Siemens FDCI183 Bedienungsanleitung

FDCI183 Transponder

Product Manual

Characteristic

Fulfill Chinese Standard of GB16806-2006 “Interlocking Control System”;

1 monitored inputs as collective detector connection;

LED display of alarm and fault status;

External 24VDC power supply;

Microprocessor-controlled signal evaluation;

Earth fault monitoring;

With the Zener diode barrier, it is also possible to connect intrinsically safe detectors;

Applicable in dry, dusty and humid areas in protection box.

Application

From a functional perspective, we distinguish between the primary side and the secondary side of the transponder.

The primary side is the connection to the FD18-BUS. The secondary side is the connection to the collective

detection line.

Compatible detector list

Type Max. detector per line

HI520/OP520

DO1101A-EX/DT1101A-EX

DF1101-EX 5

FDL241-9-CN/DF1191/DF1192

FDO181C/FDT181C 32

Communication

The communication with the control panel is performed via the FD18-BUS. The configuration is performed on

the control unit or commissioning tool.

Power Supply

Power supply of the primary side (FD18-BUS) is always ensured via the detector line FD18-BUS. Power

supply of the secondary side must always be ensured via an external 24VDC supply unit. The primary and

the secondary side are galvanically isolated.

Operating modes

The transponder can be in either of the following operating modes:

Building Technologies

A6V10362122_a_en_--

Fire Safety & Security Products 12.2011



Normal operation



Localization

Normal operation

The transponder is in the intended operating mode. Inputs are monitored and assessed.

Localization

For an unambiguous identification, the transponder can be set in localization mode from the control unit. The

localization mode is indicated by the LED.

Earth fault monitoring

The earth fault monitoring function can be switched off with a jumper. When the earth fault monitoring is switched

on, the terminal of earth connection should be connected with grounding. When intrinsically safe detectors are

connected, the earth fault monitoring must be switched off.

Structure

No.

Signification

1 Connection to collective detector line

2 Earthing connection

3 Jumper for the earth fault monitoring

4 LEDs for the status indication of alarm

5 LEDs for the status indication of fault

6 Connection of the FD18-BUS line

7 Connection of the 24V external power supply

LED Indicators

Red Yellow Signification

off off Normal condition

flashes every 1 s off Localization mode

on off Alarm mode

off flashes every 4 s Short mode

off flashes every 41s Open mode

off on Fault mode

Jumper

Position Signification

ON Earth fault monitoring is activated

OFF Earth fault monitoring is deactivated(default)

Building Technologies

A6V10362122_a_en_--

Fire Safety & Security Products 12.2011

Installation

Fig. 2

Fig. 3

Fig. 4

Fig.

Fig. 8 Detection line connection

Fig. 9 Detector line with safety barrier

(

the earth fault monitoring must be switched off)

Preparation

Voltage!

No power supply during installation.

1. Determine type of installation:

– Installation outside a switching cabinet or a control unit:

use FDCH221 housing (Fig. 3) .

– Installation directly in a switching cabinet or a control

unit: mount the module on an even surface (Fig. 2) .

Procedure with installation on an even surface

1. Put the transponder on an even surface.

2. Fix it with two M4 screws (Fig. 2). Distance between

installation holes:

118.0

1.0mm

。

Procedure with installation in the housing

1. Open the housing (Fig. 6).

Determine the cable entries in the housing and break them

out.

3. Mount the housing on an even surface with two M4

screws

(Fig. 4). Distance between holes: 182.0

1.0mm.

4. Insert the cables and fix the cables in the housing (Fig. 5).

5. Insert the seal and fix the lid additionally with four screws

(Fig. 6). (only this way is IP65 protection guaranteed)

Electric connection

Input voltage should not be less than 18VDC.

Mind the positive and negative polar when connecting the

diodes.

Connect only

one

wire per terminal.

1. Connect the cables to the terminals according to the

connection diagram (Fig. 7, Fig. 8, Fig. 9).

2. Connect the line terminators (EOL). These must be

connected to the end of the line (Fig. 8 /Fig. 9).

3. Connect the cables to the module with cable ties (max.

width 2.6 mm).

I/O

FDCI183

EOL

1.5KE20CA

Beijing Siemens Cerberus Electronics Limited

No.1,Fengzhidonglu, Xibeiwang, HaiDian District,

Beijing, 100094, China

Tel: +10 6476 8806

Fax: +10 6476 8899

Doc No. A6V10362122_a_en_-- Version a Manual FD18

Edition 12.2011

101082423

Dimensions

In:mm

Specification

FD18-BUS Operating voltage 12... 33 VDC

FD18-BUS Operating current Quiescent: 0.45mA

Alarm:1.1mA

External power supply

–

Input voltage

18... 32 VDC @ 0.15A

End of line 1.5KE20CA(EOL) or EOL22(ex)

Operating temperature –10... +50 °C

Storage temperature –30... +70 °C

Humidity ≤95 % rel.

Communication protocol FD18-BUS

Load factor 3

Connectable terminal blocks 0.2... 2.5 mm

Color

–

Housing

–

Cover

Pure white, RAL 9010

transparent matt

Protection category EN60529 /

IEC529

–

with auxiliary housing

IP65

Line impedance of collective

detection line

150ohm (twins cable)

Order Information

Type Material No. Part No. Designation Weight

FDCI183 Transponder,Incl.1.5KE20CA(EOL) 0.098 Kg

FDCH221 S54312-F3-A1 100686595 Auxiliary Housing (IP65) 0.250 Kg

SB3 100208657 Safety barrier

EOL22(ex) 100211529 End of Line

1.5KE20CA(EOL) A5Q00015836 100967645 Transient Diode 20V

Andere Siemens Seefunkgerät Handbücher

Siemens

Siemens SIMATIC RTLS4030T Anwendungshandbuch

Siemens

Siemens SIMATIC RTLS4060T Bedienungsanleitung

Siemens

Siemens SIMATIC RTLS4060T Bedienungsanleitung

Siemens

Siemens SIMATIC RTLS4084T Bedienungsanleitung

Siemens

Siemens SIMATIC RF645T Administratorhandbuch

Siemens

Siemens SIMATIC RTLS4083T Bedienungsanleitung

Siemens

Siemens SAT 12 Bedienungsanleitung

Siemens

Siemens SIMATIC RF610T Benutzerhandbuch

Siemens

Siemens SIMATIC RTLS4083T Anwendungshandbuch

Siemens

Siemens SIMATIC RTLS4460T Bedienungsanleitung

Beliebte Seefunkgerät Handbücher anderer Marken

Garmin

Garmin GTX 45R Bedienungsanleitung

Garmin

Garmin GTX 33 Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane TT-6222A VHF DSC Bedienungsanleitung

Garmin

Garmin VHF 315 Series Bedienungsanleitung

Vesper

Vesper Cortex HV1 Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane Sailor RT5022 VHF DSC Bedienungsanleitung

Saab

Saab R5 SUPREME AIS Bedienungsanleitung

AMEC

AMEC CAMINO-701 Bedienungsanleitung

GME

GME GX800 Bedienungsanleitung

West Marine

West Marine VHF580 Bedienungsanleitung

Uniden

Uniden UM425 VHF DSC Bedienungsanleitung

ACR Electronics

ACR Electronics AISLink CB2 Bedienungsanleitung

Barco

Barco MDSC-2226 Bedienungsanleitung

Blue Mark

Blue Mark DroneBeacon 120 Series Bedienungsanleitung

Simrad

Simrad DSC1400 Bedienungsanleitung

Raveon

Raveon RV-M8G Bedienungsanleitung

Trig Avionics

Trig Avionics TT31 Bedienungsanleitung

Uniden

Uniden UM380 Bedienungsanleitung