Siemens LITHOSTAR Multiline Einrichtungshandbuch

LITHOSTAR Multiline

Print No.: RXL2-120.091.08.04.02 Doc. Gen. Date: 10.00

Replaces: RXL2-120.091.08.03.02

The reproduction, transmission or

use of this document or its contents

is not permitted without express

written authority. Offenders will be

liable for damages. All rights,

including rights created by patent

grant or registration of a utility

model _or_design,_are_reserved.

System Manual

Replacement of Operating PC

Repair Instructions

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 2 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

0 - 2 Revision

Chapter Page Revision

0all04

1all04

2all04

3all04

4all04

5all04

Contents 0 - 3

Siemens AG Register 5 RXL2-120.091.08 Page 3 of 4 LITHOSTAR Multiline

Medical Engineering Rev. 04 10.00 TD PS 24 System Manual

1 _______Software generation ____________________________________________1 - 1

Rear view of the operating PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

2 _______Operating PC SCENIC Pro C5/ Pro C6______________________________2 - 1

Mechanical changes in the control console . . . . . . . . . . . . . . . . . . . . . . .2 - 1

Opening the operating PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2

Installing board D51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 - 3

Closing the operating PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 4

3 _______Operating PC LM Control Unit ____________________________________3 - 1

Open operating PC and install board D51. . . . . . . . . . . . . . . . . . . . . . . . 3 - 3

Close the operating PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 - 3

4 _______Changes to previous version_____________________________________4 - 1

Page

0 - 4 Contents

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 4 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

This page intentionally left blank.

Page

1 - 1

Siemens AG Register 5 RXL2-120.091.08 Page 1 of 4 LITHOSTAR Multiline

Medical Engineering Rev. 04 10.00 TD PS 24 System Manual

Rear view of the operating PC 1

1 Keyboard port 5 Parallel interface X50 Respirator-ECG signal interface

2 Moouse port 6 Monitor port X51 DUEP port

3 Serial interface COM 1 7 Power line connector

4 Monitor power line connector

SCENIC Pro C6

Position D51

X50 X51

2356

4Position D51

LM - Control Unit

X50 X51

SCENIC Pro C5 7

X51

X50

Software generation 1

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 2 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

1 - 2 Software generation

•SwitchthesystemOFF.

•Placethenew operatingPCinthedrawerof thesystemcontrolconsole.

•Connectthe followingcablestotheoperatingPC:

- linevoltagecableforoperatingPC

- linevoltagecableformonitor

- signalcableformonitor

- signalcableformouse

- signalcableforkeyboard

•SwitchthesystemON.

The greenLED onthe operatingPC mustlightup.

•On the operatingPC.

•SwitchthesystemOFF.

•InsertthebootdiskindriveA of theoperatingPC.

•SwitchthesystemON.

•Ifthekeyboardisreplaced,theUserTerminalsoftwaremustbe reinstalled.

Answeraccordingly.

SCENIC Pro C5 / C6

Ïthe following message appears:

"MS-DOS 6.2 Startup Menü"

•usethedown arrowkey"↓" to select

"2.PCneu startenodermanuell

ausschalten"

German texts will appear during the installation of the software

→This is due to the German operating system.

NOTICE

User-Terminal-Software Installation?

No: Press [ Ctrl ]+ [ C ]

YES: Press any key, to continue

Eine beliebige Taste drücken, um fortzusetzen.

Software generation 1 - 3

Siemens AG Register 5 RXL2-120.091.08 Page 3 of 4 LITHOSTAR Multiline

Medical Engineering Rev. 04 10.00 TD PS 24 System Manual

•Afterafew moments,thefollowingcommandappears:

•Pressthe"J" key and then"Enter/Entrée".

•Thecommand to enterthe type of keyboardappears:

•Selecteither"E"or"F",dependingon the type ofkeyboard,andpress"ENTER"/Entrée".

•Afterafew moments,thefollowingcommandappears:

•Removethe boot disk from driveA.

•Insertthebackupdisk01 in drive A.

•Pressanykey.

•When the system finishesloadingbackupdisk01,the followingcommand appears:

•Remove backup disk 01from drive A.

•Insertbackupdisk02 in driveA.

•Repeatthesame procedurefortheremainingbackupdisks.

•Onceallthe backup diskshavebeen loaded,the followingmessageappears:

•Remove backup disk 05from drive A.

•InserttheUserInterfaceSWdisk in drive A.

Hard-Disk will be formatted!

Please wait 5 sec. for next message and press "J" and [ENTER ] !

WARNUNG! Alle Daten auf der Festplatte in Laufwerk C:

werden gelöscht!

Formatieren durchführen (J/N)?

Enter keyboard type:

E: englisch (international) keyboard

F: french keyboard

Press "E" or "F" according to keyboard type and press [ENTER ]:

Please insert "Backup-Disk 01... 05" (Sicherungdiskette 01... 05)!

Press any key, to continue!

Sicherungsdiskette 01 in Laufwerk A: einlegen

Eine beliebige Taste drücken, um fortzusetzen

Sicherungsdiskette 02 in Laufwerk A: einlegen

Eine beliebige Taste drücken, um fortzusetzen

Please insert disk: "User-Interface-SW"!

Press any key, to continue!

Eine beliebige Taste drücken, um fortzusetzen

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 4 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

1 - 4 Software generation

•Afterafew moments,thefollowingcommandappears:

•Remove the User Interface SW disk from drive A.

•InserttheStatusdiskindriveA.

•Afterafew moments,thefollowingcommandappears:

•Removethe Status disk from drive A.

•InsertthebootdiskindriveA.

•Afterafew moments,thefollowingcommandappears:

•SwitchthesystemOFF.

•Removethe boot disk fromdriveA.

•Fortheadditionalstepsrequired,refertothechapterwhichcorrespondsto theoperating

PC being used.

Do not activate the write protection on the diskette, since data

must be written onto it.

Please insert "Status-Disk"!

Press any key, to continue!

Eine beliebige Taste drücken, um fortzusetzen

CAUTION

Please insert "BOOT-Disk" again!

Press any key, to continue!

Eine beliebige Taste drücken, um fortzusetzen

*******A T T E N T I O N: I M P O R T A N T N O T E! *********

Modify CMOS-SETUP according to service-manual!

- CMOS-Setup-Lock by Password

- Disable Disk-Controller

See instructions!

Please remove disk!

Now, switch off the PC and turn it on again for CMOS-Setup-Modify!

Thank you!

2 - 1

Siemens AG Register 5 RXL2-120.091.08 Page 1 of 4 LITHOSTAR Multiline

Medical Engineering Rev. 04 10.00 TD PS 24 System Manual

Mechanical changes in the control console 2

•Especially in thecase oftheSCENIC ProC5: operating PC

- Replacetheexistingground conductorin the controlconsolebythelongerone from

theconversionkit4783 416.

- Connectthecablefor the DUEP connectionX51and fastenfirmlyon thetopof the

connectorbracketusingtheclipfrom the conversion kit.

- Placethewoodenconsolefrom the conversionkit4783 416 onthe drawer.

- PlacetheoperatingPCon thewooden console.

•When the message "PressF2to enterSETUP" appears,pressthe"F2"key.

TheCMOS setupmenu appears.

•Selectthe"Main"menu usingthe← →cursorkeys.

•Inthe "Main" menu, use the ↑ ↓ cursorkeystoselectthe submenu "Boot Option".

•Pressthe "ENTER"key; use "Entrée"onthe French keyboard.

•Setthe"Post Errors"menu to "No Halt on Any Errors"usingthe +/- keys

(numerickeypad).

•Selectthe"FastBoot"menu using the↑ ↓cursorkeys.

•Setthe"Fast Boot" menu to"Enabled"usingthe +/- keys (numeric keypad).

•Selectthe"QuietBoot"menu usingthe↑ ↓cursor keys.

•Setthe"Quiet Boot" menu to"Enabled"usingthe+/-keys(numerickeypad).

•Selectthe"BootSequence:1."menu using the ↑ ↓cursorkeys.

•Setthe"Boot Sequence: 1." menu tothe harddiskusingthe "-" key (numeric keypad.

(theharddiskis1; the disketteis2).

•Pressthe "Esc" key; use the "Echap"keyon the Frenchkeyboard.

•Selectthe"Advanced"menu using the ← → cursorkeys.

•Inthe"Advanced"menu, use the↑ ↓ cursorkeys toselectthesubmenu"Peripheral

Configuration".

•Pressthe "ENTER"key; use "Entrée"onthe French keyboard.

•Selectthe"DisketteController" menu using the ↑ ↓cursorkeys.

•Setthe"DisketteController"menuto"Disabled"usingthe+/-keys(numerickeypad)

•Pressthe"Esc" key; use "Echap" on theFrenchkeyboard.

•Selectthe"Security"menuusingthe← → cursor keys.

•Inthe"Security"menu, use the ↑ ↓ cursorkeystoselect"SetSetup Password".

•Pressthe "ENTER"key; use "Entrée"onthe French keyboard.

•Enterthepassword"TDRX".

•Pressthe "ENTER" key twice;use"Entrée"onthe French keyboard.

•Enterthe password"TDRX" again.

Operating PC SCENIC Pro C5/ Pro C6 2

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 2 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

2 - 2 Operating PC SCENIC Pro C5/ Pro C6

•Pressthe"ENTER" key; use "Entrée"on the French keyboard.

•Usethe↑ ↓ cursor keys to selectthesubmenu "FlashWrite".

•Setthe"Flash Write"menu to"Disabled"usingthe+/-keys(numerickeypad).

•Pressthe"Esc"key;use "Echap" on theFrenchkeyboard.

•Usethe← → cursorkeystoselectthe"Power"menu.

•Usethe↑ ↓ cursor keys to select the"APM"menu.

•Setthe"APM" menuto "Disabled"usingthe +/- keys (numerickeypad).

•If"PowerManagementMode" is notsetto "Disabled",usethe↑ ↓cursorkeys to select

"PowerManagementMode".

•Pressthe"Esc"key;use "Echap" on theFrenchkeyboard.

•Selectthe"Power"menu using the ← → cursorkeys.

•Inthe "Power" menu, use the↑ ↓ cursorkeys toselectthesubmenu"PowerManage-

mentMode".

•Setthe"Power Management Mode"menu to "Disabled" usingthe +/- keys (numeric

keypad).

•Pressthe"Esc"key;use "Echap" on theFrenchkeyboard.

•Pressthe"ENTER" key twice;use"Entrée"onthe French keyboard.

•Afteramoment, the Multiline operatingsoftwarewilldisplaythe start-upmessage:

"NoHost Communication".

•SwitchthesystemOFF.

Opening the operating PC 2

•Removeallexternalcables.

•Openthe operatingPC (1/Fig.1).

•Slidethedrivecovertothe left (2/Fig.1).

•Forthe upper part of the housing

- slightly lifttherearedge (1/Fig.2).

- slidetowardsthefront(2/Fig.2).

- liftitupwards(3/Fig. 2).

Fig. 1 Fig. 2

Andere Handbücher für LITHOSTAR Multiline

Inhaltsverzeichnis

Andere Siemens Industrieanlagen Handbücher

Siemens

Siemens SCALANCE XR124WG Bedienungsanleitung

Siemens

Siemens SIRIUS 8WD4428-0BC Bedienungsanleitung

Siemens

Siemens S5-135U Benutzerhandbuch

Siemens

Siemens D2300CPS Bedienungsanleitung

Siemens

Siemens SITRANS LPS200 Bedienungsanleitung

Siemens

Siemens SIWAREX WL290 DB-S CA Bedienungsanleitung

Siemens

Siemens RHVE64X Bedienungsanleitung

Siemens

Siemens 3VA1 Series Bedienungsanleitung

Siemens

Siemens SENTRON VL Bedienungsanleitung

Siemens

Siemens Simatic ET 200pro FC Bedienungsanleitung

Siemens

Siemens MOTOX BA 2510 Bedienungsanleitung

Siemens

Siemens LITHOSTAR Multiline Bedienungsanleitung

Siemens

Siemens 3VT9300-1SB00 Bedienungsanleitung

Siemens

Siemens SIMATIC MV320 Bedienungsanleitung

Siemens

Siemens SITRANS L Administratorhandbuch

Siemens

Siemens SIMATIC S7-1500R/H Technisches Dokument

Siemens

Siemens 7KM9900 - 0GA00 - 0AA0 Bedienungsanleitung

Siemens

Siemens SINUMERIK ONE NCU 1740 Technisches Dokument

Siemens

Siemens 3KL84 Series Bedienungsanleitung

Siemens

Siemens 3TX7002 Bedienungsanleitung

Siemens

Siemens LI L Series Bedienungsanleitung

Siemens

Siemens 3VA9677-0CB10 Bedienungsanleitung

Siemens

Siemens LDS 6 Bedienungsanleitung

Siemens

Siemens DM1103-L Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Rioned

Rioned UrbanJet Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung