Siemens SSE161.05U Bedienungsanleitung

Electromotoric actuator

SSE161.05U, SSF161.05U

For 2-way & 3-way 599 Series Zone Valves

●Operating voltage AC/DC 24 V, positioning signal DC 0...10 V

●Self-calibrating to the valve stroke

●Direct mounting with coupling nut, no tools required

●Manual override

●Position and actuator motion indication (LED)

●Positioning force 45 lbf (200 N)

●Parallel operation of multiple actuators possible

●3-pin terminal block

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

Siemens

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

Use

●For 2-way & 3-way 599 Series Zone Valves: 599-00210 - 599-00214, 599-00230 - 599-

00234, 599-00510 - 599-00514, 599-00530 - 599-00534

●Typically in chilled ceiling, VAV and fan coil unit applications

●Max.10 units of SSE161.05U, SSF161.05U can operate in parallel, provided the

controller output suffices.

Technical design

When the actuator is driven by DC 0…10 V positioning signal, it produces a stroke, which is

transmitted to the valve stem.

DC 0...10 V control signal

●The valve opens / closes in proportion to the

control signal at Y.

●At DC 0 V, the SSE161.05U actuator stem is

extended, and the normally open valve is fully

closed.

●At DC 0 V, the SSF161.05U actuator stem is

retracted and the normally open valve is fully open.

●When no power is supplied, the actuator maintains

its current position.

Y = Control signal Y [V]

H = Percentage of calibrated valve stroke

LED indication

Status

LED indication patterns

Variants

SSE161.05U, SSF161.05U

 Modulation: Stem retracting

Flashing green in sequence: LED1-->LED2-->LED3 (500 ms each)

Modulation: Stem extending

Flashing green in sequence: LED3-->LED2-->LED1 (500 ms each)

Stem position

At H0 (fully extended for SSE and fully retracted for SSF) - H40:

Constant green (LED3)

At H40 - H60: Constant green (LED2)

At H60 - H100 (fully retracted for SSE and fully extended for SSF):

Constant green (LED1)

Calibration

Flashing green (LED2): 100 ms on, 100 ms off

Error

Constant red (LED2)

Manual operation

Flashing green/red alternatively (LED2): Green 500 ms, red 500 ms

Siemens

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

Type summary

Type

Stock number

Operating

voltage

Running

speed

Running time

2.5 mm

Control signal

Actuator

characteristic

SSE161.05U

S55180-A157

AC/DC 24 V

5 s/mm

12.5 s ±25 %

DC 0...10 V

Linear

SSF161.05U

S55180-A158

AC/DC 24 V

5 s/mm

12.5 s ±25 %

DC 0...10 V

Linear

Ordering

When ordering, specify both type and quantity.

Example:

Type

Stock number

Designation

Quantity

SSE161.05U

S55180-A157

Electromotoric actuator

Delivery

Valves and actuators can be ordered assembled in the factory or ordered separately. For

easier valve assembly, actuators ordered separately have the actuator stem fully retracted.

Equipment combinations

Valves

Combinable valves for SSE161.05U and SSF161.05U - 2-way & 3-way 599 Series Zone

Valve

Nominal Line Size

Flow Rate

Connection

Inch

Kvs

NPT

Sweat

2-Way

0.5

1.0

(0.85)

599-00210

599-00510

0.5

2.5

(2.15)

599-00211

599-00511

0.5

4.0

(3.4)

599-00214

599-00514

0.75

4.1

(3.5)

599-00212

599-00512

7.0

(6.0)

599-00213

599-00513

3-Way

0.5

1.0

(0.85)

599-00230

599-00530

0.5

2.5

(2.15)

599-00231

599-00531

0.5

4.0

(3.4)

599-00234

599-00534

0.75

4.1

(3.5)

599-00232

599-00532

7.0

(6.0)

599-00233

599-00533

Siemens

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

Note: To ensure trouble-free operation of

third-party valves with the SSE/SSF..

actuators, the valves must satisfy the

following requirements:

●Threaded connections with coupling nut

M30 ×1.5.

●Nominal force F ≤ 45 lbf (200 N)

●Dimension X ≥ 0.33 in (8.3 mm)

●Dimension Y ≤ 0.58 in (14.8 mm)

Product documentation

Topic

Title

Document ID

Installation

Mounting instruction

A6V13122037

Standards and directives

CE declarations

A5W00254962A

RCM conformity

A5W00254983A

Environmental compatibility

Environmental declarations

A5W00242127A

Related documents such as the environmental declarations, declarations of conformity, etc.,

can be downloaded from the following Internet address:

www.siemens.com/bt/download

Notes

Engineering

The actuators must be electrically connected in accordance with local regulations (see

"Connection diagrams”).

CAUTION

National safety regulations

Failure to comply with national safety regulations may result in personal injury and property

damage.

●Observe national provisions and comply with the appropriate safety regulations.

Observe permissible temperatures (see "Technical data [▶8]").

Mounting

WARNING

●Do not use pipe wrenches, pliers or similar tools.

●Avoid lateral pressure or (cable) tension on the mounted actuator!

Valve and actuator are easy to assemble on site before commissioning:

●Remove protective cover from the valve body.

●Position the actuator and tighten the union nut manually.

●See "Mounting instruction" for graphical instructions.

Siemens

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

Orientation

Commissioning

When commissioning, check both wiring and functioning of the actuator.

●Actuator stem extends

Normally open valve closes, normally closed

valve opens

●Actuator stem retracts

Normally open valve opens, normally closed

valve closes

NOTICE

The actuator must be commissioned only with a correctly mounted valve in place!

Self-calibration

When operating voltage is applied, the actuator self-calibrates (fully retracted ➙fully

extended ➙setpoint).

CAUTION

Never intervene manually during self-calibration.

NOTICE

●Correct calibration is only possible with valve stroke > 0.05 inch (1.2 mm). Valve stroke

< 1.2 mm results in calibration failure.

●If calibration fails, the actuator performs another calibration automatically after

10 seconds.

●After three failed calibration attempts, the actuator stem remains in the extended

position and the valves are open.

Manual operation

A 3-mm hexagonal wrench can be used to move the actuator to any position.

Power

Calibration Y

Fully retracted

Fully extended

Siemens

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

To move the actuator stem manually

1. Open the cover using a proper screwdriver.

2. Press and hold down button (a) illustrated below for at least three seconds.

–The actuator ignores any control signal from the controller.

3. Adjust the position of the actuator stem by rotating hexagonal wrench (b) illustrated

below clockwise or counter-clockwise.

–The actuator stem moves down if you rotate clockwise; it moves up if you rotate

counter-clockwise. The manually set position is retained.

4. To exit manual operation mode, press and hold down button (a) illustrated below again

for at least three seconds.

–The actuator runs a self-calibration automatically. Control signal sent from the

controller takes effect.

5. Close the cover.

NOTICE

If operating voltage is applied to actuator, press button (a) before and after manually

adjusting the position of the actuator stem. If no operating voltage and control signal are

applied, manual operation can be done without pressing button (a).

Cabling operation

1. Unscrew cover screw

2. Remove cover

3. Connect or disconnect wire terminals (terminal block is removable)

4. Install the cover

5. Screw in the cover screw

A6V11858278Z10

3 mm

(b)

(a)

> 3s

Siemens

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

Maintenance

The actuators require no maintenance.

WARNING

Operating voltage must be switched off during any maintenance!

NOTICE

When carrying out service work on the plant, note the following:

●Switch off operating voltage.

●If necessary, disconnect electrical connections from the terminals.

●The actuator must be commissioned only with a correctly mounted valve in place!

Repair

The actuators cannot be repaired; the complete unit must be replaced.

Disposal

The device is considered an electronic

device for disposal and may not be disposed

of as domestic waste.

●Dispose of the device through channels

provided for this purpose.

●Comply with all local and currently

applicable laws and regulations.

Warranty

Technical data on specific applications are valid only together with Siemens products listed

under "Equipment combinations". Siemens rejects any and all warranties in the event that

third-party products are used.

Open Source Software (OSS)

Software license overview

These devices use Open Source Software (OSS). All Open Source Software components

used in the product (to include copyrights and licensing agreement) are available at

http://siemens.com/bt/download.

Firmware version

OSS document

Device

Document ID

Title

2.10.0 or above

A6V13503690

Readme OSS for Modulating Room Actuator 200 N, 300 N

All

Siemens

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

Technical data

Power supply

Operating voltage

AC 24 V (±15 %) or DC 24 V (±20 %)

Frequency

50/60 Hz

Power consumption

3 VA (AC); 1.2 W (DC)

Primary fuse or breaker rating

External, 2 A quick blow

Signal input

Control signal

DC 0…10 V

Input impedance

100 kOhm

Parallel operation (number of actuators)

Max. 101)

1) Provided that the controller output is sufficient.

Operating data

Position with de-energized contact Y

See "Technical design [▶2]"

Running speed (time for 2.5 mm)

< 5 s/mm ±25 % (12.5 s ± 25 %)

Positioning force

45 lbf (200 N)

Stroke

0.05 to 0.25 inch (1.2…6.5 mm)

Permissible temperature of medium in the connected

valve

34 to 248°F (1…120℃)

Electrical connection

Permissible length for signal lines

65 ft (20 m)

Wire cross section

18...20 AWG (0.5...0.75 mm²）

Cable diameter

<0.2 inch （5 mm）

Mounting

Connection to valve

Plastic coupling nut M30 × 1.5

Orientation

Above horizontal

Standards

EU conformity declaration (CE)

A5W00254962A

RCM conformity declaration

A5W00254983A

UK conformity declaration (UKCA)

A5W00257055A

Housing protection degree

NEMA 2 / IP20 (EN 60529)

Protection class according to EN 60730

III

Siemens

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

Standards

Pollution degree

Overvoltage category

Environmental compatibility

The product environmental declaration

(A5W00242127A) contains data on environmentally

compatible product design and assessments (RoHS

compliance, materials composition, packaging,

environmental benefit, disposal).

UL Approval

Federal Communications Commission

UL as per UL60730-1, UL60730-2-14

http://ul.com/database

cUL as per CSA –CAN E60730-1, E730-2-14

FCC CFR 47 Part 15 Class B

ICES003

CAN ICES-3 (B)/NMB-3(B)

FCC regulations

Modification of this device to receive cellular radio telephone service signals is pro-

hibited under FCC rules and federal law.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Housing color

Cover/base

2003, Ti-Gray

Coupling nut

RAL 9017

General ambient conditions

Operation

Transport

Storage

Temperature

34 to 122°F (1…50 ℃)

-13 to 158°F (-25…70 ℃)

Humidity

5…95 % r.h.

non condensing

< 95 % r.h.

non condensing

5…95 % r.h.

non condensing

Atmospheric

pressure

Min. 700 hPa, corresponding to

max. 3,000 m above sea level

Siemens

A6V12681514_enUS_b

Smart Infrastructure

06/15/2023

Material

Cover/base

PC + ABS

Weight

SSE161.05U

7.7 ounces (217 g)

SSF161.05U

7.6 ounces (216 g)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens SIRIUS 3RA2110 Series Bedienungsanleitung

Siemens

Siemens SIRIUS Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Stücklistenhandbuch

Siemens

Siemens IP Control Center N152 Bedienungsanleitung

Siemens

Siemens OpenAir GDE Series Betriebsanleitung

Siemens

Siemens RWD68 Bedienungsanleitung

Siemens

Siemens Flowrite 599 Series Betriebsanleitung

Siemens

Siemens IQHeat Bedienungsanleitung

Siemens

Siemens ERTEC200 Bedienungsanleitung

Siemens

Siemens Synco700 RMK770 Bedienerhandbuch

Siemens

Siemens OpenAir GQD Series Bedienungsanleitung

Siemens

Siemens SIRIUS 3RA142 8XC21 Sries Bedienungsanleitung

Siemens

Siemens BACnet ATEC Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Stücklistenhandbuch

Siemens

Siemens Simatic S7-1500/ET 200MP Benutzerhandbuch

Siemens

Siemens ATC5300 Bedienungsanleitung

Siemens

Siemens RVP550 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Benutzerhandbuch

Siemens

Siemens SIMOTION P350-3 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens RBC Bedienungsanleitung

Siemens

Siemens Gamma instabus UP204 Contouch Service-Handbuch

Siemens

Siemens SINUMERIK 808D Bedienungsanleitung

Siemens

Siemens OpenAir GLB Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung