Siemens SIMATIC IPC277D/E 19" INOX PRO Bedienungsanleitung

___________________

SIMATIC

Industrial PC, Industrial monitor

SIMATIC IPC277D/E 19" INOX PRO,

SIMATIC IFP1900 INOX PRO

Service Manual

11/2017

A5E35751762

-AC

Preface

Overview

Safety instructions

Replacing the seal of the

compartment cover

Extended maintenance work

Accessories and spare parts

Technical support

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E35751762-AC

Ⓟ

11/2017 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

Service Manual, 11/2017, A5E35751762-AC 3

Preface

Validity

This document applies to devices with the designation IPC277D/E 19" INOX PRO and

IFP1900 INOX PRO with the following article numbers:

Article number

Device

6AV7484-4AB00-0AA0 IPC277D 19" INOX PRO, stand mounting (with operator controls)

6AV7484-4AB10-0AA0

IPC277D 19" INOX PRO, support arm mounting (with operator controls)

6AV7484-5AB00-0AA0 IPC277E 19" INOX PRO, stand mounting (without operator controls)

6AV7484-5AB10-0AA0

IPC277E 19" INOX PRO, support arm mounting (without operator controls)

6AV7484-6AB00-0AA0

IFP1900 INOX PRO, stand mounting (with operator controls)

6AV7484-6AB10-0AA0

IFP1900 INOX PRO, support arm mounting (with operator controls)

6AV7484-6AB01-0AA0

IFP1900 INOX PRO, stand mounting (without operator controls)

6AV7484-6AB11-0AA0

IFP1900 INOX PRO, support arm mounting (without operator controls)

Conventions

The term "device" is also used instead of the product designation in this document.

Figures

This document contains figures of the device described. The figures can deviate from the

particularities of the delivered device.

Steps in the figures are identified with process numbers according to the sequence in which

they have to be executed: , , , ...

A device for stand mounting is shown as an example in the figures. The steps can be

executed in the same way for a device for support arm mounting.

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

4Service Manual, 11/2017, A5E35751762-AC

Table of contents

Preface........................................................................................................................................ 3

1 Overview ..................................................................................................................................... 5

2 Safety instructions......................................................................................................................... 6

3 Replacing the seal of the compartment cover ................................................................................... 7

4 Extended maintenance work .......................................................................................................... 9

4.1 Overview............................................................................................................................10

4.2 Opening the device and loosening cables...........................................................................12

4.3 Replacing the seal of the rear panel ...................................................................................14

4.4 Replacing operator controls................................................................................................16

4.5 Changing the mounting type...............................................................................................19

4.6 Fastening the rear panel.....................................................................................................21

5 Accessories and spare parts ........................................................................................................ 23

A Technical support........................................................................................................................ 25

A.1 Service and support ...........................................................................................................25

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

Service Manual, 11/2017, A5E35751762-AC 5

Overview

The INOX PRO devices are available with or without operator controls on the front and are

intended for "stand mounting" or "support arm mounting". The figure below shows the front

view using a device with operator controls as an example.

①

Illuminated pushbutton

"left" with green LED

⑤

Terminal compartment cover with seal

②

Illuminated pushbutton

"right" with red LED

⑥

Rear panel with seal

③

EMERGENCY OFF button

⑦

Mounting kit for support arm mounting

④

Mounting kit for stand mounting

This document describes the following maintenance work:

●Replacing the seal of the compartment cover

●Replacing defective operator controls in the device front and LEDs 1

●Replacing the seal of the rear panel

●Changing the mounting type, which means converting a device for stand mounting into a

device for support arm mounting and vice versa.

1Only for devices with operator controls

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

6Service Manual, 11/2017, A5E35751762-AC

Safety instructions

WARNING

Extended maintenance work may only be carried out by qualified and correspondingly

trained personnel

The Service Manual describes extended maintenance work, among other things. The

device is opened as part of the extended maintenance work with work to take place on the

wiring or on electronic components inside the device. Injuries or material damage may

result if the work is not carried out correctly.

The maintenance work described in the Service Manual may only be carried out by

qualified specialist personnel who have been trained correspondingly by Siemens.

WARNING

IP66 degree of protection

The device has IP66 degree of protection when it is closed. If the seals are not inserted

correctly during maintenance work or if the device is not closed properly, IP66 degree of

protection is no longer guaranteed. Humidity may penetrate the device. The result may be

damage to the device and personal injury.

Make sure you follow the instructions in this document precisely when replacing the seals.

Make sure that the seals are inserted correctly and that the covers are fastened properly.

Storage and transport

NOTICE

Damage from condensation

If the device is subjected to extreme changes in temperature during transportation, for

example, in the case of cold weather, moisture can built up on and in the device. Moisture

can result in short-circuits in electrical circuits.

The device no longer works correctly.

In case of condensation, you need to store the device in a dry place and slowly warm it up

to room temperature. However, do not expose the device to direct heat radiation. Wait

12 hours before you switch on the device.

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

Service Manual, 11/2017, A5E35751762-AC 7

Replacing the seal of the compartment cover

WARNING

IP66 degree of protection

The device has IP66 degree of protection when it is closed. If the terminal compartment

seal is not inserted correctly or if the terminal compartment is not closed properly, IP66

degree of protection is no longer guaranteed. Humidity may penetrate the device. The

result may be damage to the device and personal injury.

Make sure you follow the instructions in this document precisely when replacing the seal.

Make sure that the seal is inserted correctly and that the terminal compartment cover is

fastened properly.

Requirement

You need the service pack with article number 6AV7675-1JD20-0AA0.

Procedure

Note

The description below shows figures of a device

that is not mounted on the stand.

You can replace the seal of the terminal compartment cover even when the device is

mounted on a stand or support arm.

Replacing the seal of the compartment cover

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

8Service Manual, 11/2017, A5E35751762-AC

1. Remove the six screws of the terminal compartment cover.

2. Remove the terminal compartment cover.

CAUTION

Do not drop the terminal compartment cover

Dropping the terminal compartment cover may result in minor injuries or damages to the

device.

Prevent the terminal compartment cover from dropping, especially when it is mounted

on a stand or support arm.

3. Remove the seal of the terminal compartment cover.

4. Insert the spare seal as shown in the figure.

5. Check the seal for correct seat; make sure that the bore holes of the seal enclose the

collar of the press-fit components, see marked locations.

6. Place the terminal compartment cover on the terminal compartment and reinsert the

six screws.

7. Tighten all six screws with a torque of 3.5 Nm.

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

Service Manual, 11/2017, A5E35751762-AC 9

Extended maintenance work

WARNING

Opening the device and working on the opened device may only be carried out by qualified

and correspondingly trained personnel

The service manual describes, amongst other points, the opening of the device and

working on the wiring or on electronic components in the inside of the device. Injuries or

material damage may result if the work is not carried out correctly.

The work described in the service manual may only be carried out by qualified specialist

personnel who have been trained correspondingly by Siemens.

WARNING

After opening the device, you must replace the seal of the rear panel

The device has IP66 degree of protection when it is closed. If the seal of the rear panel is

not replaced after opening the device, the tightness of the device is not guaranteed.

Humidity may penetrate the device. This can result in personal injury or material damage.

Always replace the seal of the rear panel when you open the device. Make sure you follow

the instructions in this document precisely when replacing the seals. Make sure that the

seals are inserted correctly and that the covers are fastened properly.

NOTICE

Use only approved spare parts

Installation of spare parts which are not approved for this device can damage the device,

machine or plant. The warranty becomes void if you use spare parts that are not approved.

Only use spare parts from a service pack, from a mounting kit or operator controls

according to the specification in section "Accessories and spare parts (Page 23)".

Devices with operator controls on the front

NOTICE

Placing the device on its front can damage operator controls

If you place the device on its front before or during the installation, the operator controls on

the front can be damaged.

Place the device on a soft and elevated surface so that the front operator controls do not

contact the working area and are not damaged.

Extended maintenance work

4.1 Overview

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO

10 Service Manual, 11/2017, A5E35751762-AC

Components sensitive to electrostatic charge

Electrostatic sensitive devices are labeled with an appropriate symbol.

NOTICE

Electrostatic sensitive devices (ESD)

The device includes electrostatic sensitive devices. When you touch electrostatic sensitive

devices, you can destroy them through voltages that are far below the human perception

threshold.

When you open the device you must take appropriate ESD measures, for example:

•When handling electrostatic sensitive devices, make sure that persons, the workstation

and devices, tools and packaging used are properly grounded. This way you avoid static

charging.

•Discharge your body electrostatically before you take a measurement at a module. Do

so by touching grounded metallic parts. Always use grounded measuring instruments.

•Avoid direct contact.

•As a general rule, do not touch electrostatic sensitive devices, except in the case of

unavoidable maintenance work.

•Hold the modules at their edge so that you do not touch the connector pins or conductor

paths. This way, the discharge energy does not reach and damage the sensitive

components.

4.1

Overview

This section describes the following extended maintenance work:

●Replacing the seal of the rear panel

You need service pack 2 with article number 6AV7675-1JD21-0AA0.

●Changing the mounting type, which means converting a device for stand mounting into a

device for support arm mounting and vice versa.

You need service pack 2 with article number 6AV7675-1JD20-0AA0.

Note

When you change the mounting type, you need the corresponding mounting kit for

mounting, see section "

Accessories and spare parts (Page 23)".

●Only for devices with operator controls: Replacing defective operator controls in the

device front and LEDs

You need the corresponding spare parts, see section "Accessories and spare parts

(Page 23)".

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Industrie-PC Handbücher

Siemens

Siemens SIMATIC IPC377G Bedienungsanleitung

Siemens

Siemens SIMATIC Rack PCs Administratorhandbuch

Siemens

Siemens Simatic IPC520A Bedienungsanleitung

Siemens

Siemens SIMATIC IPC477D Bedienungsanleitung

Siemens

Siemens SIMATIC IPC427C Bedienungsanleitung

Siemens

Siemens SIMATIC IPC547C Bedienungsanleitung

Siemens

Siemens SIMATIC IPC227G Bedienungsanleitung

Siemens

Siemens SIMATIC HMI IPC677C Bedienungsanleitung

Siemens

Siemens SIMATIC IPC227G Bedienungsanleitung

Siemens

Siemens SIMATIC IPC427D Bedienungsanleitung

Siemens

Siemens SIMATIC IPC PX-32A Bedienungsanleitung

Siemens

Siemens SIMATIC IPC1047E Bedienungsanleitung

Siemens

Siemens SIMATIC IPC277E Bedienungsanleitung

Siemens

Siemens SIMATIC IPC PX-39A Bedienungsanleitung

Siemens

Siemens SIMATIC IPC DiagMonitor V5.1.6 Bedienungsanleitung

Siemens

Siemens SIMATIC IPC347G Bedienungsanleitung

Siemens

Siemens SIMATIC PCS 7 BOX Stücklistenhandbuch

Siemens

Siemens SIMATIC IPC BX-39A Bedienungsanleitung

Siemens

Siemens Simatic IPC547G Bedienungsanleitung

Siemens

Siemens SIMATIC PCIe DIO4 Administratorhandbuch

Siemens

Siemens SIMATIC IPC277E Bedienungsanleitung

Siemens

Siemens SIMATIC HMI IPC677C Bedienungsanleitung

Siemens

Siemens SIMATIC Rack PC 840 V2 Bedienungsanleitung

Siemens

Siemens SIMATIC IL43 Bedienungsanleitung

Beliebte Industrie-PC Handbücher anderer Marken

Chipsee

Chipsee PPC-A72-101 Bedienungsanleitung

Advantech

Advantech UNO-2184G Bedienungsanleitung

MSI

MSI MS-9A76 Bedienungsanleitung

Stackrack

Stackrack THOR200 Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-682C Series Bedienungsanleitung

Nodka

Nodka eBOX-3000-ETC Bedienungsanleitung

Artila

Artila Matrix-516 Bedienungsanleitung

MSI

MSI MS-9A89 Bedienungsanleitung

Advantech

Advantech IPPC-6152A Bedienungsanleitung

Beckhoff

Beckhoff CX9020 Bedienungsanleitung

Dell

Dell Embedded Box PC 5000 Bedienungsanleitung

IBASE Technology

IBASE Technology ASB200-918 Series Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M90q Betriebsanleitung

IXXAT

IXXAT Econ 100 Bedienungsanleitung

Kontron

Kontron KBox A-151-TGL Bedienungsanleitung

AXIOMTEK

AXIOMTEK ICO500-518 Series Bedienungsanleitung

JLT

JLT 1214N Bedienungsanleitung

Beckhoff

Beckhoff C6925 Bedienungsanleitung