Siemens Operator Display Panel II Bedienungsanleitung

Installation Instructions

Document No. 570-111

February 18, 2013

Operator Display Panel II (ODP II)

Item No. 570-111. Rev. AA Page 1 of 4

Product Description

These instructions explain how to field install or

replace the BACnet Fume Hood Controller FHC.

The Fume Hood Controller Operator Display Panel

(ODP) is the interface between the fume hood

operator and the controller system. The mounting

plate is designed for the fume hoods with or without

existing cutouts.

Designed for wall-mounting (A). A conduit box

is optional.

Base plate (B) has screw holes for all

commercially available conduit boxes. The

height of the screw heads must not exceed 3

mm.

Device (C) incorporates a plug, an LCD panel,

emergency purge and horn silence buttons.

Product Number

575-820A

Required Tools

For fume hood with an existing cutout, you need:

Medium Phillips-head screwdriver

For fume hood without a cutout, you need:

Medium duty electric drill

1-1/2 inch (38 mm) hole saw bit

Prerequisites

Cable from controller to ODP is in place.

Cable from controller to ODP is less then 50 feet

(15 m) in length.

Document No. 570-11

Installation Instructions

February 18, 2013

Page 2 of 4 Siemens Industry, Inc.

Installation Instructions

NOTE:

The ODP must be mounted so that the

fume hood operator can easily read its

display and reach its buttons.

1. Choose the mounting location for the ODP. The

panel can be mounted directly on the fume

hood over a pre-existing cutout, on a nearby

wall or over a conduit box.

2. Continue with one of the following:

- Installing a Cutout

- Installing the ODP

Installing a Cutout

1. Using the mounting plate as a template, mark

the location for the mounting holes and

interface cable/connector.

2. Drill the two mounting holes using a 3/16-inch

(5 mm) bit.

3. Cut the controller interface port clearance hole

using a 1-1/2 inch (38 mm) hole saw.

Installing the ODP

1. Position the mounting bracket over the existing

cutout on the fume hood. Align the holes on the

mounting bracket with the screw holes of the

cutout.

NOTE: Make sure that there is enough

clearance for the controller interface port on the

ODP.

2. Attach the mounting plate to the mounting

surface using the screws provided.

NOTE: The height of the screw heads must not

exceed 3 mm.

3. Pull the cable through the plate and connect it

to the ODP at the controller interface port.

4. Place the ODP onto the mounting bracket so

that the flange engages into the slots located

inside the top of the panel housing.

5. Push until locking tab clicks in place.

Document No. 570-111

Installation Instructions

February 18, 2013

Siemens Industry, Inc. Page 3 of 4

6. Connect the power module to the ODP and

Fume Hood Controller.

The installation is complete.

Dismounting the ODP

1. Push the locking tab with a screwdriver until it

releases.

2. Remove the display fro the mounting plate.

Mounting plate dimensions.

Document No. 570-11

Installation Instructions

February 18, 2013

Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as

design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners.

Siemens Industry, Inc.

Building Technologies Division

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

USA

Your feedback is important to us. If you have

comments about this document, please send them

to SBT_technical.editor.us.sbt@siemens.com.

Document No.570-111

Printed in the USA

Page 4 of 4

ODP Driver Installation

Obtain the driver files from one of the following

locations and copy the folder locally to your hard

drive:

- Technical Support Web site, choose the

Critical Environment patches link.

- Standard Apps

A Micro-B USB cable is required for communication.

The suggested length of Micro-USB cable should be

6 foot in length. Below is a picture representation of

the Micro-B USB cable. Note that the Micro-A USB

cable style will not work.

Inhaltsverzeichnis

Andere Siemens Industriemonitor Handbücher

Siemens

Siemens INOX PRO SIMATIC IFP1900 Bedienungsanleitung

Siemens

Siemens SIMATIC IPC477E Bedienungsanleitung

Siemens

Siemens SIMATIC Industrial Flat Panel IFP1500 Bedienungsanleitung

Siemens

Siemens SIMATIC Industrial Flat Panel IFP2200 Bedienungsanleitung

Siemens

Siemens SIMATIC Industrial Flat Panel IFP2200 Bedienungsanleitung

Siemens

Siemens SIMATIC Industrial Flat Panel IFP1500 Bedienungsanleitung

Siemens

Siemens INOX PRO SIMATIC IFP1900 Administratorhandbuch

Siemens

Siemens Simatic MP 377 Bedienungsanleitung

Siemens

Siemens RD150 Bedienungsanleitung

Siemens

Siemens MTP700 Unified Comfort Bedienungsanleitung

Siemens

Siemens SIMATIC Industrial Flat Panel IFP2200 Bedienungsanleitung

Beliebte Industriemonitor Handbücher anderer Marken

JUMO

JUMO mTRON T Bedienungsanleitung

SWEDX

SWEDX SWSS156 Bedienungsanleitung

Saia

Saia PCD7.D410VTCF Bedienungsanleitung

weintek

weintek EasyView MT-608S Bedienungsanleitung

Advantech

Advantech FPM-212 Series Bedienungsanleitung

Advantech

Advantech FPM-3191G Series Bedienungsanleitung

Austin Hughes

Austin Hughes RP-F821 Bedienungsanleitung

WAGO

WAGO WAGO-PERSPECTO 762 Series Produkthandbuch

HIS

HIS HIS-ML12-Series D Bedienungsanleitung

Advantech

Advantech IDS-3319 Series Bedienungsanleitung

Acnodes

Acnodes APH 8064 Bedienungsanleitung

Acnodes

Acnodes APW 5400 Bedienungsanleitung

Dynamic Displays

Dynamic Displays QES1500 Progressive Series Bedienungsanleitung

AXIOMTEK

AXIOMTEK Dk3g4PANEL 6153-O/P Bedienungsanleitung

ESA

ESA XM7W7 Bedienungsanleitung

Advantech

Advantech IDK-1115WP-45FHA1 Bedienungsanleitung

Eaton

Eaton XV-152 Series Bedienungsanleitung

bon

bon BSM-153H Bedienungsanleitung