Siemens FDCW241 Leitfaden
FDCW241
Radio gateway
Mounting
A6V10227641_h_en_-- Smart Infrastructure
2020-03-31
Imprint
Technical specifications and availability subject to change without notice.
Transmittal, reproduction, dissemination and/or editing of this document as well as
utilization of its contents and communication thereof to others without express
authorization are prohibited. Offenders will be held liable for payment of damages.
All rights created by patent grant or registration of a utility model or design patent
are reserved.
Issued by:
Siemens Switzerland Ltd.
Smart Infrastructure
Global Headquarters
Theilerstrasse 1a
CH-6300 Zug
Tel. +41 58 724-2424
www.siemens.com/buildingtechnologies
Edition: 2020-03-31
Document ID: A6V10227641_h_en_--
© Siemens Switzerland Ltd, 2012
Imprint
2 | 20 A6V10227641_h_en_--
A6V10227641_h_en_-- 3 | 20
Table of contents
1 About this document................................................................................. 5
2 Mounting/Installation............................................................................... 6
2.1 Mounting................................................................................................... 6
2.2 Mounting in housing FDCH221 ................................................................ 8
2.3 Connecting the radio gateway .................................................................. 9
3 Details for ordering ................................................................................... 12
3.1 Radio gateway FDCW221 ........................................................................ 12
3.2 Connection terminal DBZ1190-AB ........................................................... 12
3.3 Battery pack BAT3.6-10 ........................................................................... 12
3.4 Housing FDCH221 ................................................................................... 13
3.5 Housing base FDCH271........................................................................... 13
3.6 Housing cover FDCH272.......................................................................... 13
3.7 MCL-USB (radio) adapter FDUZ227 ........................................................ 14
4 Specifications ........................................................................................... 15
4.1 Technical data .......................................................................................... 15
4.2 Dimensions............................................................................................... 18
4.3 Master gauge for recesses ....................................................................... 18
4.4 Environmental compatibility and disposal................................................. 19
4 | 20 A6V10227641_h_en_--
1 About this document
Goal and purpose
This document contains information required to mount the radio gateway
FDCW241.
Prerequisites:
● The installation location of the radio gateway has been established.
● Mounting should be performed by a specialist in compliance with safety
regulations.
You will find more information on the radio gatewayFDCW241 in document
A6V10227639.
Intended use
The radio gateway FDCW241 must only be used on a FDnet/C-NET detector line
in a fire detection system FS20/FS720.
● Specialist electrical engineering knowledge is required for installation.
● Only an expert is permitted to carry out installation work.
Incorrect installation can take safety devices out of operation unbeknown to a
layperson.
Applicable documents
Document ID Title
A6V10227631 Planning Radio fire detection system SWING
A6V10227639 Technical manual Radio gateway FDCW241
A6V10271323 Data sheet SWING Neural radio fire detector FDCW241,
FDOOT271, FDM273, FDM275, FDM275(F)
About this document 1
A6V10227641_h_en_-- 5 | 20
2 Mounting/Installation
2.1 Mounting
AB
C
2
1
3
4
5
5
Figure 1: Installing the radio gateway
1 Housing cover
2 Screw
3 Lock
4 Strain relief fastenings
5 Cable entries
wYou have the radio gateway, battery pack, fixing screws, and cable tie to hand.
wYou have the device location plan to hand.
wThe connection cable has a conductor cross-section of 0.2…1.5mm².
wThe lines to the installation location are installed.
wTwo fixing screws (Ømax.4.3mm) are to hand.
1. Determine the installation location:
– The housing must be positioned in accordance with the planning
specifications (make sure there is a wide radio range and that the housing
can be accessed easily).
– Make sure there is enough space for you to open the housing cover easily.
– The housing may be installed in any appropriate position.
2. Open the housing:
– Remove the screw(2)(A).
– Using a screwdriver to press the lock(3) into the housing(B) and unlock
the housing cover(1).
– Lift the housing cover(1) and remove it.
3. Remove the adhesive label bearing the serial number from the back box and
use it to mark the installation location on the device location plan.
4. In the back box, break out the plastic for the cable entry (5):
– Openings in the supporting surface for recess-mounted cables
– Openings in the narrow side for surface-mounted cables
5. Insert the cables into the back box.
6. Mount the back box, without the battery pack, on a flat surface using two
screws (Ømax.4.3mm) at the mounting points (see
'Master gauge for recesses [➙18]' chapter). One screw at the mounting point
is sufficient for fixing in housing FDCH221.
Mounting/Installation
Mounting
2
6 | 20 A6V10227641_h_en_--
7. Fasten the cable using a cable tie as strain relief (4).
8. Label the battery pack with the date.
9. Insert the battery pack and check the position of the battery cable. Do not
connect the battery pack until you are ready to commission the radio cell.
aThe radio gateway is installed.
Mounting/Installation
Mounting 2
A6V10227641_h_en_-- 7 | 20
2.2 Mounting in housing FDCH221
The radio gateway can be installed in a separate housing FDCH221. The housing
protects the radio gateway from dirt and dust.
Ø max. 4.8 mm
1 2 3 4 5
Figure 2: Installing housing FDCH221
1 Cable entry 4 Screws for securing the housing
2 Cables 5 Screws for housing cover
3 Screw for radio gateway
Proceed as follows to install the radio gateway in housing FDCH221:
1. Break out the required cable entries(1) on the housing.
2. Install the housing with screws(4) on a level surface.
3. Insert the cables(2). If necessary, fix the cables using M20x1.5 cable glands
or use a different cable entry.
4. Remove the housing cover from the radio gateway and dispose of it in an
environmentally-friendly manner.
5. Install the radio gateway in the housing using the fixing screw(3) provided.
6. Connect the radio gateway.
7. Close the housing using the screws(5) provided.
aThe radio gateway is now installed in housingFDCH221. The radio gateway
indicators can be viewed through the window of the housing.
Mounting/Installation
Mounting in housing FDCH221
2
8 | 20 A6V10227641_h_en_--
2.3 Connecting the radio gateway
● Specialist electrical engineering knowledge is required for installation.
● Only an expert is permitted to carry out installation work.
Incorrect installation can take safety devices out of operation unbeknown to a
layperson.
Once all the radio devices of a radio cell have been logged on to the radio
gateway(B) in battery mode (A), the radio gateway can be connected to the FDnet/
C-NET detector line(C).
AFC20xx
FC72x
SWING
FDCW241
BFC20xx
FC72x
SWING
FDCW241
CFC20xx
FC72x
SWING
FDCW241
Figure 3: Connecting the radio cell to the detector line
++ __
+_
++ __
+-+-
+-
1111
Figure 4: Connections on radio gateway FDCW241
1 detector line terminal strip
The radio gateway 'FDCW241' automatically assigns the additional, virtual address
'FDCL221v' as a line separator. When you assign the connections, you determine
the order in which the devices are read in at the control panel.
Mounting/Installation
Connecting the radio gateway 2
A6V10227641_h_en_-- 9 | 20
The following topologies are possible:
Radio cell as LOOP
1
2
X1
LOOP1_2+
LOOP1_2-
3
4
LOOP1_1+
LOOP1_1-
-
+
-
+
FC20xx
FC720x
1
2
X1
LOOP1_2+
LOOP1_2-
3
4
LOOP1_1+
LOOP1_1-
-
+
-
+
++ __
+_
+-+-
+-
++ __
+_
+-+-
+-
FC20xx
FC720x
Figure 5: Loop connection
Radio cell as stub
Figure 6: Stub connection only
Mounting/Installation
Connecting the radio gateway
2
10 | 20 A6V10227641_h_en_--
Andere Handbücher für FDCW241
2
Inhaltsverzeichnis
Andere Siemens Tor Handbücher
Siemens
Siemens 5WG1 141-1AB31 Service-Handbuch
Siemens
Siemens SIMATIC RTLS Series Bedienungsanleitung
Siemens
Siemens SIMATIC NET S7-CPs Bedienungsanleitung
Siemens
Siemens VNT Bedienungsanleitung
Siemens
Siemens SIRIUS 3RK3141 Series Bedienungsanleitung
Siemens
Siemens RUGGEDCOM WIN5151 Bedienungsanleitung
Siemens
Siemens FDCW221 Bedienungsanleitung
Siemens
Siemens Gigaset SX686 WiMAX Bedienungsanleitung
Siemens
Siemens VersiComm VC1COMMA Bedienungsanleitung
Siemens
Siemens SIMATIC PN/J1939 LINK Bedienungsanleitung
Siemens
Siemens 5WG1143-1AB01 Bedienungsanleitung
Siemens
Siemens SIMATIC RTLS Series Anwendungshandbuch
Siemens
Siemens SIMATIC NET IE/WSN-PA Link Administratorhandbuch
Siemens
Siemens ProtoAir FPA-W44 Benutzerhandbuch
Siemens
Siemens NK8237 MP4.40 Stücklistenhandbuch
Siemens
Siemens A53457 Wartungs- und Serviceanleitung
Siemens
Siemens OCT200.KNBA Bedienungsanleitung
Siemens
Siemens FDCW241 Bedienungsanleitung
Siemens
Siemens SIMATIC IOT Gateway MQTT Benutzerhandbuch
Siemens
Siemens RUGGEDCOM WIN5137-V Bedienungsanleitung
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
