siemens N350E Service-Handbuch

Siemens

Siemens BACnet Bedienungsanleitung

Siemens

Siemens SKB32 Series Bedienungsanleitung

Siemens

Siemens DXR2.E10PL-102B Bedienungsanleitung

Siemens

Siemens SIPART PS2 6DR5 series Bedienungsanleitung

Siemens

Siemens SIMATIC EMS400S PSB-S Bedienungsanleitung

Siemens

Siemens SIRIUS 3RW44 Benutzerhandbuch

Siemens

Siemens RMU7*B series Bedienungsanleitung

Siemens

Siemens SIMATIC S5-100U Benutzerhandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung