Siemens SIPROTEC 4 Bedienungsanleitung

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 1 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

Remote Control SIPROTEC 4 via Ethernet-Modems 7XV585x and 7XV5655

General

In principle the scope of functions of Ethernet-Modems correspond to the already known analog or

digital telephone modems. Instead of the analog or digital telephone network, the transmission

medium is the well-known Ethernet. For this purpose, the data received at the RS232-interface are

packed into a TCP/IP-protocol and unpacked again at the opposite end for output on the RS232-

interface .Instead of a telephone number, the connection is established from the calling Ethernet

modem (office modem) by selection of an IP address.

This method allows for the simple handling of Ethernet modems by the protection communication

program DIGSI 4 if the following application guidelines are strictly adhered to.

The example outlines a small private network with free IP addresses. The operating PC with

Windows XP and DIGSI 4.50 in this case has a fixed IP address 192.168.10.100. The office modem

has the IP address 192.168.10.161, the substation modems 192.168.10.153 and 192.168.10.154.

Note: This application guide only serves as a additional user information and assumes that the user

has knowledge of the general application guide for the product and its basic functions as described in

the manual.

Approach:

•• Installing modem driver in Windows

•• Configuring modems with the configuration tool

oSelecting basic data (IP-address and name) of the office modem

oSelecting basic data (IP-address and name) of the substation modem

oIntegration of-PC and Ethernet-Modems into the Ethernet

oSelecting the communication parameters (Baud rate, data format etc.) of the office modem

oSelecting the communication parameters (Baud rate, data format etc.) of the substation

modem

•Inserting telephone directory and modems in the substation manager of DIGSI 4

oInsert telephone directory with IP addresses

oInsert office and substation modem with settings

oInsert modem connection

•Establish the modem connection

oStart the connection

oCheck the “number” to be dialled (IP address), correct of necessary

oCheck the connection in the report window

oEstablishment of connection to the protection device

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 2 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

Installation of the modem driver

For the operation of an Ethernet modem in a Windows application, it is necessary to install a modem

driver in the Control panel of Windows.

The operating systems Windows NT 4 from SP6a, Windows 2000 or Windows XP (Professional) are

a pre-requisite for this.

The modem driver ipetherModem.inf for the Ethernet-modem may be found on the included CD

„Manuals 7XV5“ under „Accessories / 7XV585x / Driver“.

NOTE! Up-to-date information may be found in the Internet under

www.SIPROTEC.com under Accessories / 7XV585x or applications / remote-control

In the Control panel

Choose „Telephone- and Modem

options“

By double-clicking on the icon.

ADD installs a new modem driver in Windows.

If a modem driver has not yet been installed, Windows

automatically offers an installation window.

Continue with OK.

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 3 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

The modem must be selected manually.

For this purpose a check is placed in the

field

Select modem

(no automatic detection)

Press Next >.

Install a new modem from

Have Disk…

Select the correct Drive

And search for the modem driver in the

storage medium

Browse…

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 4 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

The modem driver is located on the

Manuals 7XV5

path

Accessories / 7XV585x / Driver / …

and

Open

Select the driver file

ipetherModem.inf and

Open

Confirm with

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 5 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

Mark the modem model.

Siemens – ipEtherModem

It may be ignored that this driver has no

digital signature.

Next >

Select the serial connection,

e.g. COM1

to which the Ethernet modem will later

be connected.

Next >

This warning from Windows XP may be

ignored. The driver was tested with

Windows XP.

Continue with

Continue Anyway

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 6 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

The installation is completed with

Finish

Overview of the modem drivers installed

in Windows.

With Properties the settings of the

marked modems may be checked and

changed.

The maximum baud rate to the terminal

device may be set here.

This baud rate is set to 57600 Bd for

all applications and may not be

changed.

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 7 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

In the area “Advanced“ no „further

initialising commands“ need to be

entered.

These additional commands are later

entered in DIGSI 4.

No settings need to be made under

“Alter standard settings“.

For control purposes the standard settings may be

opened.

The setting „57600“ and „ (8N1)“

should be used for all applications.

Please do not change this!

Close all Windows with „OK“ and

Restart the PC.

Note: The settings of the modem driver are accepted by DIGSI 4 and are then used by the

office modem during the dial-up process.

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 8 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

Setting Ethernet-modems with the configuration tool

All modems are factory pre-set on delivery; this setting must be adapted to the individual

applications. This may in principle be done with a terminal program via the RS232 interface,

the simplest method however being the use of the configuration tool on a PC which is

connected to an Ethernet modem with a crossed patch cable.

The installation of the configuration tools is described at length in the Ethernet modem

manual; the crossed path cable is included in the scope of delivery.

When the Ethernet modem is supplied with auxiliary voltage and connected to the operating

PC via the crossed patch cable, the configuration tool is started. The modem should be

found immediately after the start.

Note: In this example, the operating PC is allocated with fixed addresses.

IP-address: 192.168.10.100

Sub-net mask: 255.255.255.0

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 9 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

Allocating an IP-address and name to the Office Modem

In the private network (LAN) or the public network the Ethernet-modem must be allocated with an

own, unique IP address.

Click on the pre-set IP address (10.10.5.1) with the right mouse button. An option box is opened.

Select “Set IP” in the option box, enter the new IP address (here 192.168.10.161)

and confirm with “OK”.

Select “Set Name“ in the option box, enter the modem name (here Office) and confirm with “OK“.

If the settings are confirmed with “OK“ they are saved in the Ethernet-modem. The information

window is up-dated automatically and the Ethernet-modem with its new settings is displayed.

Following a Restart of the configuration tool, the modem with its current settings is located and

displayed. In the column “Ping OK“ and „in local Net“ the displayed “True“ confirms that the modem is

now located in the same network segment as the operating PC and that it answers to a “Ping”. The

column “Logged in“ is „True“ confirms that other modem parameters may also be set at this point.

HELP_DIG4_SIP4_ETHERNET_A2.DOC Seite 10 von 21 28.11.2005

Power Transmission and Distribution

Energy Automation

Allocating a name and IP-address to the “Substation modem”

In the private network (LAN) or the public network the Ethernet-modem must be allocated with an

own, unique IP address

Click on the pre-set IP address (10.10.5.1) with the right mouse button. An option box is opened.

Select “Set IP” in the option box, enter the new IP address (here 192.168.10.153)

and confirm with “OK”.

Select “Set Name“ in the option box, enter the modem name (e.g. distributor east)

and confirm with “OK“.

If the settings are confirmed with “OK“ they are saved in the Ethernet-modem. The information

window is up-dated automatically and the Ethernet-modem with its new settings is displayed.

Following a fresh start of the configuration tool, the modem with its current settings is located and

displayed. In the column “Ping OK“ and „in local Net“ the displayed “True“ confirms that the modem is

now located in the same network segment as the operating PC and that it answers to a “Ping”. The

column “Logged in“ is „True“ confirms that other modem parameters may also be set at this point

(refer to the following chapters).

Andere Handbücher für SIPROTEC 4

Inhaltsverzeichnis

Andere Siemens Fernbedienung Handbücher

Siemens

Siemens 5ST3071 Bedienungsanleitung

Siemens

Siemens 5WK49266 Bedienungsanleitung

Siemens

Siemens SVI-HMFNA04 Bedienungsanleitung

Siemens

Siemens 5WG1 255-7AB01 Service-Handbuch

Siemens

Siemens 3AD8 Bedienungsanleitung

Siemens

Siemens miniTek Bedienungsanleitung

Siemens

Siemens ePen Bedienungsanleitung

Siemens

Siemens 5ST3050 Bedienungsanleitung

Siemens

Siemens TEK Connect Bedienungsanleitung

Siemens

Siemens 5ST3053 Bedienungsanleitung

Siemens

Siemens IRA211 Bedienungsanleitung

Siemens

Siemens DELTA reflex Service-Handbuch

Siemens

Siemens easyPocket Bedienungsanleitung

Siemens

Siemens easyPocket Bedienungsanleitung

Siemens

Siemens TEK Connect Bedienungsanleitung

Siemens

Siemens RCC-3 Bedienungsanleitung

Siemens

Siemens ProPocket Bedienungsanleitung

Siemens

Siemens miniTek Bedienungsanleitung

Siemens

Siemens SIRIUS 3SB2 Merkblatt

Siemens

Siemens SICAM CMIC Bedienungsanleitung

Siemens

Siemens Infrafern 5TC6 190 Bedienungs- und Montageanleitung

Siemens

Siemens easyTek Bedienungsanleitung

Siemens

Siemens 5WY8462 Bedienungsanleitung

Siemens

Siemens miniTek Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung