Siemens SIREMOBIL Compact L Bedienungsanleitung
Siremobil Compact L
English
Print No.: SPR2-130.841.03.02.02 Doc. Gen. Date: 06.05
Replaces: SPR2-130.841.03.01.02
© Siemens AG 2005
The reproduction, transmission or
use of this document or its contents
is not permitted without express
written authority. Offenders will be
liable for damages. All rights,
including rights created by patent
grant or registration of a utility
model _or_design,_are_reserved.
SP
Replacement Instructions
15" TFT Display 71 42 354
Siremobil Compact L SPR2-130.841.03 Page 2 of 20 Siemens AG
Rev. 02 06.05 CS PS 24 Medical Solutions
2 Replacement of the 15" LCD Color TFT Display 1
Document revision level 1
The document corresponds to the version/revision level effective at the time of system
delivery. Revisions to hardcopy documentation are not automatically distributed.
Please contact your local Siemens office to order current revision levels.
Disclaimer 1
The installation and service of equipment described herein is to be performed by qualified
personnel who are employed by Siemens or one of its affiliates or who are otherwise
authorized by Siemens or one of its affiliates to provide such services.
Assemblers and other persons who are not employed by or otherwise directly affiliated
with or authorized by Siemens or one of its affiliates are directed to contact one of the
local offices of Siemens or one of its affiliates before attempting installation or service pro-
cedures.
Replacement of the 15" LCD Color TFT Display 3
Siemens AG SPR2-130.841.03 Page 3 of 20 Siremobil Compact L
Medical Solutions Rev. 02 06.05 CS PS 24
Notes and symbols 1
Emphasized texts in technical documentation have the following meaning:
DANGER indicates an immediate danger that if disregarded will
cause death or serious physical injury.
WARNING indicates a possible danger that if disregarded can
cause death or serious physical injury.
CAUTION used with the safety alert icon indicates a possible dan-
ger that if disregarded will or can lead to minor or moderate phys-
ical injury and/or damage to property.
NOTICE used without the safety alert icon indicates a possible
danger that if disregarded may or will lead to an undesirable
result or state other than death, physical injury or property
damage.
DANGER
WARNING
CAUTION
NOTICE
Siremobil Compact L SPR2-130.841.03 Page 4 of 20 Siemens AG
Rev. 02 06.05 CS PS 24 Medical Solutions
4 Replacement of the 15" LCD Color TFT Display
Validity of these instructions 1
These instructions are valid for the replacement of the 15" LCD Color TFT Display,
part no. 07142354.
Required documents 1
•System manual and Service instructions of the system.
Required tools, measurement and auxiliary devices 1
Available spare parts 1
The following spare parts are available:
All tools, measurement and auxiliary devices with the exception
of those marked "*", are listed along with their specifications in
the STC (Service Tools Catalogue).
•Protective conductor meter (e.g. Safety tester UNIMET 1100 ST, part no. 51 38 727)
•To o l k i t *
•1 set Allen keys*
•Luminance meter (e.g. SMfit Kit luminance meter, part no. 88 81 281)
Part description Part number Remarks
15" LCD Color TFT Display (REP) 07142354 External switched-mode power supply
is included in the repair kit.
230V ~ Power cable not included.
External switched-mode power
supply
07141083 230V ~ Power cable not included.
Display holder 07142347 Fastening screws not included
NOTE
Replacement of the 15" LCD Color TFT Display 5
Siemens AG SPR2-130.841.03 Page 5 of 20 Siremobil Compact L
Medical Solutions Rev. 02 06.05 CS PS 24
Safety Information 1
Risk of physical injury or death and property damage!
Observe
- the product-specific safety information in these instructions
and the service instructions of the product,
- the general safety information in the instructions
TD00-000.860.01... and
- the general safety information according to ARTD Part 2.
Noncompliance can lead to death, physical injury or property
damage.
Electrical voltage
Certain components inside the TFT Display are under
high voltage!
Do not open the TFT Display housing! This is not necessary in a
service situation.
Do not insert objects into the TFT Display housing!
Electrical voltage!
Noncompliance can lead to death, physical injury or property
damage.
After completing all service work and attaching all system covers,
you must perform a protective ground wire test according to
ARTD-002.731.17... .
The protective ground wire resistance must not exceed 0.2 ohms.
Risk of being burned by hot parts or components!
Noncompliance can lead to light or medium burns, especially of
the hands.
Once the covers have been removed, parts or components (e.g.
power components, heat sinks, solenoid brakes) become acces-
sible which may exhibit temperatures of up to 50°C in operation.
To prevent burns, switch off the system power supply before con-
tacting any parts or components and let the system cool off for at
least 5 minutes before resuming work.
Electrical voltage!
Noncompliance can lead to property damage.
ESD protection guidelines must be observed when servicing.
WARNING
WARNING
WARNING
CAUTION
CAUTION
Siremobil Compact L SPR2-130.841.03 Page 6 of 20 Siemens AG
Rev. 02 06.05 CS PS 24 Medical Solutions
6 Replacement of the 15" LCD Color TFT Display
Operating key switches 1
Unlocking / Locking the OSD Menu 1
Locking or unlocking is performed with the same work steps.
•Switch off the display.
•During power on, press and hold the keys "UP" and "DOWN" simultaniously
for approx. 10 seconds.
If the OSD menu was locked, the message "OSD is locked" is displayed.
POWER 1
TFT Display on or off.
MENU 1
Opens or closes the OSD menu.
The OSD menus are described in the user manual of the TFT Display.
The OSD menu will be closed automatically after 20 seconds.
The key switches are fitted on the back of the TFT display.
Name of key OSD not active OSD active
MENU Open
OSD menu
Exit
OSD menu
ENTER Enter
function
POWER TFT Display
ON/OFF
UP Search
Video Input
Increase
value
DOWN
Search
Video Input
Decrease
value
For the adjustments, set the OSD time to "Off"
(permanent visible OSD menu) by selecting the OSD menu
"Options" - "Onscreen Menu" - "OSD Time".
After the adjustments, set it back to the default value (20 seconds)
NOTE
NOTE
Replacement of the 15" LCD Color TFT Display 7
Siemens AG SPR2-130.841.03 Page 7 of 20 Siremobil Compact L
Medical Solutions Rev. 02 06.05 CS PS 24
ENTER 1
Selects the available sub menu or parameter.
If the parameter was changed, the enter key confirms the selected value and returns to
the previous displayed OSD menu.
UP / DOWN 1
If the OSD menu is inactive (not visible), pressing the key selects the automatic search of
a video signal at the video input connectors.
If the OSD menu is active, pressing the key up or down scrolls though the available menu
items of the OSD menu (highlighted in blue)
or changes the available parameter value (if highlighted in red).
Troubleshooting 1
External switched-mode power supply 1
•Measure the output voltage, printed on the external switched-mode power supply.
•It can also be checked by swapping the low voltage connectors from one to the other
installed TFT display.
TFT Display 1
•Depending on the malfunction, ensure that the display is the defective part.
- Check the switched-mode power supply.
- Check the connectors (low voltage input, video signal input)
- Check the video signal of the MEMOSKOP with the SMPTE test pattern
(300mV Sync +/- 10%, 1Vss +/- 10% (in 100% peak white field)).
- Check the input selection switch (at the bottom side of the TFT display).
The switch can be set in 3 positions:
1. Position to the rear: VGA input selected
2. Middle position: BNC-Input selected, 75Ohm termination resistor is off.
3. Position to the front: BNC input selected, 75 Ohm termination resistor is on.
- Check the settings of the on screen menu, in accordance with the user manual.
The TFT display includes no repairable parts and has to be
changed completely if defective.
NOTE
Siremobil Compact L SPR2-130.841.03 Page 8 of 20 Siemens AG
Rev. 02 06.05 CS PS 24 Medical Solutions
8 Replacement of the 15" LCD Color TFT Display
Replacements 1
Replacing the display holder 1
•Unplug all connectors from the display(s).
•Loosen the display(s) from its(their) holders (4 screws each, see 1 / Fig. 1).
•Unscrew the holder from the monitor cart (3 / Fig. 1).
•Install the new holder on the monitor cart.
•If 2 TFT displays are present, install the extension plate on the holder and fix it in the
position, shown in Fig. 1 with the 4 screws 2 / Fig. 1.
•Install the display(s) on the holder (1 / Fig. 1).
•Reconnect the low voltage connector and video signal connector to each TFT display.
•Check the functions of the TFT displays.
Fig. 1
Replacement of the 15" LCD Color TFT Display 9
Siemens AG SPR2-130.841.03 Page 9 of 20 Siremobil Compact L
Medical Solutions Rev. 02 06.05 CS PS 24
Replacing the switched-mode power supply 1
•Disconnect the low voltage plug from the TFT display.
•Disconnect the power plug of the switched-mode power supply.
•Loosen the cable ties of the low voltage cable and pull it back to the log book
compartment.
•Take out the switched-mode power supply from the log book compartment.
•Install the new switched-mode power supply in the log book compartment, using new
cable ties.
•Install the low voltage cable to the TFT display and connect it.
•Fix the low voltage cable with cable ties.
•Connect the power plug to the switched-mode power supply.
•Check the function of the TFT display.
The switched-mode power supplies are installed in the log book
compartment and are fixed with cable ties.
Fig. 2
NOTE
Siremobil Compact L SPR2-130.841.03 Page 10 of 20 Siemens AG
Rev. 02 06.05 CS PS 24 Medical Solutions
10 Replacement of the 15" LCD Color TFT Display
Replacing the TFT display 1
•Disconnect the low voltage plug from the TFT display
•Disconnect the VGA plug from the TFT display.
•Loosen the 4 screws at the rear side of the TFT display and remove it from the holder
•Install the new display with the 4 mounting screws.
•Connect the low voltage plug and the VGA plug at the new display.
•Check the input selection switch (at the bottom side of the TFT display).
The switch can be set in 3 positions:
Position to the rear: VGA input selected
- Set this position, if VGA video cables are used.
Middle position: BNC-Input selected, 75 Ohm terminating resistor is off.
- Set this position only, if additional video components are installed at the same video
source as the TFT display.
Position to the front: BNC input selected, 75 Ohm terminating resistor is on.
- Set this position, if BNC video cable is used and no additional video component is
installed at the same video source as the TFT display is connected.
•Check the functions of the TFT displays.
•Check the automatically detected video mode.
•Check the geometry of the displayed image.
•Adjust the brightness, contrast and back light intensity.
Hold the TFT display while loosening the mounting screw to
prevent damage to the TFT display or the environment
Fig. 3
NOTE
Andere Handbücher für SIREMOBIL Compact L
2
Inhaltsverzeichnis
Andere Siemens Monitor Handbücher
Siemens
Siemens PBC Bedienungsanleitung
Siemens
Siemens SMD21300 Bedienungsanleitung
Siemens
Siemens MCM 1902 Bedienungsanleitung
Siemens
Siemens SITRANS RD100 Leitfaden
Siemens
Siemens SCD 1515-E Bedienungsanleitung
Siemens
Siemens SISTORE AX9 Bedienungsanleitung
Siemens
Siemens SIMATIC S7-200 Benutzerhandbuch
Siemens
Siemens CMTC1720 Bedienungsanleitung
Siemens
Siemens SMD 18101 CS Bedienungsanleitung
Siemens
Siemens 43B1-M Bedienungsanleitung
Siemens
Siemens SCD 1597-E Bedienungsanleitung
Siemens
Siemens SIMOMED HM Betriebsanleitung
Siemens
Siemens MCF 3501 T Bedienungsanleitung
Siemens
Siemens SIMATIC HMI series Bedienungsanleitung
Siemens
Siemens SITRANS RD200 Bedienungsanleitung
Siemens
Siemens 175V Bedienungsanleitung
Siemens
Siemens 125-2134 Bedienungsanleitung
Siemens
Siemens SCD 1997-E Bedienungsanleitung
Siemens
Siemens 19T2 Bedienungsanleitung
Siemens
Siemens FT2014 Bedienungsanleitung
